1970 Ford Mustang

Quality recreation made from original parts. Decent reproduction, slightly different than the original Ford version. The noticeable difference is the lack of square notch in the slop joint. Ford part of C8OZ-9A626-C. This snorkel comes to you in primer.

For all 1968 through 1970 R and Q code 428CJ and SCJ air cleaners. Snorkel has the opposite jog than 390GT snorkels. This one jogs towards the rear of the engine. Originally this snorkel should have had an ink stamp of C8OF-9A626-A or -B. Ford MPC number C8OZ-9A626-C.

Although these are considered reproductions, they are actually put together from multiple parts of original excellent condition used snorkels. And, since there are multiple colors of Ford Blue, the supplier is leaving them as unpainted.Application would only be for 1970 Boss 302 Eliminators and Boss2 Mustangs. Ford part number D0ZZ-9A626-B.

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Replaces Ford Part # D0ZA-A

Reproduction Space Save Tire Instructions Decal for the 1968 - 1973 Mercury Cougar / Ford Mustang

Reproduction Space Saver Spare Recall Postcard for the 1968 - 1971 Mercury Cougar / Ford Mustang

Aluminum spacer used on 289/302/351 engines for mounting the alternator. Length is 1-5/8 inches long, mounts between the alternator and the cylinder head.

Alternator spacer bracket for all 351 engines. 1970-73 Mercury Cougar and Ford Mustang among others such as Torino, Cyclone, Galaxie, LTD, etc. Aluminum material, 2-1/4 inches long, with a 7/16" hole. Sometimes solid and sometimes open along the side. Ford part number D0OZ-10A370-A.

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. New manufactured.

B8AZ-6359-A Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. Used spacer, will show a little wear from the outside seal. 

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Reproduction 384542-S2 Power steering pump adjusting spacer for use without air conditioning. For all 1970 and later Mercury Cougar or Ford Mustang with 302 or 351W engines. Spacer dimensions: 7/16" I.D. and 3/4" thick.*Note - 351C engines use a 1/2 inch spacer.

Reproduction  Lower Windshield Moulding Center Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Used spacer for the lower windshield moulding

Reproduction  Lower Windshield Moulding Fender Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

We claim that in time every nut bolt and clip will be documented on this site! Here is yet another tiny little, one year only trivial part that only the most detailed enthusiast will even care about. This little part is designed to space the column cover away from the metal lower dash so as to prevent dash squeaks. They are left natural, never painted (the one shown has surface rust). Two are required per car, they are sold individually. These little parts are often missing and of course not...

Reproduction engine block spacer plate for 1969 1970 351 engines FMX (code X) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too.  Replaces Ford part number D0AZ-7007-A.

Factory engine block spacer plate for 1969 1970 351W and 351C engines FMX (code X) and C6 (code U) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions. There are probably two versions of this plate, we believe the the 1969 version did not have the indentations. Replaces Ford part number D0AZ-7007-A.

1967-70 Cougars with any FE engine (390-2V, 390-4V, 427 GT-E, 428CJ, or 428SCJ) and with C6 automatic transmission or manual transmissions.  Ford part #: C3AZ-7007-D.

Early version of the FE engine / Transmission spacer plate. Has 1 medium sized hole instead of 3 smaller holes above the crankshaft. Originally was for either automatic or manual. Ford part #: C3AZ-7007-A.

Reproduction engine block spacer plate for 69 - 73 Cougars or Mustangs with 351 engines and 3 or 4 speed manual transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions.

Pair of reproduction sway bar mounting spacer plates, to be used with the 15/16 inch sway bar found on 427 4V / 428CJ / BOSS 302 cars.Mounts between the bracket and the frame mount.

This spring does NOT have correct spring finish or tension, but will work fine if you want to save a few $$$. Above is a comparison to this reproduction which is carried by other retailers, compared to our spring which is very close to the correct finish, length, and tension. Replaces Ford Part # : C8ZZ-17119-A ...

Original space saver tire from a 1968-70 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-70. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.Just the tire, perfect for someone who has a dated wheel.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...

Original space saver tire marked B.F. Goodrich F78-14. Display only, it can not be inflated. Rear side wall has damage. From a 1970-71 Mercury or Ford. Bolt pattern is 5 on 4-1/2. Not sure if it has ever been inflated, it is collapsed as shown.  Just looking for a space saver spare? Has the good tread design, single fill valve stem, but with damaged sidewall. This is it, it looks the part to those that casually look in the trunk of the car at a car show. Tread is a...

Original space saver tire marked F78-14 B.F. Goodrich, from a 1970's Mercury or Ford. These were optional in 1968-73. It has the smaller hub size and single valve stem. Never inflated condition. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire. *NOTE* Does not include inflator bottle and valve caps are usually missing. ...

10 5/8" Spare Tire Mounting Bolt. Not 100% correct, but close replacement for the 1969 - 1973 with the 10 3/4" spare tire mounting bolt. Replaces Ford Part #: C8ZZ-1448-A, D0ZZ-1448-A & D1ZZ-1448-A.

Correct Autolite 24 spark plugs for all 1970-73 351 Cleveland engines. This is what Ford installed originally from the factory. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

Correct Autolite 45 spark plugs for all 1967-73 289/302/351W/390/428CJ engines. This is what Ford installed originally from the factory. BF32 crosses over to this spark plug. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.

Concours correct Autolite spark plug wires for any 1970 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q69 (second quarter 1969) on the 7mm wires. Orange spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1970 Mercury Cougar Eliminator or Ford Mustang with 351W engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q69 (second quarter 1969) on the 7mm wires. Black spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1970 Mercury Cougar or Ford Mustang with 428CJ engines with thermactor smog systems. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q69 (second quarter 1969) on the 7mm wires. Orange spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1969-70 Mercury Cougar Eliminator or Ford Mustang with Boss 302 engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q69 (second quarter 1969) on the 7mm wires. Orange spark plug boots on this set.