1970 Ford Mustang

Used steering column shroud or collar for any 1970 Mercury Cougar or Ford Mustang. These come in various colors, and have a rough texture. These will have some scratches in the surface, specify your desired color in the notes or comments section, but do know that black is in short supply. Ginger anyone?*Note does not include the retainer or clip, we cannot keep them in stock.Replaces Ford part numbers D0ZZ-3530-A.

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

This windshield wiper delay governor mounts to the driver side firewall. To find where this mounts on the firewall

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

This pair of reproduction convertible top hooks are beautifully chrome plated and features correct thread size. Looks close to original. These hooks are actually for 71 - 73 Cougars and Mustangs, but will work just fine on the 69 - 70.

C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.

D0ZE-B Applications: 1. *1970 Cougar with one of the **351 engines, with or without air conditioning. 2. *1970 Boss 302 Eliminator or Mustang. Fan description - 5 blades and 17-5/8 inches in diameter. Ford master part number C8SZ-8600-B and casting D0ZE-8600-B. This fan doesn't always carry a 1970 date, our current listing is dated J73 or Sept 1973. *Note - 1970 Boss2 and 1970 351 owners, some cars at the very start of 1970 may have used a C8SE-B marked fan. The C8SE-B fan is identical to the...

C9OE-H Application is for all 1969 428SCJ engines with the W code 4.30:1 axle ratio, and some instances it was found on 1970 428 super cobra jet engines. Fan description - 6 blade fixed pitch and 18 inches in diameter. Ford master part number C9OZ-8600-D. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C9ZZ-8600-C. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler...

C9ZE-6A360-A Very unique part and a component to the 'drag pack' option on the 428SCJ engines. This is an additional counter weight used on conjunction with the SCJ crankshaft, SCJ crankshaft balancer. Ford part number C9ZZ-6359-A.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

Tilt steering column cover plate for turn signal lever. Two versions, two different sizes of openings for the turn signal wand. Original used Ford part, plan on painting to match your steering column. Fits all 1970-71 Mercury Cougar, 1970 Ford Mustang, and other Ford/Mercury cars with factory tilt steering columns. Replaces Ford part number D0AA-9D793-AW.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

OEM Ford factory cowl brace as found on 1970 Mercury Cougar Boss 302 Eliminator and Boss 302 Mustang. Used item, not reproduction. Mounts with the lip up, towards the front of the car. Very limited supply.

Crankshaft oil slinger for all 429, 429CJ, 429SCJ, Boss 429, or 460 engines, the "385" series. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines.  Ford part number C8SZ-6310-A.

Reproduction of the very hard to find crossmember for any 67 - 70 Cougar or Mustang with the 390 or 428 engine and the C6 transmission. Replaces Ford Part number C7ZZ-6A023-B

Factory transmission support bracket for use on all 1967 - 1970 Cougars with 390-2V, 390-4V, 427-4V, 428 Cobra Jet engines and C6 automatic transmissions. Ford part number C7ZZ-6A023-B. This part weighs 3.5 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 3/4" on center and the passenger side is 3 1/2" on center. These "sometimes" will be stamped 390 on the inside.*NOTE* The key identifier on this C-6 unit that separates it from the...

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

D0ZZ-7528-D Equalizer bar or "Z" bar for 351 cubic inch Cleveland engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use. See the 1969 listing if you have a 1970 351 Windsor engine. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by...

Single cylinder head from 1970-71 Mercury Cougar with M code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 62.8 cc's. These are considered 'Closed Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 10.7:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-N. 4V in the...

Single cylinder head from 1968-70 Mercury Cougar with 428CJ engine with smog holes. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.09 and 1.65 inch valves, and the chambers measure out at 73-76cc's. With stock pistons, these heads will net an approximate compression ration of 10.6:1. Basic cylinder head number is 6090. These are the Cobra Jet exhaust manifolds with 16 drilled and tapped exhaust bolt holes. We won't have these in stock...

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. New Old Stock OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder. Thread pitch 1/2" x 20

These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder.Thread pitch 1/2" x 20 *Note - Export cars that did not require smog had a much shorter version of this plug installed at the factory. The plug shown here would be...

Used steel lower dash panel for all 1970 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. Grade B  = some pitting and or extra holes. Replaces Ford part number D0ZZ-6504320.

Here is another great product form Permatex. This decal and adhesive remover removes bumper and window stickers, tar, sap, bugs and other gooey substances. 

