1970 Ford Mustang

This A/C evaporator drain hose is molded flex hose similar to the original, but it will need to be cut to the proper length. It is correct for 67 - 68 but can be made to work on 69 - 73. Replaces Ford part #: C7ZZ-19858-C or C8TZ-19858-A.

Replacement oil pan plug that is magnetized for collecting ferrous metal in the oil system. Replaces Ford part number C5ZZ-6730-M and D1AZ-6730-A. Fits all Ford engines 1967-73, including 6 cylinder, 289, 302, 351w, 351c, 352, 390, 427, 428, 429, 460.

New oil pan drain plug, Ford engine blue painted, with plastic gasket.  Looks correct, but has a different sized head than factory oil pan bolts. Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200,...

New Chrome oil pan drain plug, with plastic gasket. Has a different sized head than factory oil pan bolts.Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200, 240, 250, 289, 302, 351, 352, 410, 427, 428, and 429 engines 1965-1973. ...

New oil pan drain plug with zinc coating and plastic gasket. Fits all Mercury Cougar and Ford Mustang V8 oil pans 1967-73.

This shim, also referenced to as washers, goes in the clutch portion of the drive gearbox to properly adjust the friction. Three shims (plus a hand crank) were originally supplied with sunroof cars.

Only fits Ford Mustang 1969-70.

Reproduction power steering drop bracket for the Mercury Cougar or Ford Mustang. One must use this part when installing headers with power steering.  Because of the way this bracket hangs down, it will get bumped and bumped hard in time. Becasue of this we recommend considerning our premuim version of this bracket, as it is substantially stronger.

Installation of this bracket is easy but you will have to make a spacer to fit on the outside of the frame rail. Hopefully you bought this bracket first before you tore out the nut inserts in the frame. If not you will need to get them up for now. Then tap the bracket toward the the outside of the car and make sure the cross bolt lines up. Then measure the gap and make a spacer to fit. A half inch nut and a couple of washers usually work just fine. It's not necessary to get fancy with this...

Dual points conversion kit for all Ford V8 distributors. Big block and small block, parts included shown in pictures. Ford part number D0AZ-12A132-B.

Lower heater duct to floor outlet for Cougars or Mustangs with air conditioning. Used grade "B" part that will have minor defects. It will have cracks or chips. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered. Replaces Ford part number C9ZA-18C366-A.

C9ZA-18C433-C lower heater duct to floor outlet for Cougars and Mustangs without air conditioning. Used grade "A" part and may have one very minor defect. This part might have a small crack, but it will not have any broken or missing tabs. It's good, it's cheapish, you want it.

High Quality cloth wrapped heater duct hose. This is the correct length for most cars, but will need to be cut for proper fit in some applications. Hose diameter: 2 1/2"

This plastic A/C linkage arm for any 1969-70 Mercury Cougars and Ford Mustang. Over time they become very brittle and since the little vacuum actuator that they are connected to is so strong, they often break if any obstruction is encountered within the rectangular duct or around the linkage.You can find the retainer clips here, 2 required.Find the washer here, 1 required. ...

This plastic A/C linkage arm for any 1969-70 Mercury Cougars and Ford Mustang. Over time they become very brittle and since the little vacuum actuator that they are connected to is so strong, they often break if any obstruction is encountered within the rectangular duct or around the linkage.

Used driver side connector duct tube or elbow, attaches to driver side air conditioning register. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZZ-19B680-D and C9ZA-19C850-A.

Used passenger side connector duct tube or elbow, attaches to passenger side air conditioning register. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZZ-19C692-B and C9ZA-19C626-C

Used driver side connector duct tube, attaches to driver side air conditioning register. Fits center assembly. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZA-19B923-B, C9ZA-19B923-A, or C9ZZ-19B680-C.

Used passengerer side connector duct tube, attaches to passenger side air conditioning register. Fits to center assembly. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZA-19B737-C or C9ZZ-19B680-B.

Used driver side flex connector duct tube, middle of three duct tubes on driver side. This tube has a stapled flex hose included. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZZ-19C692-B and C9ZA-19C615-F.

Reproduction driver side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.

Reproduction passenger side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.

Clutch Lever Dust Boot for the 289, 302 and 351. Replaces Ford Part #: C6OZ-7513-C.

New old stock manual transmission shift lever boot. Attaches to the bell housing on FE big block cars. 1967-70 Mercury Cougar and Ford Mustang, 1966-71 Ford Fairlane / Torino. No comparison to the repro, this is much better.  Replaces Ford Part #: C6OZ-7513-A.

This reproduction is made from the original Ford tooling and is new to the market. Well worth the few extra dollars over the previous ones offered. Replaces Ford Part #: C6OZ-7513-A.

Fuel pump drive eccentric for Ford 351C engines 1970-74. Used eccentric from our wrecking yard. Includes inner and outer eccentrics, bolt, and washer. 2-1/2 inches in diameter. Ford part number D0AZ-6287-A.

Fuel pump drive eccentric for most big block Ford engines 1963-70. Including 352, 360, 390, 410, 427, and 428. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 3-3/8 inches in diameter. Ford part number C3AZ-6287-A.

This elbow is zinc plated for years of reliable service and is for 351, 390, and 428 engines. Replaces Ford Part #: D0AZ-18599-A.

Silver zinc finishDiameter 5/8"Fitting 3/4"

Elbow with water restrictor.

These bright beautiful reproductions replace those corroded and rusty originals that just look nasty. Replaces Ford Part #: C8AZ-18599-C

Replaces grommet in chrome oil cap with PCV valve. Inside diameter is 37/64". Replaces Ford part #: C8AZ-6892 or C8AZ-6A892-A.

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Reproduction emergency / parking brake cable return spring that goes underneath the car for the Mercury Cougar or Ford Mustang.

Reproduction emergency / parking brake assembly for the Mercury Cougar that is sold as a complete assembly. These units do look way better than our used crusty originals, but they will never hold up as well as original FoMoCo!Replaces Ford part # D0ZZ-2780-A

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for LH or DRIVERS side original part Ford number is C9ZZ-2A638-A.

Used parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for LH or driver side is C9ZZ-2A638-A. This unit is from a solid Western parts car, so you won't be getting one of those rusty East Coast units! Ford part # C9ZZ-2A638-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for RH or passenger side original part Ford number is C9ZZ-2A637-A.

C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.

Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A

Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.

There are multiple emissions decals available for the 351 Cleveland 2 barrel with an automatic transmission in 1970 for the Mercury Cougar or Ford Mustang. This sticker is printed with part number D0AE-9G485-S.

There are multiple emissions decals available for the 351 Cleveland 2 barrel with an automatic or manual transmission in 1970 for the Mercury Cougar and Ford Mustang.  This sticker is printed with part number D0AE-9C485-A.

Emission Decal for the 351 Cleveland 2 Barrel with an automatic or manual transmission in the 1970 Mercury Cougar or Ford Mustang. Printed with part number D0AE-9C485-AH.

Emission decal for the 351 Cleveland 4 barrel with an automatic transmission in the 1970 Mercury Cougar or 1970 Ford Mustang manufactured before January 1, 1970.  Printed with part number D0AE-9C485-F.