1967 Mercury Cougar

Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.

If your fuel line follows the brake line down the transmission tunnel then you have an early model 1967 and this is the right clip set for you!

Our grade "A" 1967 - 1968 fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Hardware not included but if you ask for it we will try to include it at no charge. Note that the inner part just behind the eyebrow moulding is painted black from the factory.Ford casting number as seen from the back side reads C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. This icon means that we're looking to buy this...

This assembly is spot welded to the fender skin. Sometimes this area will be damaged in a collision but the skin will still be fine. Due to the rarity of good fenders and the costly shipping you may want to consider repairing your fender as opposed to buying another if this is all you need.

New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases, these used shields will need to have the stapled rubber shields replaced. A Mustang shield will not fit a Cougar because the fender has a much different contour.Ford part # C7WY-16A574-A.

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases,  these used shields will need to have the stapled rubber shields replaced. The 1967 and 1968 Mercury Cougar inner fender splash shields were constructed using a metal panel with a rubber material stapled to this metal shield. A Mustang shield will not fit a Cougar because the fender has a much different contour.Ford part # C7WY-16A573-A.*Installation and detailing tip -...

Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.

New replacement gas tank filler cap for all 1967-69 Mercury Cougars and 1970 Cougars without California emissions. This is a vented fuel cap.

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Used service replacement, black plastic filter retainer for the Mercury Cougar, Ford Mustang and other Fords equipped with Midland Booster. It fits between the master cylinder and brake booster on the aluminum master cylinder spacer. The repro and service replacement filter covers are usually black not white.You can find the filter here. ...

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

Quality built new automatic transmission flex plate for all 1967-68 Mercury Cougar and Ford Mustang with 289/302 engines and C-4 automatic transmissions. Looks identical to the OEM Ford plates, has new starter ring installed. Has the correct 28oz. weight for vintage 289/302 engines. The 5.0 liter engines used a 50oz. imbalance.

Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.

Green floor mats for the 67 - 73 Cougar embroidered with the walking cat and Cougar script logos.

Used Grade "A" condition floor mat set for the 67 - 73 Cougar. Front and rear set.Ford part numbers:Two Piece Front - C7WY-6213056Two Piece Rear - C5ZZ-6513106

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

1967 - 1973 Cougar Logo Rubber Floor Mats - Used Dark chocolate brown, correct for Cougars equipped with Saddle, Ginger, or Tobacco interior. Notice this set is the version that is a couple of inches narrower so it will fit well with the addition of convertible inner rockers.

Reproduction passenger side (right hand) floor pan to firewall extension for the 67-68 Cougar.

New manufactured flywheel for manual transmissions. Fits all 1967-68 Mercury Cougar and Ford Mustang with 289 engines with 3 or 4 speed manual transmissions. This flywheel has a 157 tooth ring gear. This flywheel will fit many other Ford small block V-8's with the 157 tooth gear.*Note - Most 1968 and newer Cougars came with 164 tooth flywheels, and they are not compatible.

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Reproduction Front end rebuild kit specifically for the 1967 Cougar with articulated strut rod arms. There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to...

This part is located in the left front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L09-A

New Old Stock NOS retainers for right and left front marker / parking lights for any 1967-68 Mercury Cougar or 1965-1968 Ford Mustang. These are driver and passenger side specific. Replaces Ford part # C5ZZ-13221-C*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

We really cannot justify the average guy buying these over our quality reproduction pair. Only the most tedious of restorations would benefit from having this levels of detail. Sold as a pair, Ford part #: C5ZZ-13206-B for the passenger side and C5ZZ-13207-B for the driver side.

New Old Stock front turn signal lens for 1967-68 Mercury Cougar.  Sold individually, two required per car. This is a factory clear lens for the Cougar, which used an amber light bulb. Mustangs used an amber lens and a unfiltered light bulb. Screws sold separately, you can find them here. Replaces Ford part # C7WY-13208-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

Used vented fuel, or gas cap as installed on 1967-69 Mercury Cougar and 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap. This version does have a check valve, one way vented. This is probably a service replacement fuel cap. Typically, OEM factory caps only said "VENTED", see our related item for that specific gas cap.We stock these in limited quantities, and will have an intact paper gasket. "ANTI SURGE"...

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction fuel line that goes from the fuel pump to the carburetor made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 390-4V engine. Fits all FE engines with Holley 4150, as long as they do not have the Carter "X" fuel pump. Carter X fuel pumps are not crimped together.

Reproduction fuel bowl fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All steel fitting, two needed per carburetor. Sold individually. Check the threads in those Holley bowls prior to installation, often times the bowls are bad.

Reproduction fuel pump for all 1967-70 Mercury Cougars and Ford Mustangs equipped with the 289, 302 or 351W engines. Be aware that this pump has a 3/8 inch fitting for the fuel line.

This is the stainless steel, single prong version fuel sending unit for 67 - 68 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. *Note - This...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1967 Mercury Standard model Cougars and all Ford Mustangs with 16 gallon fuel tanks. This is an original 1967 fuel sending unit with one electrical prong. Ford casting number C7ZF-9275-C. This unit comes with a new 5/16 inch filter, brass float, and sending unit gasket. The only difference between this sending unit and the 1968 sending unit is the diameter of the pickup tube. The 1968 verison of this...

Premium reproduction fuel / gas tank for the Mercury Cougar or Ford Mustang. 16 gallon capacity, correct in every way including the drain cock.Replaces Ford part # C5ZZ-9002. Check out our video on replacing the fuel system on a '68 Cougar! ...

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970.  Ford part # C9AZ-9H576-A.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

Background paint is not sun damaged, guaranteed to work good. If your gauge is cosmetically fine you may consider purchasing our grade B version and using your existing gauge face as they are easy to change out. Check out the video below on our new gauge tester: ...

Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.

Reproduction Glove Box Catch for the 1967 and 1968 Mercury Cougar and Ford Mustang

New old stock 1968 glove box lock. A great optional accessory. All original glove box latches. Includes 2 matching aluminum keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Ford part number C6OZ-6206081-C. Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges. 

NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.

NOS part that shows shelf wear and may need to be repainted in places. For 1967 and early 1968 Cougars built prior 12/15/1967. Can easily be made to fit 1968.  Ford part # C7WY-13A136-B (Headlamp exterior cover) C7WY-13A154-A (Headlamp hinge) Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Used grade "C" driver side (left hand) grille section for use as a patch for those with a break in the section that continues to the fender. Watch the video below to see how to fix your current grille and save a lot of money. Check out our video on grille repair below: ...

Used grade "C" Passenger side (right hand) grille section for use as a patch for those with a break in the section that bolts to the center grille. Watch the video below to see how to fix your current grille and save a lot of money. Check out our video on grille repair below: ...