1970 Ford Mustang

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

This is a good used speedometer cable from a 1969 - 1970 Mercury Cougar with a FMX transmission. The cable housing has no burns and the fragile plastic squeeze clip that fastens it to the back of the speedometer is not broken. Keep in mind that some 1970 models use a two part cable. This cable will work in place of the two part cable seen on some 1970 cars. This cable measures 58 1/2" at its very most outer ends.

New manufactured 4 speed, speedometer cable for use drag pack 1969-70 Mercury Cougar and Ford Mustang. Has correct end for fitting onto factory gear reducers. Drag pack ring an pinion ratios were 3.91:1 and 4.30:1, which needed a mechanical gear ratio reducer in addition to a normal speedometer gear.Cable Length: 70"

According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. https://www.428cobrajet.org/id... This is a part that we will probably never...

According to the Master Parts Catalog (MPC), Early (before Jan 31, 1969) Cougar with a 3.91 or 4.30 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. Also found on 1970 4 speed Mercury Cougar and Ford...

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. Replaces Ford Part #: C8ZZ-17294-A.

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. This is a part that we will probably never have on hand, but would love to document. If you have one of these adapters, we would be interested in being able to put detailed pictures of it on this listing. Please let us know. We hope to have a reproduction of this adapter...

Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.

Fits 1968 (mid year change) through 1976 Cougar and Ford forks - All engines.Includes:1 Spring Clip2 RivetsReplaces Ford Part #: C8AZ-7B516-A.

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1970. Produced by Motor Wheels, early ones had riveted centers, changed to welded centers in 1969. Specify in the notes section if you have a preference, we seem to have mostly welded ones at the moment. Have a bent or damaged wheel? Don't...

Used 14x7" stock stamped steel wheel for the Mercury Cougar and Ford Mustang / Torino. Rare seldom seen size most commonly found on a Ford Torino. These were offered from 1971 through 1973 on the Cougar and 1970 - 1973 on the Mustang and Torino. Have a bent or damaged wheel? Don't have a spare? Total width is 8" with a 4" backspacing. Various conditions and subject to availability. Used 'as is', wheel as found in the wild.Ford part # D0OZ-1007-B.

Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K

1970 Mercury Cougar / Ford Mustang columns were a weak design from the factory. We find that all the columns we get have some degree of excessive play, some will not even hold position. The design was improved upon greatly as the years went by and spending a little more on an updated / rebuilt one is well worth the investment. This is a 100% complete column with key and all parts needed to convert from a fixed to a tilt column. You can use your existing plastic plastic color keyed collar and...

These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box... Our boxes are rebuilt here in the USA at a one man shop where this is all he does. Our boxes are done by a...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

These are cracked core wheels as taken from a parts car. The Center pad is not included and you can count on the rubber switch being rock hard. This wheel is for restoration purposes and we cannot guarantee that we will have all colors in stock at all times. The three wheels shown here are random examples and are not what you will actually be getting when you order. Most colors in stock, call for color, or leave desired color in the comments section of your order. ...

This restored three spoke, rim blow steering wheel was used on all Cougars 1970-73 except the Cougars equipped with standard interior or on rare occasion the 1973 Cougars that came with the rare 2 spoke leather wrapped wheel. The Cougars equipped with standard interior used a two spoke wheel with the horn button located in the center pad. If you choose to send in a core for exchange it will need to be a clean one as we will not restore steering wheels that have huge cracks, severe UV damage or...

This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...

The horn switch is embedded in this soft part. Limited colors on hand, call for availability. White plastic is prone to cracking due to shrinkage and age. Most will have a crack or two. Ford part number is D0ZZ-13915-A

Decent offshore reproduction but nothing beats the fit and finish of a good original FoMoCo part. Checkout our used as we have multiple colors in stock. This repro pad only comes in black. Replaces Ford part number D0AZ-3623-A.

