1969 Mercury Cougar

Used oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Bare Metal oil pan. Has no paint, chrome, or protective coating. Replaces Ford Part #: C5ZZ-6675

Includes drain plug

Nice reproduction oil pan, painted stock Ford blue on the exterior.

[No Description Provided]

Reproduction Small Block Chrome Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302

Includes drain plug.

This is by far the best, most correct FE pan ever offered. Very accurate reproduction of the C6OZ-6675-A oil pan used first on the 1966 Fairlane and Comet with one of the 390 CI optional engines. It is 100% correct for 1968 and early 1969 428CJ. It is not 100% correct for the 428SCJ but still a good alternative.

Reproduction Small Block Painted Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302

Used oil screen pick up tube assembly from a small block Ford 351W or Windsor engine. This is for most front sump 351W engines in Ford cars from 1969 to at least 1971. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. * Excludes 289/302 and 351C engines, and all F...

Used oil screen pick up tube assembly from a 1969-70 Ford Boss 302 engine. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes.  * Excludes regular 289/302 engines. Replaces Ford Part #: C9ZZ-6622-A

Hex shaped extension. Made from machined metal. Highly polished and Chrome plated. Replaces Ford Part # : C2OZ-9B339-C

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP

Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339

Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...

Reproduction oil pressure remote sending unit tube assembly mounting kit.. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge. The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation.

Bare outer tube for the 69 Cougar or Mustang tilt steering columns. This item will be free of major rust, and will have to be painted to match your car. Keep in mind that these tubes are year specific. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out our video on Tilt Column service and repair below. ...

Reproduction overflow hose with smooth outer wall. Hose length 36"

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. If you buy the insulation pad that lies beneath this panel...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. If you buy the insulation pad that lies beneath this panel...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

These fasteners were used to keep your package tray in place. In 1969 - 1970 the two clips were held in place with screws. Sold individually. We have seen various tech type screw with both large and small heads on them for fastening these clips. Same clip as was used in 1967-68, but without the push clip. We try to supply the screw, but you would likely want to get fresh ones, they are nothing special.Replaces Ford part number C4AB-6246698-A.

If losing weight in your 1969 - 1970 Coupe is what you are after then this would be a good part for you as it weighs less than one pound and the original weighs approximately five pounds. The original is made of the same material as the sound deadener found under the carpet and we rarely get good examples in stock.

Reproduction pair of package tray retainers for your 67 - 70 Cougar or Mustang. Made from stamped steel with a black finish to keep them from rusting. They install in the front of the package tray, keeping it secure.

Reproduction disc brake pedal pad for the Mercury Cougar or Ford mustang equipped with a manual transmission. This unit is a perfect fit! Replaces Ford part # C5ZZ-2454-D.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

This great fitting reproduction emergency / parking brake pedal pad for the Mercury Cougar or Ford Mustang. This is supposed to have a stainless steel retaining ring around the perimeter. We carry both reproduction and used. Replaces Ford part # C9ZZ-2454-A.

Reproduction foam rubber donuts that help cushion the brace from the tail panel on any 67 - 73 Cougar or Mustang.Replaces Ford part number C5ZZ-6540996Sold as a set of 4.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.This VHT roll bar and chassis paint will give the appearance of an expensive, baked on finish. Heat resistant to 250 degrees, this epoxy coating also resists chemicals, rust, corrosion and salt. No primer is needed. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ...

VHT epoxy paint is great for a number of applications. It's a unique one step protective coating that dries quickly and doesn't require a primer. It provides excellent rust, corrosion and chemical resistance which, needless to say, is ideal for anything you're doing under your hood or under and around the body of your car. One can covers about 12 - 14 square feet.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. SEM brand COLOR COAT paint is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not recommend this product for driver side arm rests, door pull straps, shift...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This is a GOOD match for 1967-68 Cougar parchement / off-white interiors. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

This charcoal black aerosol paint is a very close match to the original finish used on 1967-68 Cougar XR-7 lower dash structures and steering columns. We've tried it ourselves and have been satisfied with the results. Our only critique is that it's a bit slower to dry than other paints we're used to. The AccuMatch(TM) Interior Paints are the result of years of work and perfectly match the original color shades. Each color has been expertly color-matched. Paints feature extra-high pigment...

Professional grade paintless dent removal kit. This kit is designed to work with smaller blemishes such as dents from hail, door dings, etc. Complete with universal high strength glue sticks, puller, and a variety of different sized gluing tabs. NOTE: Remove glue with 91% alcoholAlthough we work with 67 - 73 Cougars and Mustangs, this kit is good for a wide variety of different vehicles.

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

Cork pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Rubber gasket also available.

Rubber pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Cork gasket also available.

Rubber pan gasket for the FMX transmission on any 1969-73 and 1969-73 Mercury Cougar and Ford Mustang.

Pan head screw for attaching the sport mirror glass assembly into the passenger side painted sport mirror head. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. 8-32 pan head screw with Phillips screw head. Do you have questions about installing a passenger side mirror or using Riv-Nuts? ...

Reproduction anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"

Used anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"