1967 Mercury Cougar

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with a V-8 engine and the C-6 automatic transmission. These lines are sold in pairs.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

An exact copy with a beautiful chrome mirror finish.

An exact copy with a beautiful chrome mirror finish. 1 inch deeper than stock.

An Exact copy. Natural gray paint for correct look and rust prevention. 1 inch deeper than stock.

Flawless chrome plating, available in stock depth only. Includes drain plug.

An Exact copy. Natural gray paint for correct look and rust prevention.

Flawless chrome plating, available in stock depth only. Includes drain plug.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

New manufactured transmission yoke for a T-5 5 speed transmission.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Used transmission tunnel specialty cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the area you're working on and send us a few digital pictures so we can cut to your needs. Pricing may not change, because we're...

This two piece painted trim / moulding set helps to secure the package tray in place at the bottom of the rear window. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Replaces Ford part #: C7ZZ-3656-A, concours correct for all 1967 Mustang's and Cougar's. This beveled ornamental plastic ring is for your 1967 steering wheel hub. The inner diameter is 3 3/4" and the outer diameter is 4 3/8" and it stands 5/16" tall. This ring fits many FoMoCo products but keep in mind there is another version that is completely flat like a washer. We suggest you use soapy water and heat your hub before trying to slip this on. It also helps if you go around the perimeter and...

Reproduction driver side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Driver side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1967-68 Mercury Cougar. These special cuts are removed from rust free examples from a used Cougar. Ford part number C7WY-6545119-A.

Reproduction passenger side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Passenger side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1967-68 Mercury Cougar. These special cuts are removed from rust free examples from a used Cougar. Ford part number C7WY-6545118-A.

Reproduction driver (left hand) side trunk floor panel with trunk drop off. This is a complete replacement for the factory spot-welded-in panel, not a partial cut.For more info on this new trunk panel, check out this video below:

Reproduction passenger (right hand) side trunk floor panel with trunk drop off. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

Comes with trunk drop offs and complete tail panel. We would be happy to modify the way in which we remove this part to best fit your needs. Figure about $250 for shipping and crating via www.forwardair.com. Please call to order this one.

Used cover with dull chrome. This used to be a very sought after and expensive part due to how difficult they were to find. Now that our show quality reproductions are here they have little value... Great for someone that just wants their driver to look complete. Fits all 1967-68 Mercury Cougars, Standard and XR7 models. Decal inserts available separately. ...

For 1967 both the XR7 and Standard model used the decal shown on this reproduction trunk lock cover. For 1968 only the Standard model used this decal as the XR7 and XR7G had their own unique center badging. *NOTE* You will have to apply the licensed by Ford decal to the deck lock cover. Click on images to enlarge. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This is for the person who already has a decal or XR7G emblem to place in the center section. Maybe you have a custom idea? Same great quality and flawless fit as our other deck lock covers.*NOTE* After a long hiatus these are finally back in stock! They were worth the wait, the quality is really good on this new reproduction.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This reproduction is pathetic... It's made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. No returns on this product, we suggest no mat is a better alternative than this poor quality reproduction. It's that bad... Please look at our premium quality trunk...

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern by Auto Custom Carpets. Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see elsewhere weigh only a few ounces and flail around inside your trunk every time you close the lid! The pattern will not smudge or wear off easily and it will lay flat and fit...

Complete reproduction trunk floor pan for the 67 - 68 Cougar. Also includes rear shock support, axle bumper mount, and rubber plugs for the shock holes. When ordering this item, keep in mind that it is an over-sized box which will be drop shipped from our supplier in California or available for in store pick up at WCCC. You can expect to pay up to a few hundred dollars for shipping (oversized items must be truck freighted). Often, all you need is the left or right trunk sections. You can save...

Complete non assembled trunk pan kit. Included are the transition panel, trunk floors, rear taillight support and shock support. This kit will require you to assemble and weld in all individual pieces of the rear trunk pan on your own.  This is an oversized box, so expect to pay about $300 for shipping, depending on location.

