1967 Mercury Cougar

Good used original handle with no obvious pitting or blemishes. This handle was not used on the XR7. Found on 1967 standard model Cougar and 1967 base model Mustang. Ford casting number C7OB-6222614-A.*Note - 1967 Mustang with deluxe interior, i.e. brushed door panels, used a similar handle, but with Ford part number C7ZB....

New old stock driver side door handle the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. This handle is NOS, NOS doesn't always mean high quality plating. Includes mounting hardware and pads. Round button not included. Replaces Ford Part #: C4DZ-6222405-A

New old stock passenger side door handle the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. This handle is NOS, NOS doesn't always mean high quality plating. Includes mounting hardware and pads. Round button not included. Replaces Ford Part #: C4DZ-6222404-A

Premium concours quality door handle set for the Mercury Cougar. These handles are beautiful triple-plated nickel chrome. Includes mounting hardware and pads. Replaces Ford Part #: C7ZZ-6522404-A and C7ZZ-6522405-A

These two original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...

Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.

C5AZ-6221850-A Door lock knob for all 1967 Mercury Cougar and Ford Mustang. Additionally fits 1965 Ford full size cars such as Galaxie and Thunderbird. 1966-67 mid sized Ford Fairlane and Mercury Comet. Sold individually. Nice used condition.

Convenient matched sets save costly locksmith work. Kits includes a pair of door lock cylinders. Comes with two keys. Includes door cylinder gaskets. Replaces Ford Part # : D2AZ-6521984-A

Please use our contact form to inquire about current colors and conditions of stock on hand. This listing is an example of what you can expect from a grade "A" pair of 1968 decor door panels from us. These are given the grade "A" rating because there is minimal discoloration and light general wear. These panels are very hard to find in grade "A" condition. Most of our panels range in price from $250-$600. NOTE: The pictures shown here are file photos from sets we have sold in the past and...

Used grade "A" pair of XR7 door panels for the Mercury Cougar. Keep in mind you would not want to paint these panels if at all possible as they have streaks of black in them that cannot easily be duplicated. Black panels would be the exception. Also keep in mind these listings are just a sample of what we often have on hand. We are not able to list all of our used panels and ask that you email or call for stock on hand. Most of our panels range in price from $250-$600. Often at least one map...

Great quality reproduction of the interior door strap (grab handle) end cap hardware. This kit is actually our straight grain end cap set, but we include the burl applique decals for you to change out, simply remove the straight grain decals and insert the burl decals. Great price considering good used sold for about $100 before these were available.  ...

Great quality reproduction of the interior door strap (grab handle) end cap hardware. If you have a 67 the woodgrain decals are the correct size, the 68 uses a little different design with a black border which is not available new. The woodgrain is not correct for either 67 or 68. We would highly recommend getting our burl wood applique, it is still not correct, but is much closer and nicer than the woodgrain this comes with. Great price considering good used sold for about $100 before these...

The Best To Be Found. Grade "A" doors have never been dented in, cracked in the door latch area or rusted along the bottom seam. There are no drilled holes for an after market impact strip and the sound deadener is still intact. Occasionally it will still bear the original paint but do expect multiple small door dings. This is the best condition Western door you could ever hope to find, satisfaction guaranteed. Included in the price is a wooden crate, discount applies when you pick it up in...

The Best To Be Found. Grade "A" doors have never been dented in, cracked in the door latch area or rusted along the bottom seam. There are no drilled holes for an after market impact strip and the sound deadener is still intact. Occasionally it will still bear the original paint but do expect multiple small door dings. This is the best condition Western door you could ever hope to find, satisfaction guaranteed. Included in the price is a wooden crate, discount applies when you pick it up in...

These NOS sill plates always have some degree of shelf wear due to the many years they have been shuffled around. The biggest difference you will see with NOS vs. the two different levels of reproductions is the finish. The NOS parts are far less bright and less prone to showing hairline scratches. One other benefit is that NOS sill plates already have the FORD decal in place. Sold individually.

These interchange left to right, they are a mirror image of one another. We recently did a side by side comparison of these so called "concours" sill plates and found very little difference when comparing them to the "economy" version... They both weigh .52 pounds, just like our NOS sill plates. They both have a high of luster, unlike the originals which featured very little "shine". We found the screw holes to be just a tad larger on the economy version but once the screw is inserted you...