Here's the original "stereo" decal for the 69 - 70 door speaker grills. If you want to keep your car as original as possible, these are for you. These decals are made from aluminum, and as you know, they can get pretty flimsy after 45 years. We'll do our best to pick out good ones for you. You can get the sticker repro version here. SOLD INDIVIDUALLY. ...

Set of 5 reproduction firewall inspection decals. During final inspection, these decals where placed in different locations on the firewall / cowl area and one P decal between the weatherstrip and dash pad inside the drivers door jam. This decal set has the assembly line inspectors names stamped on them. These decals would have been used on cars equipped with Boss 302 and BOSS 429 engines.

Used switch for the rear defog or defogger fan on any 1969 Mercury Cougar, 1969 Standard Cougar, and 1969-70 Mustang coupe or hardtop. Original switch with attached wiring harness. Tested and working two speed switch. Comes as shown with chrome knob marked "DEFOG". Some examples may have minor pits in the chrome knob. Wiring marked C9WA-18C498-A. Excludes all convertible models and Mustang fast backs.Replaces Ford part number C9ZZ-18578-A.*Note - is not technically correct for 1970 Mercury...

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1969 - 1972 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford master part number C9OZ-7A020-A, Ford casting # C9OP-7A020-A.

Used dipstick tube for the Mercury Cougar or Ford Mustang equipped with the C6 transmission. The C6 option can be identified by code "U" on your door data plate. Ford part # D0ZZ-7A228-A.

Original dipstick tube. Application 1970 - 1972 Mercury Cougar or Ford Mustang with FMX automatic transmissions, code "X" on your door data plate. These have a little longer tab than the 1969 FMX dipstick tube.Ford master part number D0OZ-7A228-C.

As seen in our YouTube video, this is a representation of the used, rebuilt and reproduction parts that we recommend you purchase to convert to disc brakes. If you do purchase this package we will insist on speaking with you prior to shipping as you may want to substitute parts based on what year your car is, manual or automatic and what style booster you prefer. Also know that if your car already has power drum brakes we will be able to reduce the price substantially as no booster or pedal...

Used Distributor / 351C-2V / for the 1970 Mercury Cougar / 1970 Ford Mustang Ford part number D0AF-12127-V  

Used distributor for the Mercury Cougar or Ford Mustang that is equipped with the 351 Cleveland 2V engine.

Used core distributor for 1970 Mercury Cougar and Ford Mustang with M code 351C-4V and either 3 or 4 speed manual transmission. Core distributors will have correct stamping of D0OF-V. Original Ford part number D0OF-12127-V. 351 Windsor engines use a smaller distributor gear (about 1-1/4"), Cleveland.distributor gear is about 1-7/16" in diameter.

Used core distributor for 1970 Mercury Cougar and Ford Mustang with M code 351-4V and automatic transmission. Core distributors will have correct stamping of D0OF-Z, 351 Cleveland Engine. Original Ford part number D0OF-12127-Z.

Used Distributor / 351W-2V for the 1970 Mercury Cougar / 1970 Ford Mustang Ford part number D0AF-12127-H  

Used core distributor for 1970 Mercury Cougar and Ford Mustang with 428 Cobra Jet and 4 speed manual transmission. Also fits 428SCJ engines with 4 speed stick. Core distributors will have correct stamping of D0ZF-C. Ford part # D0ZF-12127-C.

Used core distributor for 1970 Mercury Cougar and Ford Mustang with Q code 428CJ and automatic transmission. Core distributors will have correct stamping of D0ZF-G. Original Ford part number D0ZF-12127-G.

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port with added vacuum fitting as shown. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later...

Used core distributor for 1969-70 Mercury Cougar and Ford Mustang with G code Boss 302 engine. Core distributors will have correct stamping of C9ZF-E. Original Ford part number C9ZF-12127-E. No vacuum advance included. Current distributor has a date of 9J8, or Sept 8, 1969. Early 1970 build date.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Silicone and fasteners, everything needed for installation of our seat divider panel.

Heater door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater door allows air to pass over the heater core in the A/C box. This is the smallest door in the A/C box, and the one subject to the most damage from moisture. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...

Power window door and main harness from a 1969 Mercury Cougar and 1970 built before 2/2/1970. Tested and inspected and ready to install. Does not include any of the other power window harness segments, i.e. passenger side door, rear windows, or under hood segments. Switches also not included. Does not fit late 1970 cars. This harness only works with the small style power window bezel, which was used before February 2, 1970.Replaces Ford part C9WY-14631-A and D0WY-14631-A.

NOS (left hand) bolt in clear door glass for the Mercury Cougar or Ford Mustang. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is not a tint...