1970 Mercury Cougar

Our used handles do not come with this linkage part so if yours is missing this is what you need. Comes with mounting screw as shown.

D0AE-6316-A All 1970-73 351C-2V and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. There is a $50 core charge for this part.*Note - Excludes 1971 and later 351-4V engines. **Note - When ordering double check that you have a 351 Cleveland engine. It is not...

D0AE-6316-A All 1970-73 Mercury Cougar 351C-2V engines, and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. We save the very best used harmonic balancers, those that do not actually need rebuilding. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. Price includes $55 core charge. Refundable $50.00 core...

Includes all 1970 H code 351-2V Windsor engines only. The D0OE-6316-C harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/4 inches, and 3/4 inches thick. 351-2V Cleveland and 351-2V Windsor engines were both used in 1970, they each have specific balancers, please identify your engine and verify your balancer numbers. Has the timing marks on rim. Refundable $50.00 core charge when rebuildable D0OE-6316-C harmonic...

Includes all 1970 H code 351-2V Windsor engines only. The D0OE-6316-C harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/4 inches, and 3/4 inches thick. 351-2V Cleveland and 351-2V Windsor engines were both used in 1970, they each have specific balancers, please identify your engine and verify your balancer numbers. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be...

Includes all X code 390-2V, S code 390-4V, GT-E W code 427, and 428 Cobra Jet engines 1968 - 1970 only. The C8AE-6316-A harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7 inches, and 1-1/16 inches thick. Has the timing marks on rim.  The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to...

Includes all X code 390-2V, S code 390-4V, GT-E W code 427, and 428 Cobra Jet engines for 1968-70 only. The C8AE-6316-A harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7 inches, 1-1/16 inches thick and has the timing marks on rim. Refundable $50.00 core charge when a rebuildable C8AE-6316-A harmonic balancer is received by WCCC. Ford part # C8AZ-6316-B, Ford casting # C8AE-6316-A.*NOTE* Excludes 1967 S code 390-4V...

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable C8AE-6316-C core at WCCC. *Note - Excludes 1969 - 1970 428 non dragpack Cobra Jet engines.Click on images...

ETA FOR THIS ITEM IS 8/23/2023Decent off shore part. Since good used cores are very expensive and almost impossible to find this is often the only choice.

Ford casting number D0ZE-6316-A Includes all 1970 G code Boss 302 engines. Ford master part number D0ZZ-6316-A. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable D0ZE-6316-A core at WCCC. *Note - Excludes 1969 Boss 302 and all non-Boss 302 engines.Click on images to enlarge. This is a picture of a 40 year old piece of rubber removed from a harmonic...

Very nice reproduction of the D0ZZ-15525-A 1970 Mercury Cougar and Ford Mustang 4 speed backup light wiring harness, with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Reproduction radio to door harness for your 67 - 70 Cougar or Mustang.

Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand. NOTE - This does not fit Mustang headlight switches  Here is a helpful...

Reproduction headlamp adjusting nut and screw. Slightly longer screw than stock, small amount of added length does not interfere with anything in or behind the grille. The nut is an exact copy of what is found on the 1969-70 adjustment. Almost the same as the nut found on the 1967-68 Cougar, this isn't even shown on those grilles. 1967-68 mounts on the backside of the headlight bucket. Total of 8 adjustment screws used on each 1967-70 Cougar, item sold individually.Note: When installing...

Screws and spring clips for the tank or reservior for vacuum system

Fits Standard and XR7 Sold as a Kit as Pictured.

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16A and "H", There are four different versions used, but they are the same for the 1969-70 Mercury Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68, but was moved...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used on 1967-68 Mercury...

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up. If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much easier to find inner, high beam lamp distinguished by the number 1 at 12...

Reproduction 4001 incandescent (non-halogen) high beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 2-prong plug and mounts in the inboard position on the car.These are OEM wattage (50 watts) to work with the factory headlight switch, without the need to add relays like you would for higher wattage halogen bulbs.Replaces bulb number 4001. Sold individually, 2 required per car.

Reproduction pair of halogen headlights for any 67 - 73 Cougar or Mustang. These bulbs work for both high and low beam, you simply need to bend one of the tabs back for high beam (see photo above). Keep in mind that you will need a headlight relay kit when installing halogen headlights on your car.  Benefits of switching to halogen bulbs: Brighter lightDramatically improves driver visionOptical lens for a powerful beamLong range high powered lightsCrystal clear glass face with H4 halogen...

Used random 4000 or 4002 brand low beam headlight for the Mercury Cougar. Low beam headlights are distinguished by the number 2 at 12 o'clock and the 3 prong connection on the back. We guarantee these units to work. Replaces basic Ford part # 13007-B.

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

Sold as a pair, these were a one year only feature that allows you to quickly disconnect the hideaway headlight vacuum hose kit a few inches from the firewall. The fittings are slightly different so as not to mix up the connection by crossing the lines.

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16-A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "H", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68 Mercury...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "RL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1967-70 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. These are mostly going to have the C8AB part numbers on them, which is what we have the most of. Included is cups...

Converting your headlight wiring to a modern relay type is probably one of the best 'bang for the buck' mods you can do to your classic car. A must when using modern halogen bulbs, it will also brighten your original incandescent headlights. Normally this is done by cutting the main wiring harness and splicing in a pair of relays. Most of us try to hide the relays under or behind something as well. Not only is this a time consuming task, it can be troublesome if a connection or component fails...

The Mini Relay Kit has everything you need to add relays to your headlight circuit - without cutting your wiring harness. It is equivalent to installing relays into your main harness like it was done for years, but requires no modification to the wiring harness. The differences between this kit and the full kit are redundancy and controller size. This kit has only one controller with two relays designed to handle up to a maximum of 200 combined watts and uses a wiring harness to control...

Complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 1969 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness.NOTE: From the factory, Ford made the alignment tabs different passenger vs driver side...

Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 69 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness. NOTE: From the factory, Ford made the alignment tabs different passenger vs...

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C9ZZ-13076-A, tagged C9ZB-13076-B.*NOTE* A pair of these units were also used on the 1969 Mustang and Mach 1. However, they were not used on the quad headlight 1970 Mustangs.

Reproduction BLACK Headliner with Sunroof for the 1969 and 1970 Mercury Cougar. Two piece kit, one piece for the headliner, and a second piece for covering the sunroof panel. On early production cars Ford pulled the cars off the assembly line to sent them to ASC Golde for install. Golde used 3 bows for installing the headliner, whereas in later production Ford used 2 bows when installing them on the assembly line. These headliners are for 2 bows installations. If you have 3 bows, you will...

Correct Reproduction BLACK Perforated Headliner for the 1969 & 1970 Mercury Cougar Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge.

Reproduction dark green headliner for your 1969 Cougar. Remember that this dark green color is specific to 69. We're still in the process of trying to get the right color for the 70 Cougars, so sit tight, we'll have them soon!

We have finally found a supplier that produces the correct DARK RED perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

We have finally found a supplier that produces the correct LIGHT BLUE perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Light Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

We have finally found a supplier that produces the correct Medium Brown perforated headliner for your 1970 Cougar. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge.

We have finally found a supplier that produces the correct SADDLE perforated headliner for your 1969 or 1970 Cat!Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

Two piece kit, one piece for the headliner, and a second piece for covering the sunroof panel.On early production cars Ford pulled the cars off the assembly line to sent them to ASC Golde for install. Golde used 3 bows for installing the headliner, whereas in later production Ford used 2 bows when installing them on the assembly line. These headliners are for 2 bows installations. If you have 3 bows, you will need to order a standard headliner, then cut it to fit. Check out our video below...

Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge.