1970 Ford Mustang

Tested and working used pair of Hi and Lo tone horns. 1969-70 Mercury Cougar and Ford Mustang used part number C9ZF-13802-C and C9ZF-13801-B. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.

Aluminum flexible tube that connects the vapor canister to the air cleaner. To give this the look of the originals that had a black paper exterior coating you can spray paint it flat black. If anyone knows of a source to buy the original paper coated foil tubes we would like to hear from you. Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct.3ft long 7/8" O.D. 3/4" I.D. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A...

Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 1/26/70

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/67

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/28/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 12/5/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/25/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/29/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/26/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 8/26/69

Reproduction 14" length economy breather cap hose for the 68 - 70 Cougar or Mustang.

This Gas Tank To Filler Pipe Hose reproduction fits the 67, 68, 69, and 70 Mercury Cougar. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

High pressure hose from the insulator to the control valve. All correct ribbing, striping, and crimping. Has correct colored protective sheathing.  This hose is factory correct for the 1967-68 390, 427 and 428 & 1969-70 302, 351, 390 and 428. This hose can also be used to reroute the 1967-68 289 and 302 to the big block routing when paired with the other 3 hoses needed (C9OZ-3A319-A, C8ZZ-3A713-A, C7AZ-3A005-A) and the 69-70 power steering hose bracket (C7ZZ-3C510-A and...

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C.

This Pump to Value Outlet Pressure Hose is 100% correct for the 1970 small block. This is the upper portion that connects to the one year only 1970 pump found on the 351c, 351w and BOSS 302 equipped cars. Like the originals, this is part one of a two part hose. This hose has industrial high pressure fittings that are much higher quality than those available by most Cougar / Mustang parts dealers. Replaces Ford Part #: D0OZ-3A319-A.

Concours for 1970 351C-2V and 351C-4V with correct ink stamped Ford script, 17 1/2" long including the 90 degree bend. Connects PCV valve to carburetor spacer plate. Other parts houses list this as a 71-73 but the 71-72 is 25" long (so it can reach to the front of the driver side valve cover) on both the 2V and 4v 351 Cleveland and this hose will not reach. This will work for the 1973 Q-code 351C-4V as the 73 mates to a metal tube and is only 11".This hose was originally installed from the...

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

Water By-Pass Hose for 351W engines with Autolite® logo and part number imprinted in white ink. Stamped with C9OE-8597-D. This would be correct for Mustangs and other Ford or Mercury with 302 engines in 1969. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 10/22/69

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 12/15/69

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 2/12/70

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 5/2/69

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 6/6/69

Reproduction hose and clamp kit for the brake booster on the 1970 Cougar or MustangDate code 8/18/69

The 1969 - 1970 windshield washer kit varies slightly from the 67-68.Replaces Ford part #: C9ZZ-17543.

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

Power Steering hose bracket insulator for both the small and big block brackets for the 1967 - 1970 Mercury Cougar and Ford Mustang. Replaces Ford part #: C7ZZ-3A609-A or C7ZZ-3609. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are things coming to? Where is...

Exact fit, not generic 'One Size Fits All' hoses. Quality high pressure fittings. Contains both the upper and lower Hydraulic Hose for a 1969 or 1970 Mercury Cougar or Ford Mustang Convertible Hydraulic Cylinder.

These are the best CONCOURS radiator hoses on the market. Made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. Features special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct including Autolite logo. Hoses are also approved by Ford Motor Co. Replaces Ford Part #: D0ZE-8B273-B &...

Reproduction Concours correct windshield washer hose with ribbed outer wall. Hose is 101" and is cut-to-fit.Tee connector not included, you can find it here.You can find the nozzles here.

No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually. Replaces Ford part #: C7ZA-430.

Reproduction turn signal / parking light housing for the 1969 Mercury Cougar or 1969 - 1970 Shelby.  2 required per car, left is same as right. Includes mounting studs, socket, bulb and wiring.

Reproduction turn signal / parking light housing for the 1970 Mercury Cougar or 1970 Mach 1.  2 required per car, left is same as right. Includes mounting studs, socket, bulb and wiring.

Used hub cap center for the deluxe Rallye type hub caps as found on certain 1970 Mercury Cougar, Ford Mustang, or Torino, etc. Center only with fake lug nuts. These are held on with 8 hex screws, and only fit the Rallye style of hub caps. Should fit 14x6 and 14x7 wheels. Small diameter center caps with specific color images, not included. Silver or Argent accent colors. Most likely will need a fresh spray of desired color. Limited to stock on hand.  Ford number D0ZA-1A041-A on...

Used B grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone 1970 Mercury Cougar Eliminator / Cyclone 1971 Mercury Cougar / Cyclone 1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford...

Reproduction dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. There are no less than three versions of this reproduction unit on the market. This one, in my opinion, is the best option. The hue is not as brilliant as the original, but a very nice cap for the fit and finish that it offers. We have trim rings available too! Check out our video on Legendary Wheels below: NOTE: These are for use on the Legendary Series Eliminator wheels Fits:...

The POGO Stick works just like the larger Hustler stick but is much easier to ship. If you need more leverage you can just add a pipe for leverage. We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Check out our video below: ...

Connecting to the Convertible Frame Lift Lever and the Convertible Hoses, the Convertible Top Hydraulic Cylinder creates pressure from the fluid transferred by the hoses. Each Hydraulic Cylinder consists of light-weight aluminum casing, a durable steel rod, and includes all bushings and gaskets. Part is made through innovative engineering and rigorously tested to provide you with the best in functionality and long-term dependability.  Precisely crafted with high grade materials...

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade A cans are far and few between as often folks like to use a pry bar as leverage to over tighten their belt. These cans will usually have...

D0ZZ-3A697-B Application is 1970 351 engines. Originally found on pumps with tag number HBA-CC. Has the off centered, high pressure port. Our Grade A cans are far and few between as often folks like to use a pry bar as leverage to over tighten their belt. These cans will usually have some shelf wear but nothing major. If it shows out of stock please hit the "notify me" button and we will email you when one gets checked into our stock. ...

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to...

D0ZZ-3A697-B Application is 1970 351 engines. Originally found on pumps with tag number HBA-CC. Has the off centered, high pressure port. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to look like grade A

Grade A Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps. Our...