1968 Mercury Cougar

Reproduction steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 - 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Good fit, includes all hardware shown. We've found that when using our reproduction drop down bracket (for those with headers), the bushings in this kit will rip and tear through the oversized hole, so you can also purchase the pair of the premium polyurethane bushings and the issue will go away. Otherwise you can go with our premium version boot kit of you need internal parts for the cylinder. Replaces Ford Part #: C6OZ-3C651-A ...

New old stock power steering ram cylinder boot and bushings. Fits all 1967-70 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C6OZ-3C651-A.

New old stock power steering ram cylinder boot, rubber boot only. Fits all 1967-70 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C3AZ-3C651-A.

This new reproduction power steering ram cylinder is good quality with almost no warranty claims. However, When you go to put your cotter pin in the castle nut you will often find it does not align perfectly which means you may have to drill it for a perfect fit. Keep in mind we will pay $30 in in-store credit for a clean original used ram cylinder so don't throw them away! RAM BOOT SOLD SEPARATELY. Replaces Ford Part #: C3DZ-3A540-A or C7ZZ-3A540-A. ...

This an original, rebuilt power steering slave / ram cylinder. It has not had a cosmetic restoration so it will show external dings, scrapes and general wear associated with a 50 year old part located on the bottom of a car. If you buy our reproduction ram do not throw away your core used ram as we often can give in store credit for the part. RAM DUST BOOT SOLD SEPARATELY.Replaces Ford Part #: C7ZZ-3A540-A.

Quality complete rebuild kit, includes all hardware shown. Premium flexible rubber boot that has vent holes, boot for elbow, and all hardware designated by an experienced rebuilder for completeness. This is the best known kit on the market.

Passenger side chassis bumper bracket for the rear axle. Passenger side as removed from a 1967-73 Mercury Cougar. Good condition bracket, road tested, but not salt road tested. Ships as shown, cut with generous margins around the original bracket.

Driver side chassis bumper bracket for the rear axle. Passenger side as removed from a 1967-73 Mercury Cougar. Good condition bracket, road tested, but not salt road tested. Ships as shown, cut with generous margins around the original bracket.

Reproduction rear axle outer bumper for the Mercury Cougar or Ford Mustang. These units mount on frame rail, are push in and two are required per car. Sold as a pair. Replaces Ford part # C6AZ-4730.

This 3 degree wedge properly sets the pinion angle for the drive shaft. This is a Cougar specific part which is needed due to the longer than normal rear leaf spring length. There are other wedges, but we seldom see them. This 3 degree marked wedge is the most prolific one. Feel secure in using these as a replacement.  Sold individually, two required per vehicle. Orientation: Narrow end towards the front of the car.

These are bolted to the rear frame rails and were used to tie the car down to the transporter for the journey from the factory to the dealer. The dealer was supposed to remove them and return them for a credit as instructed by the dealer. Notice the sticker on the rear license plate frame (decal is available in the decal section)? Many sets slipped through as the dealers often forgot or did not deem the small credit back worth their effort to remove. These are great for transporting your car...

Reproduction rear boot for your 67 - 69 Cougar or Mustang Midland power brake booster.

Reproduction Rear Bumper Guard Bolts & U Nuts for the 1968 Mercury Cougar 

Replaces Ford Part #: 379670-s

For deck / trunk lids it is all about rust under the inner rear lip... We still check it over good for excessive filler, correct contour on all the lines and hidden rust under the weather strip. We ship deck / trunk lids with several layers of thick cardboard and insure them for the full amount. Keep in mind shipping is free if you order at the same time as a hood, door or quarter panel. For those wanting a cleaner look on their 1967-68 Cougar a 69-70 deck / trunk lid will bolt right on with...

Late 1968 Mercury Cougar trunk lid, identified by having the large square hole for installing the trunk lock and latch parts. This style is hard to keep in stock, please see the 1967-68 version in the related section. Most often the problem with our Grade "B" deck / trunk lids is rust under the lip. We do not sell "rotted out" deck / trunk lids. Like the deck / trunk lid shown here you will be able to sand blast it and treat the rust so as to prevent it from spreading. We almost guarantee that...