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

Replacement steel tube for all FE intake manifolds. Tube connects to water pump via a rubber hose. Fits all FE - 352, 390, 410, 427, 428 engines. Best to replace when intake manifold is removed to drive out the old rotted steel tube. We use a little silicone on the smooth surface prior to installation. The connecting hose (and clamps) to water pump normally got painted Ford engine blue from the factory.

Used tube with a tapered end for the vacuum modulator on 1967-68 Mercury Cougar or Ford Mustang with drum brakes and C4 or automatic transmission, but without power drums or power disc brakes. With power brakes the vacuum hose was connected to a fitting in the intake manifold. Pictured in the Bob Mannel Ford Small Block V8 on page 7-26. The basic Ford part number is 7B094.*Note - this tube is not used with disc brakes.

Reproduction tube seat set specific to the 1967 Cougar or Mustang control valve with the 1/4" fitting.

Reproduction machined tube seat set, for all 1968-70 Mercury Cougar and Ford Mustang. Also some 1967 Cougar or Mustang control valve and ram cylindernwith the 5/16" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that early 1967 control valves had 1/4" fittings.

Used parking light / turn signal bezel with near perfect chrome, tested socket and good used bulb. Perfect choice for that all original low mile survivor that shows some patina. Mustang is different and the reproductions must be modified to work on the Cougar. 68 plugs differ from 67 plugs and whereas PS and DS look similar they are in fact side specific. New mounting pads and lens gaskets are sold separate.

Used parking light / turn signal bezel with near perfect chrome, tested socket and good used bulb. Perfect choice for that all original low mile survivor that shows some patina. Mustang is different and the reproductions must be modified to work on the Cougar. 68 plugs differ from 67 plugs and whereas PS and DS look similar they are in fact side specific. New mounting pads and lens gaskets are sold separate.

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Grade B speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G

NOS Speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln.  The 1968 Electrical manual shows a Lincoln part number of C7VA-9D752-G. Service replacement part number is D1VY-13305A. Would need to remove the white tilt bale collar prior to use.

NOS turn signal wand. One year only unique design. The superseded service replacement part # D1VY-13305A Is what most cars have installed in their 1967. Very few of these exist today as they were only made one year. This is the early 1967 turn signal stalk with cruise or speed control. Likely manufactured by Curtiss-Wright.Ford Part number C7ZZ-13305-B2Statistics:1967 Mustang - 55 total cars with speed control option. 17 coupes, 20 fastbacks, 18 convertibles.1967 Mercury Cougars -...

Reproduction Speed or cruise control switch, for factory installed cruise control. Very rare option on a 67-69 Cougar or Mustang, also fits Thunderbird, Lincoln, Marquis. Keep in mind that these new levers will not come with the plastic plug at the end of the harness, you will need to use your old one, or you can splice as shown in the included installation sheet. As you know, these levers were made from plastic in the sixties and seventies. This new reproduction is machined from billet...

Used turn signal wand. One year only unique design. The superseded service replacement part # D1VY-13305A Is what most cars have installed in their 1967. Very few of these exist today as they were only made one year. This is the early 1967 turn signal stalk with cruise or speed control. Likely manufactured by Curtiss-Wright.Ford Part number C7ZZ-13305-B2Statistics:1967 Mustang - 55 total cars with speed control option. 17 coupes, 20 fastbacks, 18 convertibles.1967 Mercury...

This is a cost saving unit when you have a functioning system that just runs slow. The original motor will often make noise and fail to turn in cold weather. This solid state unit will cure that and will sequence your lights fast and silently with no cleaning or adjusting of the points like your original mechanical unit.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is...

*NOTE* According to Phil Parcels of the National Cougar Data Base Project, the approximate cut off VIN for determining EARLY or LATE 67 is: 7F91C547891 Cars with a VIN number higher than this would use the late sequential unit. Cars with a VIN number lower than this would use the early sequential unit. NOTE! If you are unsure whether your Cougar is a late or early model then order this early unit as it works on both. This solid state turn signal sequential kit eliminates all the...