1968 Ford Mustang

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1076 WHITE Led Plasma back up light bulb for your 67-68 or 71-73 Cougar, Mustang or anything else you might have that takes an 1076 bulb. Please note that these bulbs are ground sensitive. Specs: Power: 7.5 Watts Brightness: 300 Lumens Total life expectancy: 30,000 hours 2" Tall (1 3/8" extends out of the socket) Comparison image - Click to view full-size: ...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 back up light bulb for your 69-70 Cougar or Mustang. (67-68 and 71-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175) These Plasma LED bulbs will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1157 WHITE LED Plasma stop lamp / turn signal light bulb for your 67 - 73 Cougar, Mustang or anything else you might have that takes a white 1157 bulb. Please note that these bulbs are ground sensitive. Did you know that white (clear) 1157 bulbs fit a ton of other cars and trailers from the 50's clear through the 90's and beyond that used the...

24" hose with metal coil (like original) instead of plastic coil found in most. Coils are wrapped in a 6+ mil plastic rather than the 3 mil plastic that you can easily put your thumb through. Does not come with clips. May require being cut to fit some applications. 2 required per car. Replaces Ford Part #: B5A-18556-C.Replaces Ford Part #: B5A-18556-C.

This face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are going to be missing that piece, because after all......that dampener has been in there for up to 46 years! (this doesn't effect its useability). You can use your existing...

When placing your order, be sure to leave a note as to which color you're looking for and we'll do our best to find them for you. Limited quantities available. This colored face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are...

These reproduction face plates fit inside the buckle bezel on the two piece type seat belt buckle cover. Sold as a pair. You can use your existing spacer, or if you're missing one, you can find it here. Check out our video "All about seat belts" below. ...

This is the complete one piece seat belt buckle cover which comes with the face plate (with the round cutout for the push button) and the bezel all in one. This version is handy when you don't want to deal with multiple parts (as is the case with the separate face plate and bezel version). Simply remove your old cracked or broken cover, replace the metal spacer, and pop this cover into place and you're ready to go! You can use your existing spacer, or if you're missing one, you can find it...

Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column and inside of the sleeve. Do not remove the crease on the plastic, you need it to help you put the sleeve on the tube. Push the sleeve on as far as you can. Gently tap the sleeve down on a table top...

Used cover plate or thrust plate that retains the camshaft on the front of Ford small block V-8 engines such as 289, 302, 351W. 1967-70 Mercury Cougar or Ford anything. This plate has three bumps, we have found a Ford number of C9OZ-6269-A, this may be a service replacement number and could be found on engines built earlier than 1969. We have found this style of 289's from 1967. There is another version with Ford number C2OZ-6269-A, it only has two bumps.

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502639-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, kind of shaped like the State of Arizona, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502667-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502638-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side upper only, kind of shaped like the State of Arizona, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502666-A.

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

Brass screw in plug for select Autolite distributor vacuum advance units from 1968-71, typically the banded single advance units factory installed. Solid brass, originals were not, we believe that they were cadmium plated. Solid plug, should be hollow, with a 3/4 inch hex head. Works as it should. Fits most all vacuum advance that have a plug in the end as shown. *Note, when removing the old plug, there is a spring and washer inside. 

These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up. Plug size: 1 1/2"   also used for the electric headlight conversion kit for the firewall pass through body plug.  

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

This kit includes 38 pieces that include quarter panel drain valves.

These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up.Plug Size 1 1/2"

Set of 4 seat mounting access floor pan plugs, enough for one seat. 2 kits needed for both bucket seats. This is a good idea to pick up two sets of these when replacing carpeting. These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up. Plug Size 1 1/2"

Single used post for 1968 dual post head rest. Sold individually, two used per head rest. Ambidextrous, can go on either side, notches to the inside. Comes as shown, chromed rod, nut and lock washer. Fits any 1968 Ford with dual post headrests.  

Reproduction master cylinder decal for the 1967 - 1969 Mercury Cougar or Ford Mustang. This decal was not used on later year cars. These types of decals are for the person to whom details matter.  Customer feedback found at mercurycougar.net:  Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are...

