Wanted!
Buy
Details
Availability: Out of Stock
Item #: 11845 -
This dealer installed kit was designed to fit many FoMoCo products. These were most commonly mounted on the driver side rear panel. They were taller than the standard antenna so mounting them on the driver side would protect them from low lying branches and other obstructions that more often come in contact with the passenger side of the car. This is one RARE unit for sure! ...
Wanted!
Buy
Details
Availability: Ships Direct from Supplier (Except International)
Item #: 19899 -
Reproduction "A" pillar repair panels for your 67 - 68 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 11810 -
Replacement radiator cap for the 1967 - 1973 Mercury Cougar or 1967 - 1973 Ford Mustang. This radiator cap releases pressure when the pressure exceeds 13 pound of pressure.
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 33073 -
This big book measures 18" x 13" x 3" and weighs 8 pounds. It's a must have if you are serious about electrical or vacuum work on the Cougar, Thunderbird, Mark III, Montego, Fairlane, Maverick, Cyclone, Bronco, F100, Torino, Mustang or other Ford products products from 1968. Condition is used and will have a few pages that have torn away from the rings. Form 7795P-68 Course 13003 and 1760Volume 68 S4
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 33063 -
NOS Ford service training manual on diagnosis of charging system problems. This booklet is a guide to diagnosis of the alternator, regulator, battery and wiring issues. It contains diagnostic procedures and self instructional tests and was meant to be used as a reference guide for the "charging system videotape (video tape not included). 16 pages long with tests and answers.Issued Dec. 1974, # 365-240
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 10634 -
New 2.5 amp Buss style glass tube fuse for the Mercury Cougar or Ford Mustang. This fuse was used for 1967-68 only and is used for the instrument panel, clock and ashtray lights. This unit measure about 5/8" long and is Sold individually.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 30991 -
Miniature light bulb for any 1967-68 Mercury Cougar or Ford Mustang with the door ajar feature. Original equipment GE 256 light bulb. This is a flashing light bulb. It has a metal strip that heats up and breaks contact for a flashing effect. Starts out with the bulb on, and eventually starts flashing over a period of a few seconds.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 10560 -
Concours correct Autolite spark plug wires for any 1968 Mercury Cougar or Ford Mustang with 289 or 302 engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q67 (second quarter 1967) on the 7mm wires. Black spark plug boots on this set.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 15249 -
Small block dipstick tube for the 1968 Cougar and Mustang. Nice chrome finish to catch the eye. Will also fit on 1969 Mustangs with a 302 engine.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41042 -
Reproduction intake manifold nut for the 289 or 302 on the 1968 Mercury Cougar and Ford Mustang (and possibly other Ford / Mercury cars). 5/16-18 X .72 X .33 zinc free-spin flanged nut. Sold individually. Replaces Ford part #: 374031-S
Wanted!
