1968 Mercury Cougar

Core aluminum rear deck lid moulding / trim for the Mercury Cougar. Good core ready for restoration. No kinks, flattened areas of heavy pitting. Seven clips are used to install the deck lid moulding and we have new clips available here. Ford part # C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on this tricky trunk trim, check out our video below: ...

NOS aluminum deck lid moulding / trim for the Mercury Cougar. Rarely do we come across a true NOS 1967-68 aluminum deck lid moulding / trim. Starting in 1969, Ford gave you a stainless moulding as a service replacement part. Seven clips are used to install the deck lid moulding and we have new clips available here! Ford part # C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on this tricky trunk trim, check out our video below: ...

Used aluminum rear deck lid moulding / trim for the Mercury Cougar. Our used trunk lid trim is usually dull and lightly scratched as you see pictured here. Expect numerous and heavier scratches in the key hole area. We have a really hard time keeping good, straight used aluminum deck lid mouldings in stock. They are very prone to damage and many have been replaced with the 1969-70 stainless steel version which was the standard service replacement part that Ford would have sold you from 1969...

Core driver side (left hand) lower rear window moulding / trim for the Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42405-A.

Core passenger side (right hand) lower rear window moulding / trim for your Mercury Cougar suitable for restoration or could be used on a lower quality driver. Ford part # C7WY-42404-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Used passenger side (right hand) lower rear window moulding / trim for your Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42404-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section....

Sold individually, right is the same as left. Rare find but hard to justify the price in light of the quality and price of the reproductions we offer at a fraction of the price. Notice the difference in brightness of these two NOS, fresh out of the Ford wrapper mouldings. This is actually quite common, different batches got different treatment. When you send in your trim to us to be restored it will match as it will all be done in the same "batch".

This used to be a decent off-shore quality pair of anodized aluminum mouldings. Our guess is that the tooling is starting to show wear and needs replacing as evidenced by the wrinkles in the corners. We have alerted the manufacturer but they can be slow to act. There are no returns on this blemished, less than perfect part. Ford issued a TSB (technical service bulletin) instructing the Service Departments to drill a hole through the rocker moulding into the lower fender and install a chrome...

NOS passenger side front wheel lip moulding. Rare find, better snatch it up while you can!

Driver side upper windshield mouldinig. Suitable for restoration or could fit right in on or your lower quality daily driver. Ford part number C5ZZ-6503145-B.

NOS upper moulding at the top of the windshield on the left hand side. Ford part number C5ZZ-6503145-B

Driver side vertical windshield moulding. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part number C5ZZ-6503137-B.

Core lower windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503148-B.

Core passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503144-B.

Core passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503136-B.

NOS passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503136-B.

Restored six piece anodized aluminum front moulding / trim set for the Mercury Cougar. We suggest you make the order online and then send your cores with a copy of your invoice. Once your cores arrive we will ship the restored set.  If you do not have good cores we do have them for sale. These restored original trim parts have the correct satin "bright dip" anodized finish and look like NOS! We have sold hundreds of these trim parts to Cougar owners all over the world, many of which are...

Restored six piece anodized aluminum front moulding / trim set for the Mercury Cougar. We suggest you make the order online and then send your cores with a copy of your invoice. Once your cores arrive we will ship the restored set.  If you do not have good cores we do have them for sale. These restored original trim parts have the correct satin "bright dip" anodized finish and look like NOS! We have sold hundreds of these trim parts to Cougar owners all over the world, many of which are...

NOTE: This listing is for a pair of blemished mouldings, please see the above photos for examples of blemmed pieces. This is the right hand and left hand 1/4 panel moulding. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number...

NOS anodized aluminum rear moulding / trim set for the Mercury Cougar. Rare find in NOS form and all three trim parts come with original packaging.Ford part #'s: Driver side rear quarter extension trim C7WY-6529313-A, passenger side C7WY-6529314-A, and center trim C7WY-6542512-A Normal 0 false false false EN-US X-NONE X-NONE . ...

Used anodized aluminum three piece rear moulding / trim set for the Mercury Cougar. Used driver quality set with no obvious dings or deep scratches. Better than our core sets in that they have more luster and less damage. Keep in mind these are off a 40 year old parts car.Ford part #'s: Driver side rear quarter extension trim C7WY-6529313-A, passenger side C7WY-6529314-A, and center trim C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on...

Core four piece rear window moulding / trim set for your Mercury Cougar. These stainless steel mouldings will have light scratches and minor dings and are suitable for restoration or for a lower quality daily driver. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim. Ford part #'s: Driver side upper C7WY-42431-A, driver side lower C7WY-42405-A, passenger side upper C7WY-42430-A, passenger side lower C7WY-42404-A.*NOTE* Keep in mind we buy most...

Used four piece rear window moulding / trim set for your Mercury Cougar. Good used four piece set with no dings or heavy scratches. Ready to install on your Cougar as is or polish them to a mirror like finish to be installed on a show car. These are above average original FoMoCo mouldings and are ready to install as-is. No disappointments. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY. Ford part #'s: Driver side upper C7WY-42431-A, driver...

NOTE: Some modification required to fit Cougars! These are actually 1971-73 Mustang wheel lip mouldings, which have a much different shape / contour than Cougar and will need minor modifications to make fit. That being said, they are the closest alternative we have found that can be made to fit and look reasonably good for much less than restored originals or NOS. This set is what we refer to as the "Better than nothing" option. No complaining or whining please... Check out our video below,...

This set of four 1967 - 1968 wheel lip mouldings are sold on an exchange basis. If you have extra cores you would like to send in for credit then we would like to hear from you! Please do not send heavily damaged, torn, corroded or kinked trim as the finished product will be delicately thin or not able to be restored at all. Extra screw holes and elongated holes are OK but you will be getting a like product in exchange. We are happy to send your specific cores in for restoration and make sure...

This is a core five piece set of front windshield mouldings for a 1967 - 1968 Mercury Cougar. These mouldings need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard mouldings of that description. We do not recommend the reproduction, "offshore" mouldings that are available as they...

This "offshore" set of low quality reproduction windshield mouldings / trim are sold only as a set. You will not want to mix and match these reproduction units with used because the color and quality will not match. These are guaranteed to look bad and fit even worse. No returns, no exchanges. We strongly suggest that you purchase our restored or good used set. And yes, these are the exact same trim parts supplied by the other vendors with a completely different description. Check out our...

This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Available in correct OEM Black. customers looking for a little more flash under the hood might be interested in the highly-polished stainless steel version of this bracket! Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

Good reproduction but our used unit is a better value and will clean up just as nice.

Reproduction pair of mounting nuts for any 68 - 70 Cougar or Mustang with power brakes.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang. Original Ford part number C8MY-1424-A. About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels.

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

These spacers are required to properly mount the trunk lock housing to the trunk. Two required per car, sold individually. Ford part number C7WY-6543565-A. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found on cars with 427-4V, 428CJ, 429CJ, Boss 302, Boss 351, or Boss 429. These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: 8L27, November 27, 1968; 0E29, May 29, 1970. Please have your desired date in mind when calling or place it in the comments section of your on-line order. We have removed the peg leg gears and parts...

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Used stamped nut for attaching the tail light bezels to the tail light housings. This is a 8-32 nut, with a 11/32" hex and is intended for the 8-32 threaded studs attached to the tail light bezels on any 1967-68 Mercury Cougar. Sold individually, 10 per side, or 20 per car.Replaces Ford part number 45203-S.

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Precision machined to the factory specifications. Light gold anodize finish just like the original.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

The oil filter made by the original Ford supplier.