Used grade "A" harness, works for driver or passenger side, sold individually. Found on 1967 XR7's and 1967 Standard Cougar with Safety Convenience Package, console or dash mounted warning lights. C7WB-13A769-D is the tag number originally found on the harness. Wiring harness for door ajar and courtesy light. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Ford part number: C7WB-13A769-D

If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.

Good clean, unrestored moulding with no dings or obvious scratches removed properly from the backside with a hammer and wooden block.Ford Master Part # C7WY-6551726-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we...

This is the gear on the upper side of the gearbox. The cables go over each side of the gear.NOTE: Be sure the gear is in good condition so your cables don't get worn out!

1967 - 1969 390-4V engines with 3 or 4 speed manual transmissions. 1969 - 1970 Boss 302 Eliminator 4 speeds. 1970 M-code with 3 or 4 speed manual transmissions. Shaft diameter 3 inches, length 53-1/32" measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

289 and 302 engines - with C4 automatic transmissions or manual three / four speed. Shaft diameter will measure 3 inches. Length 54-3/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.  Ford part # C7WY-4602-E.*NOTE* This is a solid one piece drive shaft.

This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...

Used rectangular center duct tube for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory air conditioning. Wire reinforced foam, will show some snags or signs of use. Will not have gaping holes. Was originally stapled to the center housing. Ford part number C7ZZ-19B680-B.

Used disc brake dust shield specific to the factory installed Kelsey Hayes disc brake systems on the 1967 Mercury Cougar or Ford Mustang. Right and left the same. Clean Western part with no heavy corrosion like you see on Eastern cars.Ford part # C7OZ-2K004-B.

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fits many 1967 - 1968 Full size Mercury cars and 1967 - 1969 Mercury trucks. This emblem measures 6 3/8" total width and the "M" is 2 1/8" tall. The bottom mounting studs located on the letter "M" and "Y"...

Ford part number is C7WY-16098-A, casting number as seen on the back of the emblem is C7WY-16720-A. Very rare find, only used on 1967 non GT cars equipped with the S code 390.See related item Barrel nut if missing attaching clips. 3/16 inch stud.

This Mercury script emblem is mounted onto the driver side fender extension. This is an original part still in the Ford box, engineering number on the back of the emblem reads C7WB-16098-A, Ford part number is C7WY-16604-A.

These always are peeling. Located on the right side on the dash face...

Used emergency / parking brake assembly for a Mercury Cougar or Ford Mustang as removed from a West Coast Cougar organ donor. This unit may have some minor rust. Normally we assemble with reproduction cable.Ford part # C7ZZ-2780-B.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 289 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6AE, C8AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 6K4 or October 4, 1966.  This item cannot ship...

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.

Chassis black aerosal paint for all 1967-73 Mercury Cougar and Ford Mustang engine compartments. High temperature (advertised up to 350°). Manufacturer boasts resistant to cracking and flaking, chemical resistant to gasoline and brake fluid (but don't let brake fluid accumulate). *NOTE* Chemicals can only ship UPS ground only. Please, no foreign orders or USPS shipping allowed.Check out our video below on chassis upgrades: ...

New high temperature enamel for painting your block and underhood parts. So far, the best match has been the VHT brand, SP125 "Dark Ford Blue" paint (sometimes called "Ford Corporate Blue"). This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel. ...

Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A

Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

Factory original cast iron exhaust manifold for the passenger/right side and is probably a mid-year change for 1967. For both S & X code 390 engines and W code 427 GT-E engines up until 2/15/1968. Butterfly spacer not included. Ford part # C7OE-9430-C.

C6OE-9428-A 390-4V factory original cast iron exhaust manifold for passenger side. Even though the photo shows a chamfer where an exhaust donut would go, the proper 1967 manifold would have been cast flush, and a butterfly spacer would have been used. The spacer had a flapper that partially blocked the pipe and allow heat to be dissipated upwards to the choke. Spacers not included. We suggest purchasing the later version of manifold that did not use the spacer. *Note, a spacer may be needed if...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. The pictures show an example of how it looks once installed. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. Also found on various 1976-70 Ford and Mercury cars such as Galaxie, Fairlane, Torino, Ranchero, Falcon, Montego, and Thunderbird. The knobs...

Used original fan shroud for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. Shround will have minor damage as shown. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. Ford part # C9OZ-8146-A For some helpful tips on upgrading your Cougar (or Mustang) cooling...

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.

Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.