1968 Mercury Cougar

C9ZE-9600-E Air cleaner base for the 1968 and early 1969 R code 428 Cobra Jet engine option. Additionally one way to identify this air cleaner is the dimple that clears the rear float screw found on the factory Holley carburetor. Early 1969 production is through 2/17/1969, after that date there was a vent added for automatic choke issues. About 16-3/8" inches in diameter. Ford part number C9ZZ-9600-E or C8ZZ-9600-A. Click on images to enlarge. ...

Good used tray that is not currently reproduced. Most people prefer the group 24 battery but for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting). Many that are not rotted have been cut to accept a group 24.

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Used Bell Crank from the Servo Assembly on any 1967-68 Mercury Cougar or Ford Mustang with speed control. Attaches to the Connector, via a Shaft, and Trunnion is attached. Ford part number C7ZZ-9B713-A.

C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate.  Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. Ford master part number C5OZ-7976-A. . ...

C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate. Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. NOTE * Grade B bell housing will have a chip or heavy scarring on the bottom, see photo...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C5DZ-6392-B. For use on 289 engines after 2-15-68. This bellhousing is only for use with the 157 tooth flywheel. This bell-housing also requires the use of clutch fork C8OA-7515-A. Shipped bare, no hardware or clutch fork. Replaces Ford part number C8ZA-6394-A.

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C6OZ-6392-B. The latest research shows that the casting number C60A-6394-B bellhousing may have been for 1966-68 Cougar, Mustang, Fairlanes and Comets with an 11 inch clutch disc.  Shipped bare, no hardware or clutch fork.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, levers and switches available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19A976-F Register and Control assy. (Bright Finish). Bright finish is Cougar, Ford Mustang bezels had black pebble grain or wood grain finishes attached. Ford casting number on...

This is a very hard to come by one year part used on both the Mustang and Standard - Decor level interiors on the Cougar. Whereas the plastic base and pad this attaches to can easily be modified from automatic configuration to manual, this part cannot. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks,...

Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.

Used bezel for the dual head rest found in the Mercury Cougar or Ford Mustang. This bezel measures 3 1/2" long and is correct for all 1968 models that use this part (including Shelby and Ford Mustang except the XR7 Mercury Cougar. Due to extra thick seat foam, the XR7 uses a taller bezel. Good used part with no peeling chrome or obvious cracks (may have hairline crack in threaded area). Ford originally had a special tool for installing and removing these guide sleeves. Ford tool division was...

Used bezel for the dual post head rest for the Mercury Cougar XR7. This bezel measures 4" long and is correct for the XR7. Due to extra thick seat foam, the XR7 uses this taller bezel. Good used part with no peeling chrome or obvious cracks (may have hairline crack in threaded area). Ford originally had a special tool for installing and removing these guide sleeves. Ford tool division was known as Rotunda. Down deep near the threads is a molded hex shape that allowed a tool to tighten without...

This is the correct horn panel bezel for all 1968 Cougar XR7 steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Unique to the XR7, identified by having the grey inserts. Please see related for standard model bezel.Ford part number C8AA-3D754-A. * Note - Will not work on standard model Cougar pads without removal of the inserts.

Used radio bezel Grade A used. For use on 1967-68 Mercury Cougar or Ford Mustang cars without console. 2-3 different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.

This was used only on the 1968 Mustang and standard Cougar, not for XR7. If you would like one that has been modified for an after market radio or you would not mind other minor blemishes (Or a broken ear) we have several that would save you money.Ford casting number C8ZB-6504567-C This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or...

Grade B 68 Radio Bezel for 1968 Mustang or standard Cougar. Holes often are modified for after market radio, might have broken upper mounting ear, pitting. Email for picture or detailed explanation of current stock on hand. Ford casting number C8ZB-6504567-CNeed some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The...

Reproduction pair of black seat belt buckle bezels for the Mercury Cougar, Ford Mustang, or Ford Torino. It is little details like these that often make the difference between first and second place at the show. 

