1968 Mercury Cougar

Good used part with no pitting or scratches. Correct for all 1968 steering wheels and 1969 Cougar's equipped with the standard level interior.

Decent used horn ring but unlike our grade "A" used horn ring this one will have very minor pitting but no open blisters in finish. Good value for your driver quality 68-69 Ford / Mercury with two spoke steering wheel.

Reproduction Two Spoke Steering Wheel Horn Ring for the 1968 and 1969 Mercury Cougar. This is a very good reproduction piece. The original horn contact pieces fit nicely. This casting, while different than the 1968 version with the empty cavities is actually stronger. *NOTE* Save your old horn ring, you will need to transfer the rubber spacer and the horn contacts to this reproduction part.*CUSTOMER REVIEW* Called WCCC the other day after calling around to a lot of garages and auto parts...

Tested and working used pair of Hi and Lo tone horns. 1967-68 Mercury Cougar used part number C7WF-13802-B and C7WF-13801-B. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.NOTE* - Hi tone = passenger side / Low tone = driver side

Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 1/26/70

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/67

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/28/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 12/5/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/25/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/29/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/26/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 8/26/69

Reproduction 14" length economy breather cap hose for the 68 - 70 Cougar or Mustang.

This Gas Tank To Filler Pipe Hose reproduction fits the 67, 68, 69, and 70 Mercury Cougar. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

Both ends have 90 degree molded ends. Attaches heater core to water heater control valve.Replaces Ford Part #: C7ZZ-18472-CVAC.

High pressure hose from the insulator to the control valve. All correct ribbing, striping, and crimping. Has correct colored protective sheathing.  This hose is factory correct for the 1967-68 390, 427 and 428 & 1969-70 302, 351, 390 and 428. This hose can also be used to reroute the 1967-68 289 and 302 to the big block routing when paired with the other 3 hoses needed (C9OZ-3A319-A, C8ZZ-3A713-A, C7AZ-3A005-A) and the 69-70 power steering hose bracket (C7ZZ-3C510-A and...

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C.

This Pump to Value Outlet Pressure Hose is 100% correct for the 1969 small block, and will work for the 1967 or 1968 with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang /...

Reproduction hose that connects the oil cap to the air cleaner on cars equipped with the 289 engine. Replaces Ford Part number C6AZ-6A664-P

C8OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1968 X code 390-2V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - These molded and contoured hoses were designed to work with an original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake manifolds, valve...

NOS ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. Fits 1967-68 Mercury Cougar and 1966-69 Ford Mustang. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers,...

C6AZ-6A664-N Original used hose that connects the original PCV valve to the carburetor spacer plate. All 289-2V, 289-4V, 302-2V, and 302-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. Application for mid year 1966 through 1969 289/302 engines, including Cougar, Mustang, Falcon, Galaxie, Fairlane, Torino, Cyclone, Ranchero, and Comet. *Note - These molded and contoured hoses were...

Concours correct with ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers, and carburetor spacer...

Connects PCV valve to PCV transfer tube on the 390, 427-4V, and 428CJ. Inside diameter on one end is .45" the other end is .58". These should be tough to get on so that they will form a vacuum seal. Originally held on with wire clamps, we have those available here  Replaces Ford Part #: C8AZ-6A664-D. Fits Many 1966, 1967, 1968, 1969, and 1970 Mercury Monterey, Marquis, Ford Galaxie, with FE 390 Big Block Engines. We aren't sure why this hose was reproduced as shown. However it will...

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. One piece design, meaning it differs from the original separate two piece pressure hose set. Upper and lower pressure hoses were what came on the cars originally. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

Water By-Pass Hose with Autolite® logo and part number imprinted in white ink. Stamped with C2OE-8597-A. Replaces Ford Part #: C7OZ-8597

The 1967 - 1968 windshield washer kit varies slightly from the 1969 - 1970. Replaces Ford part #: C7ZZ-17543.

Used front drum brake hose bracket for any 1967-70 Mercury Cougar or Ford Mustang. Simple bracket bolts to the front aprons and holds the brake hoses stationary. Right and left side are the same.Ford part number C1SS-2082-C.

Reproduction 1/2" hose clamp, commonly used on the fuel lines. This clamp is smaller than the ones used on the power steering return line.

Reproduction Power Steering Return Line Hose Clamp for the 1967 - 1973 Mercury Cougar

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

Used to mate the headlight vacuum hoses together at the front cross beam under the core support. Notice it still has the remnant of green paint used to identify where the color coded hoses are to be placed. Cougar part number C7SZ-13A169-A.

Power Steering hose bracket insulator for both the small and big block brackets for the 1967 - 1970 Mercury Cougar and Ford Mustang. Replaces Ford part #: C7ZZ-3A609-A or C7ZZ-3609. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are things coming to? Where is...

CONCOURS radiator hose set, both upper and lower with C8ZE-8260-E and C8ZE-8266-E marked hoses. Used on both 20" and 24" inch radiators. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

New silicone radiator hoses for the 67 - 68 Cougar or Mustang with the 289 or 302 engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Used on both the 20"...

New silicone radiator hoses for the 69 - 70 Cougar or Mustang with the 390 or 428CJ engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Replaces Ford...

NOTE: Some Vendors show C8ZE for the upper hose, but C8WE is the correct stamping. These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each...

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear, both of which were suppliers to Ford Motor Co in the day. They are approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct for the specific application...

Reproduction Concours correct windshield washer hose with ribbed outer wall. Hose is 101" and is cut-to-fit. Tee connector not included, you can find it here. You can find the nozzles here.

No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually. Replaces Ford part #: C7ZA-430.

Replacement plastic vacuum tee for use on the 1968 Mercury Cougar headlight vacuum hoses. OEM Ford style replacement. Dimensions: 3/16 x 3/16 x 1/4

Replacement plastic vacuum tee for use on the 1968 Mercury Cougar headlight vacuum hoses. OEM Ford style replacement. Original Ford part number 373845-S.