1968 Ford Mustang

Used rectangular center duct tube for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory air conditioning. Wire reinforced foam, will show some snags or signs of use. Will not have gaping holes. Was originally stapled to the center housing. Ford part number C7ZZ-19B680-B.

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

Correct cast aluminum elbow fitting for the rear of the C8AZ-9A486-C smog pump. This elbow will have two single mounting holes. The service replacement elbow (Ford part number D4TZ-9C475-A) has two sets of double mounting holes. Correct Ford part number C8AZ-9C475-A.

Concourse Correct 90 degree elbow that attaches to the intake manifold and provides proper clearance for the emission canister and air cleaner housing. Correct for all 1968 S code 390-4V, W code 427-4V and R code 428 Cobra Jet engines.

These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD

Used emergency / parking brake assembly for a Mercury Cougar or Ford Mustang as removed from a West Coast Cougar organ donor. This unit may have some minor rust. Normally we assemble with reproduction cable.Ford part # C7ZZ-2780-B.

Used end cap with the burl woodgrain for the deluxe door pull straps found in the Mercury Cougar XR7 or Ford Mustang. These units will show a degree of pitting, fine scratches and fading. Also, these door pull strap caps are unique to 1968 and they are not currently being reproduced. 1967 has no border and the woodgrain has a different color and look to it. This is for the person that must have correctness in detail or they just need one to finish off their interior. We highly recommend...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 289 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6AE, C8AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 6K4 or October 4, 1966.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 7l17 or November 17, 1967. This item cannot ship through any...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 7M16 or December 16, 1967. This item cannot ship through...

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.

Chassis black aerosal paint for all 1967-73 Mercury Cougar and Ford Mustang engine compartments. High temperature (advertised up to 350°). Manufacturer boasts resistant to cracking and flaking, chemical resistant to gasoline and brake fluid (but don't let brake fluid accumulate). *NOTE* Chemicals can only ship UPS ground only. Please, no foreign orders or USPS shipping allowed.Check out our video below on chassis upgrades: ...

New high temperature enamel for painting your block and underhood parts. So far, the best match has been the VHT brand, SP125 "Dark Ford Blue" paint (sometimes called "Ford Corporate Blue"). This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel. ...

Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A

Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

Factory original cast iron exhaust manifold for the passenger/right side and is probably a mid-year change for 1967. For both S & X code 390 engines and W code 427 GT-E engines up until 2/15/1968. Butterfly spacer not included. Ford part # C7OE-9430-C.

C8OE-9431-A Factory original cast iron exhaust manifold for driver side.

Used pair of Exhaust Manifolds / 428CJ for the 1968 Mercury Cougar / 1968 Ford Mustang 

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. NOTE: Dwayne from "The Brothers Car Collection" clued us in to the fact that the choke tube fitting on the passenger side is indexed 180 degrees off on some sets we sell. Fortunately you can carefully spin it around with vise grips so the opening faces...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Used Transition cover for the 68 - 69 Cougar or Mustang tilt steering column. This cover bolts to the outer cover tube.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. The pictures show an example of how it looks once installed. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. Also found on various 1976-70 Ford and Mercury cars such as Galaxie, Fairlane, Torino, Ranchero, Falcon, Montego, and Thunderbird. The knobs...

Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option. All of them were black in color. Later they were available in colors. We also have blue available, see our related tab. Replaces Ford part number C8AZ-18C490-B.

Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option.Typically you only see black grilles. Later they were available in colors. We have this blue available. Replaces Ford part number C8AZ-18C490-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to...

Great addition to that show quality FE powered early Cougar. Unlike the reproduction this has the original part number, BARNUM BROS. FIBRE CO. INC. lettering and FoMoCo insignia at the top driver side. This was one of the last units out the door when FORD discontinued them in the 1990's. Weighs 2.70 pounds and the reproduction weighs 1.54 pounds. Ford part number C8ZZ-8146-A

Used original fan shroud for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. Shround will have minor damage as shown. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. Ford part # C9OZ-8146-A For some helpful tips on upgrading your Cougar (or Mustang) cooling...

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.

Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.

Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.

New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.

Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Used service replacement, black plastic filter retainer for the Mercury Cougar, Ford Mustang and other Fords equipped with Midland Booster. It fits between the master cylinder and brake booster on the aluminum master cylinder spacer. The repro and service replacement filter covers are usually black not white.You can find the filter here. ...

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

Quality built new automatic transmission flex plate for all 1967-68 Mercury Cougar and Ford Mustang with 289/302 engines and C-4 automatic transmissions. Looks identical to the OEM Ford plates, has new starter ring installed. Has the correct 28oz. weight for vintage 289/302 engines. The 5.0 liter engines used a 50oz. imbalance.

Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.

Used OEM Ford 428 Cobra Jet manual transmission flywheel. Stamped C8OE-A. Needs a ring gear, has chipped teeth. No visible issues, no discoloration from heat. Ford 428CJ only, not for 428 SUPER COBRA JET engines. This flywheel on a 428CJ is externally balanced. Should have 184 ring gear teeth.Ford part number C8OE-6380-A.

New manufactured flywheel for manual transmissions. Fits all 1967-68 Mercury Cougar and Ford Mustang with 289 engines with 3 or 4 speed manual transmissions. This flywheel has a 157 tooth ring gear. This flywheel will fit many other Ford small block V-8's with the 157 tooth gear.*Note - Most 1968 and newer Cougars came with 164 tooth flywheels, and they are not compatible.

Original OEM light found on early cars and later recalled. EXACTLY 100% correct with the right serial numbers in the right places as per the blueprints from Shelby American: * IGM 1642 PN on the bottom right * K11123 N14 cm AUF 5m up the right side * No numbers on left side Marchal made several versions of this light, only this one is the correct one for your Mustang. It has the famous 'cat eyes' internal diffuser. Reproduction lights use a different bulb, lack the diffuser and have the word...

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Core bench seat for the 1968 Mercury Cougar or Ford Mustang equipped with decor interior. 1968 bench seat without optional headrests, but with seat seat back release latches. The foam will almost always be deteriorating or even missing. All seat cores will be solid frames taken from a Western parts car. Keep in mind 68 and 69 are identical except for how the head rests attach. You can easily add head rests from 69 buckets and bolt them to a 68 pair of buckets or bench if you have all the...