C8ZZ-3A713-A Return or low pressure hose. Low pressure hose from the control valve to insulator. 1968-70 Mercury Cougar Ford Mustang all V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the low pressure hose from the control valve to the pump. This is the lower half only. Please see part number 42301 for the upper section that works with this hose.

High pressure hose from the pump to insulator. All correct ribbing, striping, and crimping.*Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only.Stamped with C9ZA-3A719-A.

Pair of correct power steering hoses for your 67-69 Cougar or Mustang. All correct ribbing, striping, and crimping. Hoses have 5/16" fittings. *Note: Cannot be used with the very early 1967 1/4" fittings on control valves and ram cylinders. *Note - Two different hoses attach between the control valve and the ram cylinder. Part numbers: C60A-3A717-A C60A-3A714-A

C6OA-3A717-A pressure hose. Ram cylinder to control valve. All correct ribbing, striping, and crimping. Hose with 5/16 fittings used 1967-69 Mercury and Ford. *Note - Two different hoses attach between the control valve and the ram cylinder PS7U1B and PS4U1A. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders.

C6OA-3A714-A pressure hose. Control valve to ram cylinder. All correct ribbing, striping, and crimping. Hose with 5/16 fittings used 1967-69 Mercury and Ford. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders. *Note - Two different hoses attach between the control valve and the ram cylinder PS7U1B and PS4U1A.

Reproduction multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Does not include dipstick. Manufacurers note: In place of the paper gaskets, it is recommended that you use gray atv...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

This after market adjustable proportioning valve is far superior to the original equipment. Fully adjustable for tuning front to rear brake bias. Requires some routing modifications of brake lines for proper fit. Includes adapter fittings. Replaces Ford part # C5ZZ-2B091-A, or C7OZ-2B091-B.Fits: 1967 Mercury Cougar 1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang 1968 Ford Mustang 1969 Ford Mustang 1970...

Used proportioning valve for the 1967-68 Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. For 1967 Cougars, this valve is most often found at the junction of the high pressure hose back at the rear end. 1968 had it connected to the distribution block on the driver side firewall. Will come with the C7OE-... stamped valve. Starting in 1969 the valves had a C9OE... Ford part number. These are used...

Reproduction proportioning valve for the Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. This valve is most often found at the junction of the high pressure hose back at the rear end, or later, found with the distribution block mounted on the driver side apron (inner fender). Replaces Ford part # C7OZ-2B091-B.Here’s a video to help you rebuild the distribution block and proportioning valve: ...

This plate attaches the 3/8" steel fuel line under the driver's side rear torque box, as it makes its way from the rear frame rail out to the rocker area. It acts both as a mount and as a protector from road debris. These were used on late 1967 to 1968 Cougars and Mustang with the 3/8" fuel line. Early 1967 cars had smaller 5/16" fuel line, and different routing (through the transmission tunnel), and did not use this part. Mounting bolts included.

This plastic protector sleeve is often missing or broken, but occasionally we come across a good used one. This part attaches just in front of / below the fuel tank on the passenger side, and serves two purposes: it routes the wiring closer to the fuel sending unit without it dangling down, and protects it from road debris This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Good used double sheave alternator pulley.Ford Part #: C5AF-10A352-J.

Reproduction alternator pulley, single sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Used stamped steel single groove alternator pulley, typically these are described as being 2-7/8 inches in diameter. We find various casting numbers on them, such as: C5AF-10A352-F1, C5AF-10A352-G1, C5AF-10A352-K, C5AF-10A352-L.Replaces Ford part number C5AZ-10344-K.

C7AZ-6A312-A. Double or two groove crankshaft pulley. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. 6-1/8 inches in diameter. 1967 Application - Mercury or Ford 289 with automatic transmission and standard cooling (17 inch radiators). Without air conditioning and without power steering. 1968 Application - Mercury or Ford 289 or 302 with or without power steering. Thermactor emissions permissible. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. ...

Ford part number C8AZ-6A312-C. Application 390-2V and 1968 - 1969 390-4V engines without air conditioning and with power steering. Ford casting number C8AE-6312-C. Double sheave 68 69 crank pulley.