1968 Ford Mustang

This reproduction of the 3 and 4 Speed Shift Boot has a metal core base just like original as is the texture. Fits the 67 and the 68. Replaces Ford number C5ZZ-7277-B. Customer feedback found at mercurycougar.net : When I bought my 68xr7 from Don two years ago, our deal was that he would keep the new Magnum 500's and BFG tires that were on the car. I asked him if he would just put some "rollers" on to get the car on and off my dad's trailer. When I got the car, he had put on a...

This bezel was never offered from the factory on a Cougar, but is a very attractive part for those with a manual transmission and no console. This unit works with three or four speed manual transmission and with a rubber or leather shift boot.

Original style, factory 3 speed lower shift boot.Replaces Ford part #: C6ZZ-7138-B

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This shifter dial was originally attached with heat to a pin connector. To reattach we suggest using glue. These look like it would be easy to detail the white letters for P R N D 2 1 with a careful hand. May have a chipped corner that is not seen when installed. Ford part # C7ZA-7A213A Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Shift kit for the C4 transmission valve body for all 1967-67 Mercury Cougar and 1967-69 Ford and Mustang. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.

Nice reproduction 3 speed black shift knob for the 1968 Mercury Cougar and Ford Mustang and other floor shift Ford products from 1968. Thread size is 7/16-20, will not fit on 1967. Ford part number C8OZ-7213-B. Check out our video on rebuilding your shifter below: ...

This one might cost a couple dollars more than others you may have seen but it is the best in my opinion. This is correct for a standard Cougar, XR7 had a woodgrained finish. Check out our video on rebuilding your shifter below: ...

Attractive knob used on later 68 through 69 non XR7 Cougars. I recently installed one of these on my own cars and had the face fall off the main body the first time I used it. I glued it back on and have had no problems since. Replaces Ford Part #: C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

For those who want to want a correct looking interior in conjunction with their modern transmission. Check out our video on rebuilding your shifter below: ...

Used on both XR7 and standard Cougar consoles. Differs from shifters made for non console use in that is has a small loop to connect the white plastic arm to the shift indicator light. Fits 1967-68 Mercury Cougar and Ford Mustang with factory consoles. Good used part no heavy pitting on the chrome, comes with complete with cable assembly inside. Ford part number C7ZZ-7210-C. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang with consoles. This console lever is unique to console equipped cars, it has a tab with a hole in it for accepting the shift indicator indicator rod. We sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang without consoles. The 1967-68 is similar to the 1969-73 shift lever, but has the additional chrome window section for holding the indicator light. These have been re-chromed, we sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-A. This lever was also used on the 1968 XR7-G cars with unique consoles.*Note - Chromed lever only, sold without cable, pawl, handle,...

Check out our video on rebuilding your shifter below:

Reproduction shifter assembly for the Mercury Cougar or Ford Mustang equipped with the automatic transmission, but without a center console. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1967-68 Mercury Cougar or Ford Mustang without consoles. The 1967-68 is similar to the 1969-73 shift lever, but has the additional chrome window section for holding the indicator light. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C7ZZ-7210-A. This lever was also used on the 1968 XR7-G cars with unique consoles. *Note -...

This quality reproduction 1967 Mustang part can easily be made to fit your 1967 - 1968 XR7 or 1967 standard Cougar manual transmission console simply by drilling the two holes near the front for the spring clips that attach the pad to the console. See the diagram below for correct hole size and location. This plate was used on both three and four speed manual transmission Cougars equipped with the optional center console. Not for use on 1968 standard / decor consoles. Replaces Ford Part #:...

Automatic shifter cable with slot on the threaded end for all 1969-73 Mercury Cougar and Ford Mustangs. Will also work on 1967-68 but features a slot at bottom so as to remove or adjust easily. The 1967-68 version did not have this slot. Ford part number C9ZZ-7D246-A with the slotted threaded stud on the end. Also fits 1971+ Maverick & Comet with automatic floor shifters. Restoration Hint - We suggest purchasing this upgraded cable for use in 1967-68 shifter levers. Much easier to install, and...

Automatic shifter arm pawl - early version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1967-70 Mercury Cougar, 1965-70 Ford Mustang, and 1965-66 Ford and Mercury full size cars with floor shift automatic transmissions. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need, this early pawl has a Ford part number...

Complete console shift assembly for the 67 - 68 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm. Ford part numbers: C7ZZ-7210C C7ZZ-7A306A C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

C8ZZ-7400-A4Assemby 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang after 1-2-1968. Small block 289 and 302 engines only. Includes shifter mechanism, shift rods, and shift lever. Knob not included. All in used condition. The 1-2-1968 date was the transition of the stronger trunion for the shifter mounting. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 302-4V engine. ...

Reproduction shifter boot for aftermarket shifters on 67 - 68 Cougars, or 64 - 68 Mustangs. Perfect fit for Hurst shifters and will accommodate other aftermarket shifters.   