Very rare find... A restored bezel will look fine but will never retain the sharp edges and matte black finish like this new in the box original Ford part.

This shift indicator will work on a 1967 or 1968 Cougar or Mustang equipped with automatic transmission. It comes with all items shown here.

They made three different versions of this plate for non console Mercury Cougars equipped with a manual three or four speed transmission. This part was not found on Mustangs as the Cougar often used a little "fancier" detail items in and out. Check out our video on rebuilding your shifter below: ...

Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. We consider the one remaining a B+ grade, due to pits in the chrome. This version is the one held down with 2 screws. Part number C7WB-7262-C is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-B, &...

Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. We consider the one remaining a B grade, due to pits in the chrome. This version is the one held down with 4 screws. Part number C7WB-7262-A is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-B, &...

This is for the person who does not want to modify the off-shore Mustang reproduction wheel lip mouldings we sell but do not have good cores for exchange for our premium set of restored wheel lips. Each one of these wheel lips will show some imperfections, mostly found on the inside where the wheel lip fastens to the wheel arch. The blems most commonly found on our less than perfect wheel lip mouldings may include multiple extra little holes drilled for mud flaps, "speckles" in the finish from...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang that is a high quality replacement part at a reasonable price. However, these off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the...

Good used working original heater blower motor for 67 - 68 Mercury Cougar and Ford Mustang.  The reproduction off-shore units may or may not prove to be as good of value as these good used original FoMoCo motors.  Keep in mind our used units carry a one year warranty and the new off-shore motors only have a 30 day warranty.  Also know that the mounting plate is included for free just by asking on the used motors. We never use the reproductions here at WCCC.  This unit...

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-5/16" oval holes. Sold individually, Usually 2 per car. Fits 1967-70 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378923-S.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

Inner front bolt, long length to clear sound deadener. Used in conjunction with a thick, gold spacer washer.

Rear seat belt bolt, four per car used in conjunction with two red washer / spacers. 13/16" hex head, 1-1/4 inch bolt with a 3/16 inch shoulder. Can be either smooth headed or have a Heavy or Light "A". There is another version of this same bolt with a smooth head and no markings.

Bolt for mounting thermactor smog pump to engine. Must be used in conjunction with thermactor alternator bracket and pump spacer. Bolt dimensions 3/8"-16 x 5.75" long.

Used Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang.Consists of: 1 bolt - 379384-S2 1 bolt - 378694-S 2 lock nuts - 33797-S2 set screws -  375694-S2

This is the Water Pump Bolt Kit for 1967-68 Mercury Cougar and 1965-68 Ford Mustang with the 289 or 302 engines without air conditioning. This kit includes the 11 bolts needed to mount the water pump to the motor.  This kit comes with an instruction sheet, and shows the correct placement of the bolts.

Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.

These reproduction hood latch catch bolts fit both the Standard and XR7.

Rear Valance Hardware kit contains 2 bolts, 2 clips and 2 nuts. "Almost" correct reproduction that functionally works great. Plated to prevent rust.See related items for a more complete fastener kit, which includes the pan head Phillips screws. Replaces Ford Part #: 372719-s100.

Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...

Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1967-70 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-753.

Used air compressor to intake manifold tubular steel bracket. Connects and supports the rear of the air compressor to the factory intake manifold. From what we can tell, there is no difference from 1967 to 1968 pieces.Ford part # C8ZZ-2889-A

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.

Reproduction bracket for mounting the rear axle flexible brake hose. From the factory, these brackets were welded in. Double check your placement for your particular year, when welding the bracket to your car. Has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Replaces Ford part number C7ZZ-2A051-A.

Used Bracket for mounting the Servo on any 1967-68 Mercury Cougar or Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C736-A.

The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Seldom in stock, we suggest the 1969 small block version. It is very close to this one. Please see related item. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

Reproduction power steering hose retaining bracket and retainer. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Bracket and retainer will work on 1967-70 Mercury Cougar and Ford Mustang with small block V8 cars with the correct  power steering hoses. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561693-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.