This used grade "A" stone deflector is a one year only (1970) design is getting rather hard to come by in grade "A" condition. Often we do not have this part in stock in grade "A" condition so we suggest looking at our grade "B" stone deflectors as they have very minimal damage and are not hard to repair on your own. This unit is also know as a bumper filler, rock guard, or filler panel.Ford part # D0WY-17779-A.

Very good used 1970 Cougar or Mustang console storage compartment. Sometimes called a 'well'. This is the "before 12/1/69" version, without cigar lighter and button or latch. According to the MPC there were three versions: prior to 9/2/69, 9/2/69 to 12/1/69, and after 12/1/69. These originally came in 6 different colors - black blue red ginger green tobacco. Notice that this part does not have the cigar lighter? In 1970 the cigar lighter was moved to the dash. Ford stuck the cigar lighter into...

Very good used 1970 Cougar or Mustang console storage compartment. Sometimes called a 'well'. According to the MPC there were three versions: prior to 9/2/69, 9/2/69 to 12/1/69, and after 12/1/69. These originally came in 6 different colors - black blue red ginger green tobacco. Notice that this part does not have the cigar lighter? In 1970 the cigar lighter was moved to the dash. Ford stuck the cigar lighter into the position previously occupied by the ignition switch in 1969...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Here is our NOS vacuum valve assembly which is fairly hard to come by these days. This unit is for Mercury Cougars or Ford Mustangs with integral or factory air conditioning. This part is good until an assembly date of 1/3/1972 and, if you want, we also have good used pieces in stock for your Coug or Stang as well. Ford part # C9ZZ-19B888-A.

Backup lamp switch that mounts to the factory 3 speed shifter linkage. 69 70 71 72 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-947. Used up until 5-15-1972. Tested and working switch with wiring and plug.*Note - 3 speed switches are different than the manual 4 speed switches.

D0ZZ-15520-A Backup lamp switch that mounts to the factory 4 speed shifter linkage. 70 71 72 73 Mercury Cougar and Ford Mustang applications. NOS Autolite or Motorcraft switch number SW-943. Used with OEM installed Hurst Competition shifters. *Note - 4 speed switches are different than the manual 3 speed switches.

D0ZZ-15520-A Backup lamp switch that mounts to the factory 4 speed shifter linkage. 70 71 72 73 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-943. Used with OEM installed Hurst Competition shifters. *Note - 4 speed switches are different than the manual 3 speed switches.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

New Old Stock brake light switch for the Mercury Cougar or Ford Mustang equipped with  disc brakes. This switch fits the 1969-70 for power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C9ZZ-13480-B.Fits: 1969 Mercury Cougar (power disc)1970 Mercury Cougar (power disc)

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

Tested and inspected neutral safety switch for the C-6 transmission installed in 1970 - early1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971.Look for a transmission code of U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: D1ZP-7A247-AA, or D0ZZ-7A247-B, SW 920.

Tested and inspected neutral safety switch for the FMX transmission installed in 1969- through early 1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971. These mount in the shifter bucket, see your shop manual for installation adjustment.Look for a transmission code of X on your door data plate. Replaces Ford Part #: C9ZA-7A247 or C9ZZ-7A247-C, SW 903.

New old stock power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch. Stamped C8AB-14529-A. This is the 1 tab switch. However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.

NOS fixed column turn signal switch for the 1970 - 1972 Mercury Cougar or Ford Mustang.Ford part number D2AZ-13341-CNeed help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

NOS fixed column turn signal switch for the 1970 Mercury Cougar or Ford Mustang. Ford part number D0ZZ-13341-A or D0ZA-13B302-C. Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. Replaces Ford Part #: D0ZZ-8592-A.

Cable length 22.83 inches long, identified by a plastic ball shaped end attached onto the pedal side of the cable. Must be used with a 1970 accelerator pedal shaft. This is an unbroken part. Notice there are two versions, one has plastic covering the cable and the other has an exposed cable.