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

This shifter bucket is used on all 1967 - 1968 Mercury Cougars and Ford Mustang with an automatic center console. Bare bucket with good shift detentes and bushing hole that isn't worn out. Ford part number C7ZZ-7A306-A Check out our video on rebuilding your shifter below: ...

This shifter bucket is used on all 1967 - 1968 Mercury Cougars and Ford Mustang without an automatic center console. Bare bucket with good shift detentes and bushing hole that isn't worn out. Ford part number C7ZZ-7A306-B. Check out our video on rebuilding your shifter This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to...

If your automatic floor shifter has play in it left to right then this is the culprit. Easy to install, (more difficult if you have a 67-68 with center console) these are made from a wear resistant plastic that is better than original. Sold as a pair as two are required per car. This bushing was used in all Ford products equipped with a floor shift automatic from the 1965 Mustang to the late 70's Pinto. Replaces Ford Part # C5ZZ-7A133-A Check out our video on rebuilding your shifter below: ...

Rechromed 1967 deluxe shifter button. Unique to the deluxe faux leather wrapped T handle shifter starting in 1967. One year only design, this one has a convex button for you thumb. Starting in 1968 the button was more rounded to comply with the added safety features mandated in 1968. Core deposit is required, fully refundable with returned 1967 deluxe button. Ford part number C7ZZ-7C488-B. Check out our video on rebuilding your shifter below: ...

Steel retaining plate. Ford part number C5ZZ-7B233-A. This plate is needed to fasten the shift indicator bezel on non-console cars. Fits 1967-68 Mercury Cougar and 1965-68 Ford Mustang, without console. Nice reproduction part, better value than used. You may also need a set of 4 attaching screws. Check out our video on rebuilding your shifter below: ...

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1967 - 1968. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one.Replaces Ford Part #: C5ZZ-7213-F.

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Good used shift indicator light and pigtail for the 1968 with automatic and without console. Comes as shown with the clip on diffuser for automatic shifter lever. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...) The 1968 wiring harness has a blue double male plug. Fits 68 CougarFits 68 Mustang Check out our...

C5ZZ-7210-C Shift lever for all 1967 Mercury Cougar and Ford Mustang and 1968 until 1-2-1968. The early lever can be identified by measuring the distance between bolt holes. 1-13/16" spacing between the holes is the C5ZZ-7210-C lever. *Note - Must be used with Trunion C5ZZ-7210-D, sold separately.

C5ZZ-7400-D 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968.

Adjustable rod that connects the floor shifter to the "Select-Shift-Merc-O-Matic" automatic transmission. C4 transmissions only, code "W" on your door data plate tag. Small block 289/302 engines received the C-4 automatic transmissions. Rod marked C7ZA-7326-B. Shift rod approximately 17-1/4 inches long. Check out our video on rebuilding your shifter below: ...

Reproduction adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions.Includes pin and nut. Shift rod approximately 18 inches long. Replaces Ford part number marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions. Shift rod approximately 17 inches long. Rod marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

4-Speed shifter rod hardware kit for 67 - 68 Cougars and Mustangs with a 4-speed transmission. Check out our video on rebuilding your shifter below: ...

This hard plastic part slips over your floor shifter stem and keeps coins and such from falling inside your center console. Replaces Ford part number C7ZZ-7C445-A. Check out our video on rebuilding your shifter below: ...

Reproduction "U" shaped bracket that attaches the 3 /4 speed shift lever to the shifter control assembly. For use on all 67 - 68 Mercury Cougar and Ford Mustangs with the 3 or 4 speed shift lever, and 1968 shift levers through 1-2-1968. Measurement of hole spacing is 1-13/16 inches on center. *NOTE - Must be used with 3 speed shift lever C5ZZ-7210-C, or 4 speed shift lever C5ZZ-7210-M. Replaces Ford part number C5ZZ-7210-D Check out our video on rebuilding your shifter below: ...

KYB Gas-a-just shocks are America's best selling performance gas shock. It's monotube design features a higher gas pressure which helps to hold the tire to road surface during severe driving conditions. N2 gas helps eliminate shock fading due to aeration and foaming. This shock is the perfect choice for the performance oriented. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.029.614.41-X- ...

These are equal in performance to other name brand high pressure gas shocks at a significant lower price. These shocks are best suited for drivers looking for firm ride with a solid controlled “feel of the road”. These units are sold individually.

This gas shock improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock. Also, this is the most stock-looking shock since it's black and has a flat upper collar. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.259.334.92-X- ...

Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually

If you buy this reproduction tower, you will no doubt save you time in clean up. But nothing will ever fit and look like original FoMoCo towers!Here's a little film to help you fortify your flexxy feline!

Excellent condition tower as cut from a Western parts car. No specific part number for this structural front suspension section.Generic Ford part # C7ZZ-16055-D or E, includes apron and side member.Here's a little film to help you fortify your flexxy feline! ...