Most often the problem with our Grade "B" deck / trunk lids is rust under the lip. We do not sell "rotted out" deck / trunk lids. Like the deck / trunk lid shown here you will be able to sand blast it and treat the rust so as to prevent it from spreading. We almost guarantee that at least "some" pin holes will appear after you have blasted the underside. Make sure to click onto our "after" shot to see what you should expect to see after you have bead blasted the underside of one of our "B"...

Used trunk or luggage compartment latch, fits all 1967-73 Mercury Cougar and many other Ford and Mercury cars. Comes with 3 bolts for mounting.Replaces Ford part number C5AZ-6243200-A.

Reproduction deck lid for the 67-68 Cougar. Exact reproductions of the originals, these deck lids are well fitting and are a perfect replacement for your old rusty lid.  Does not include hardware or lock cylinder, shipped bare. Here's the installation kit for these reproduction deck lids. Keep in mind that this is an oversized package and will most likely have to be shipped through truck freight. Expect to pay up to $250 in shipping charges. ...

Reproduction front diaphragm for your 67 - 69 Cougar or Mustang Midland power brake booster.Diameter 7 1/4"

[No Description Provided]

Passenger side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1967-69 Mercury Cougar and Ford Mustang.

Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...

Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...

Driver side, rear frame rail, from a 1968 Mercury Cougar. Full length, we cut so that there is some remaining metal on the edges. 1968 was the first year where the inside part of the frame rail has a large access hole for inserting the leaf spring bolt. The large access hole normally should have a plastic body plug to prevent debris from entering the frame rail. Ford part number C8WY-6510125-A.* Note - this item has dimensions in excess of 75 inches, and will ship as "Over- Size",...

Passenger side, rear frame rail, from a 1968 Mercury Cougar. Full length, we cut so that there is some remaining metal on the edges. 1968 was the first year where the inside part of the frame rail has a large access hole for inserting the leaf spring bolt. The large access hole normally should have a plastic body plug to prevent debris from entering the frame rail. Ford part number C8WY-6510124-A.* Note - this item has dimensions in excess of 75 inches, and will ship as "Over- Size",...

Fits any model that used the banded Midland-Ross booster. This Bakelite hub can be seen when you remove the dust boot. It is a very brittle fragile part that gets broken when you drop the booster, attempt to bleed the brakes with the engine running or install the wrong brake pedal.

Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.

Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Very limited choice of colors in grade "A", so please leave us a note in the comments section when ordering online and we will try to accommodate. Basket weave inserts in grade "A" condition will have all of the Mylar trim in place with no peeling or discoloring.

Grade B will have failing mylar chrome trim. Please list in the comments section of your online order what color you prefer and we will attempt to get you the desired color, limited to stock on hand.

Grade B will have failing mylar chrome trim. Please list in the comments section of your online order what color you prefer and we will attempt to get you the desired color, limited to stock on hand.

Very limited choice of colors in grade "A", so please leave us a note in the comments section when ordering online and we will try to accommodate. Basket weave inserts in grade "A" condition will have all of the Mylar trim in place with no peeling or discoloring.

Used vinyl cover for the rear interior panel found in the Mercury Cougar. Please let us know what color you need and we will try to accomodate.

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used driver side (left hand) rear interior panel in blue for the standard Mercury...

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used passenger side (right hand) rear interior panel in blue for the standard Mercury...

[No Description Provided]

[No Description Provided]

This is a great option for our foreign customers who want to save on costly shipping charges and have a good plastic backing but their vinyl damaged. It will take some patience to stretch and glue this to your existing panel but it is not that hard. We seldom will have your color in stock (unless is is black) but please choose your desired color and we will do our best to accommodate you. We carefully remove these from panels with broken plastic and only save the really nice examples.

Reproduction bare rear interior panels for any 67 - 68 Cougar. These are not complete panels, but rather just the plastic backing, so keep in mind that you will need to use your existing upholstery or have them re-upholstered. Good for Standard or XR7. Sold as a pair.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

New Old Stock Package tray speaker frame. Ford part number C8ZZ-18978-A, casting number C8ZA-18978-A.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

New old stock passenger side rear quarter panel extension. 1967-68 Mercury Cougar. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

This is the seal at the back of the booster on the Midland-Ross units.