Buy
Details
Availability: Ships Direct from Supplier (Except International)
Item #: 17763 -
Exact Reproduction 289 Hi-Po Main Cap Set offered by Ford. They are cast and machined here in the USA from the original Ford blueprints. A set consists of caps numbered 1- 4 and requires the use of an original rear main cap to finish an engine. These caps are cast from the highest quality Nodular iron and machined for ease of fitting to any 289 block. The I.D. of the main bearing bore is .020 undersize and the side registers are .010 oversize on each side for proper adjustment before line...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 27538 -
Used 3 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for seat belts and door ajar indicators. Blue and red light sockets. These are the same sockets for the seat belt reminder and door ajar warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 26309 -
Reproduction 3-Speed Transmission Instruction Tag for the 1967 - 1968 Mercury Cougar / Ford Mustang
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 32390 -
3/8 washer for installation of idler, adjusting pulleys, and brackets, on some 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, 1-2 are typically used per car.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 32389 -
3/8-16x7/8 Bolt for installation of idler, adjusting pulleys, and brackets, on most 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, up to 8-9 are typically used per car. 9/16" hex, washer head bolt.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 26258 -
Reproduction 390 / 428 4V AT / MT Emission Decal for the 1968 Mercury Cougar / Ford Mustang
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 15382 -
New One-Piece, Rubber Coated Fiber Oil Pan Gasket for the 390, 427 or 428 FE Big Block engine in the 1968, 1969 or 1970 Mercury Cougar and Ford Mustang. 3/32" thick.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41284 -
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 27537 -
Used 4 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for parking brake and low fuel indicators. Yellow and green light sockets. These are the same sockets for the parking brake and low fuel warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in you Cat? The video...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41283 -
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 10565 -
Concours correct Autolite spark plug wires for any 1969 Mercury Cougar or Ford Mustang with 428CJ engine with thermactor smog system. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Orange spark plug boots on this set.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 26385 -
Decal Text:
Autolite
EV-45
C8OZ-6A666-B Replaces Ford Part #: C8OZ-6A666-B.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 31620 -
Good used rubber ram air seal for any 1968-70 Mercury Cougar or 1968 Ford Mustang. May have some warpage issues.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 32578 -
5/32 Allen wrench. We offer this Allen wrench to go along with our dash bezel removal tools. This handy dandy 5/32 Allen wrench is needed to attach the ignition bezel tool to any of the 1967-69 Mercury Cougar or Ford Mustang ignition switch bezels.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 26277 -
Reproduction 60000 Mile 6 Month Lube Sticker for the 1967 - 1973 Mercury Cougar / Ford Mustang
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 32579 -
Hex screw for attaching the black plastic elbow to the right or left hand A/C dash duct. Correct replacement #8 washer head tapping screw. Sold individually, two needed per car. One on each side. Fits 1967-68 Mercury Cougar and Ford Mustang with factory air conditioning.
Wanted!
Buy
Details
Availability: Ships Direct from Supplier (Except International)
Item #: 30963 -
Reproduction driver side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.
Wanted!
Buy
Details
Availability: Ships Direct from Supplier (Except International)
Item #: 30962 -
Reproduction passenger side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 26529 -
Seals the hole where the A/C lines pass through the core support on the driver side on Mercury Cougars and Ford Mustangs. Replaces Ford part #: C7ZZ-19810.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 11-0469 -
Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. There are a couple of versions of this housing. There is a version with a cooling nipple for cooling the...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 11-0472 -
Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version. There are a couple of versions of this housing. There is a version with a...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 11-0385 -
Air conditioning fan blower assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.
Wanted!
Buy
Details
Availability: Out of Stock, On Order
Item #: 32348 -
Reproduction black center A/C vent for the 67 - 68 Mustang.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 20529 -
Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 20530 -
York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 13831 -
Redesigned modern evaporator has 35% MORE PASSES, using three-circuits, instead of the original single-circuit design. This is a direct bolt-in replacement and requires no modification.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal. It has been our experience that these often fail within a few years. We suggest flushing and pressure...
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 11-0405 -
Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade A vents will not have any cracks or breaks.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 11-0406 -
Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade B vents will mostly have a missing metal bracket and / or small crack or break usually around the mounting holes.
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 30613 -
Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Nice fit, made of plastic. Will work with or without console, has slightly wider wings for clearance of the rear of the factory installed consoles.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 11-0407 -
Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade A vents will not have any cracks or breaks.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 11-0408 -
Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade B vents will have a small crack or break usually around the mounting holes, but will not effect it's functionality.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 30614 -
Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs without a console.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41915 -
Concours correct A/C discharge hose for Mercury Cougars and Ford Mustangs.Replaces part # C7AZ-19972-A or C7ZZ-19972-A.This hose is compatible with both 134a and R12 refrigerants.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41940 -
Concours correct A/C sight glass hose with a 90° fitting for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41924 -
Concours correct and constructed in original Ford style black thermoplastic material with a nylon barrier. This hose assembly is built to be compliant for R-12 or 134a refrigerants.NOTE: We have three hoses from a previous supplier that we have available for about half the price. The only difference would be that instead of the thermoplastic material, these are the standard rubber type hoses. Pick one up here. ...