1969 Mercury Cougar

Reproduction rubber roller for the metal tilt cover plate on any 1968-69 Ford, Mercury, or Lincoln. Often times the rubber disintegrates over time. This is needed to keep the cover plate tight to the side of the steering column. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Used roof mounted switch that is rather delicate. As you can see from the pictures, the chrome coating has started to peel slightly. 

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed with the Autolite logo.   1967 Cougar/Mustang could have come factory installed with either red or gold. 1967 - 1969 factory serviced cars could have gotten the red or gold until stock was...

This is the type of material that was used to install gasketless windshields starting in 1969. Tom

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

Used rubber sleeve from the front outer bumper mounting tube bracket. Must be for anti squeak or for protection of the front turn signal wiring harnesses. One per side, sold individually. The Ford part number for this item is D0WB-17B947-A. These were made from rubber tubing with a wall thickness of 1/8 inch. Inside diameter is approximately 3/4 inch, and about 2-1/2 inches long for these 1969-70 bumper sleeves. Limited to available stock. These sleeves were installed on 1969...

New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily.*NOTE* This item can only be shipped via UPS ground. No Foreign orders please. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Unfortunately this is yet another incorrect reproduction made by someone who has never even sat in a Cougar. No embossment, no courtesy light holes if you have xr7 and no foil backing. These are sold as a pair. There are two different sources that will hand make these to show quality specs, you can locate them at www.mercurycougar.net   Sorry, we never get good used units in these days. *NOTE*  This would be a good time to purchase trunk filler boards and package tray if you need...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Reproduction rear interior sail panels for 1969 Mercury Cougar XR7 and standard models with courtesy light provision. Reproduction rear interior sail panels made from foam core backer board, covered in textured white vinyl with embossed border. Original panels were made of textured paper. Metal reinforcing ring installed for courtesy lights. Several different versions of courtesy lights were used 1969-70. These allow the installation of the chromed reproduction courtesy lights which look great...

Good grade A used jack with correct fine threads. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not. Grade A will not have rust or damage.

Good used jack with correct fine threads. Notice the remnants of the original jack instruction decal. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not.Grade B will have Rust and or the top portion letter "M" fitting may be damaged.

Automatic chokes had been the norm for many years so a notice to the operator was a must. Decal Text:NOTICEThis vehicle is equipped with a manual choke located immediately below the ignition switch. For proper starting use manual choke. ...

Sold as a Kit as Pictured.

Sold individually Zinc with Bi-wax sealer (dark silver with gold color on threads)

New hex head screw for attaching the fuel filler neck to the rear body. 67 to 70 Mercury Cougar and 1965-70 Ford Mustang. 1965-68 filler necks require 4 of this style screws. 1969-70 filler necks require a total of 5 hex head screws. #10 x 3/8". Replaces Ford number 42120-S8.

Original style fuel tank installation screw. 3/8 inch hex head. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks. See item 11942 for the kit of 12 screws, better value.

Original style fuel tank installation screw kit. 3/8 inch hex head. This is a set of 12 new screws. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks.

Sold individually. Two needed for globe box cable 1967-70 Mercury Cougar. 3 needed for installation of turn signal switches 1967-73 Mercury Cougar or Ford Mustang.Ford number 379203-S. Phosphate & Oil (gray-black)

Individual screw for attaching the headlight retaining ring on any 1967-70 Mercury Cougar or 1965-70 Ford Mustang, and pretty much most all other Fords during those years. #8 stainless steel screw. Two needed per headlight bulb retaining ring. A total of 8 would be needed for a quad headlight system on all Cougars.Replaces Ford part number 375452-S.

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually. Zinc (dark silver)

Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Sold individually.  24 required per car, set of 24 also available. ...

24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Also sold individually.

Special Phillips pan head screw for attaching the pancake motor to the quarter window regulator. 1969-73 Mercury Cougar and 1971-73 Ford Mustang. Weird threaded screw, called a triangle threaded screw. Slightly larger than 1/4-20. Unique and limited to quantity on hand. Three screws per regulator, sold individually. Ford part # 381530-S. *NOTE* For those of you who like to rebuild and refurbish your own parts, check out our video below. It will take you through the pancake motor...

Three required per car, includes washer. Used in conjunction with a steel clip to secure lower flange to column tube.

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used unique Phillips bright finish screw that attaches cable guides to roof.

Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Correct size, style, and color screw for all 1969-70 Mercury Cougar front turn signal bezels. Sold individually, 4 total needed per car.Replaces Ford part number 52445-S.

8-32 screw for attaching the window regulator drive arm slide

New screw for attaching horn pads onto steering wheels 1968-69. 2 or 3 required, sold individually.

One kit does both rear armrests for the XR7 or Standard interior coupe.

Fits Standard and XR7 Sold as a Set as Pictured.

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

Fits all Mustangs