1970 Ford Mustang

Upholstery components have an ETA of 5 - 9 weeks.A few Eliminators came with standard interior, but convertibles did not come factory with a standard interior. These sets feature horizontal stitching and correct grain of vinyl. Below is a set of pictures of this set stretched on a bucket seat frame.*NOTE* This product will take 4 – 6 weeks for delivery.               ...

Upholstery components have an ETA of 5 - 9 weeks.A few Eliminators came with standard interior, but convertibles did not come factory with a standard interior. These sets feature horizontal stitching and correct grain of vinyl. Below is a set of pictures of this set stretched on a bucket seat frame.*NOTE* This product will take 4 – 6 weeks for delivery.               ...

Great option for international customers. Light weight, and all you need is a PC or laptop, and you can plug this drive in and access all the same information that you'd find in the full sized shop manual books.

This used conversion kit includes the controller and switch to convert your standard two speed wiper system over to delay wipers.Controller part # C9ZB-17C476Switch part # D0ZF-17A553-B, MPC # D0ZZ-17A553-A

This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A

Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.

Multiple uses.5/8" from bend to center hole.

Replace FORD Part #: C8WB-17093-B

Replaces Ford Part #: C8WB-17093-D.

Correct for the 1969 Eliminator SS wheel. Replaces Ford Part #: C9WB-17093-B

This decal goes on the tire jack itself.

Used jumper wire with correct ends for doubling back on the tachometer leads from the under dash harness. Works for all generations 1967-68, 1969-70, and 1971-73 Ford anything and Mercury, and Mercury Cougar with factory tachometers. If your tachometer goes bad, you will not start or keep your engine running. Good for bypassing tachometers for testing and getting home. Keep in your glove compartment or tool box.

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. This jumper can also be used to repair bad stop light connectors on 1967-70 Cougars and Mustangs (and other Fords) by cutting off the male end and splicing it...

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. Ford master part numbers: C5AZ-14489-C, C8ZA-13K408-A and C8ZZ-13K408-A

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

Key reminder buzzer for 1970-71 Mercury Cougar and Ford Mustang. Also used on 1970-72 Lincoln MKIII and Thunderbird. Can also be stamped DOAB-13150-B, DOAB-13150-E, and DOAB-13150-F. Ford master part number D0AZ-13150-E. All buzzers are bench tested prior to shipping.NOTE: This buzzer is for ignition key reminder with two posts. The four post ignition / headlight buzzer can be found here.Click on images to enlarge. ...

Key reminder and headlamp buzzer for 1970 Mercury Cougar and Ford Mustang. Also used on 1970 Lincoln MKIII and Thunderbird. Ford master part number D0WB-13150-A. All buzzers are bench tested prior to shipping. NOTE: This buzzer is for ignition AND headlight reminders with four posts. The two post ignition buzzer can be found here. Click on images to enlarge. ...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the ignition / door key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

This reproduction rod is made from stainless steel and weighs slightly more than the original.

This rod is correct for the 351 Cleveland 2V only and is approximately 27". A red paint daub was found on this rod, by trying to expose it with steel wool, it was almost erased. This would explain why we rarely find rods with the original paint daub in place. Slightly shorter than the 4V rod and has a lower connection point to the carburetor.

Exact reproduction of this one year only rod is correct for the 351 Cleveland 4V and is approximately 27". This rod originally had a light blue paint daub near the carburetor. It is a little longer than the 2V rod and connects to the carburetor at a slightly higher point. This reproduction rod is made from stainless steel and weighs slightly more than the original. Replaces Ford Part #: D0OZ-7A187-C

This one year only rod is correct for the 351 Cleveland 4V and is approximately 27". This rod originally had a light blue paint daub near the carburetor. It is a little longer than the 2V rod and connects to the carburetor at a slightly higher point.

Unique to the 1970 351w with FMX. Originally came with a light blue paint daub at the top.

Exact reproduction made by Daniel Carpenter. Injection molded black plastic. Very nice. Much thicker and more durable than other reproductions. Sold as a pair. Replaces Ford Part # : C9ZZ-6502344/5

Used wiper control knob for lower dash. Plastic knob, will show some minor wear. Ford part number D0OZ-17513-A.

Chrome and black knob just like the original.NOTE: This knob is correct for 1969. It will fit on a 1970, however the orientation of the pointer will be off. You can find a good used 70 knob here. Replaces Ford Part # : C9ZZ-17513

Nice clean set of four used radio knobs for your 69-70 Mustang or Cougar. No peeling or cracks. The inset picture shows the used next to the new from the backside. The reproductions are shown on the right. Whereas the repros are nice, the originals are still superior. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. White plastic reproduction spacers available here. The white...

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650509-K. Casted Pot Metal with Engineering # C4ZB-7650535-C

Used driver side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired.  Ford part number C4ZB-7650535-C.

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650508-KCast Pot Metal with Engineering # C4ZB-7650534-C

Used passenger side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired. Ford part number C4ZB-7650534-C.

Used stamped steel lateral support bracket for all 1970 Mercury Cougars and Ford Mustangs with the 351 Windsor or Cleveland engine. Ford part # D0OZ-2888-A*NOTE* - Excludes all 1969 351 Windsor engines.

Used steel lateral support brace for Cougars and Mustangs with the 390-2V, 390-4V, or 428CJ FE engines. Identical to the 1970 FE lateral bracket except 1970 versions have square nuts on the reverse.Ford part # C8AZ-2888-A

Used steel lateral support brace for Cougars and Mustangs with 428CJ FE engines. Identical to the 1968-69 FE lateral bracket except 1970 versions have square nuts on reverse. Also the same bracket for Ford passenger car 390 up until 1971.Ford part # D0AZ-2888-B

Reproduction Legendary Series GT5 Alloy Wheel. This updated design was created using state of the art casting technology for superior strength and precision. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium...

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with natural aluminum accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...

Reproduction Legendary GT9 series aluminum wheel in the charcoal finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...