1969 Mercury Cougar

Good used PCB that has no burns, corrosion or separating areas. The red PCB (printed circuit board) was used in the latter part of 1969 (from 2/17/69 on) and all of 1970. In 1969 if you had a white plug connected to the PCB it used a red PCB, if you had a black plug the blue PCB was used. Check out the video below on our new gauge tester: ...

Ford part number C9WY-10K843-D Finally! A made in the USA reproduction printed circuit board for your late built 1969 - 1970 Standard Cougar. This is a spot-on, class "A", no excuses reproduction that will give you decades of reliable service. This part exceeds the quality of the originals in that it is made from thicker materials, is bonded better, is more flexible and does not contain formaldehyde as did the originals. This is only for use on the late 1969 Standard white wiring harness...

Ford part number C9WY-10K843-D Finally! A made in the USA reproduction printed circuit board for your late built 1969 XR7 or Eliminator (built after 2/17/69) and all 1970 XR7 and 1970 Eliminator. This is a spot-on, class "A", no excuses reproduction that will give you decades of reliable service. This part exceeds the quality of the originals in that it is made from thicker materials, is bonded better, is more flexible and does not contain formaldehyde as did the originals. This is only for...

Very rare three part fold out printed on heavy stock promoting the Coca-Cola give away cars.

Nice reproduction of the prop rod used on the 1970 Eliminator. This will work on any 1967 - 1973 Cougar that has had a spoiler installed. The pictures of the installed original prop rod were taken at the 2008 PROWL Cougar show hosted by Cascade Cougar Club. The concours correct BOSS 302 Eliminator pictured is owned by John Benoit in Edgewood Washington. Click on images to enlarge. The above picture shows the approximate location of where to drill the hole in the passenger side rear quarter...

This after market adjustable proportioning valve is far superior to the original equipment. Fully adjustable for tuning front to rear brake bias. Requires some routing modifications of brake lines for proper fit. Includes adapter fittings. Replaces Ford part # C5ZZ-2B091-A, or C7OZ-2B091-B.Fits: 1967 Mercury Cougar 1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang 1968 Ford Mustang 1969 Ford Mustang 1970...

C9OA-2B091-A Cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. 1969 disc brake cars have it mounted almost directly on the Pressure Differential Valve on the driver side fender apron. The pressure differential valve is also commonly called the 'brake distribution block'. Please understand that most all of these valves will have some tool marks from pliers or vice grips. It is what we have left after previous owners have serviced them...

Reproduction proportioning valve for the Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. This valve is most often found at the junction of the high pressure hose back at the rear end, or later, found with the distribution block mounted on the driver side apron (inner fender). Replaces Ford part # C7OZ-2B091-B.Here’s a video to help you rebuild the distribution block and proportioning valve: ...

1969 and 1970 Mercury Cougar rubber sleeve. Attaches to the front bumper brace tubes. Attaching point is where the side marker wiring harness makes contact with the bumper brace. About 2-3/8 inches long for those wanting to replicate from a piece of thin wall 7/8" ID rubber tubing. Sold individually, two needed per car.

This plastic plate / bracket is installed between dimmer switch and the floor of your 67 - 73 Cougar to provide a bit or protection for the wiring.

Used cast dual sheave alternator pulley. Casting number C9AF-10A352-C, we believe that these originally had a zinc dichromate finish. Called out for use on various 1969-70 Mercury Cougar and Ford Mustang with a need for a dual sheave alternator pulley.*Note - this is a cast pulley instead of the common stamped steel single sheave version.Ford part # C5AZ-10344-L.

Reproduction alternator pulley, single sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

C9OZ-6A312-B. Application 1969 351W engines without air conditioning, and with or without power steering. Ford casting number C9OE-6312-E. Double sheave 69 crank pulley.

Ford part number C8AZ-6A312-C. Application 390-2V and 1968 - 1969 390-4V engines without air conditioning and with power steering. Ford casting number C8AE-6312-C. Double sheave 68 69 crank pulley.

NOTE* After comparing to the original pulley, we've found that this reproduction is approximately 3/16" shorter in overall height. New crank shaft pulley, single sheave small block Ford 289 / 302 351W engines up to 1969. Single V-belt or fan belt pulley, means for use with only the alternator. Not for use with power steering, air conditioning, or smog pump. Measures just under 6-1/4 inches in diameter. Single sheave crank shaft pulley with 3 bolt holes, excludes engines after 1970....

Used crank shaft pulley for any 1969 Mercury Cougar or Ford Mustang with 351w engine. This is a single groove pulley with a 6-1/8 inch diameter, and would have been used without power steering. One belt just for the water pump and alternator. Also fits other cars with 351 Windsor engines without P/S.Replaces Ford part number C9OE-6A312-D.

Ford part number C8OZ-6A312-C. Applications: 1. 1968 289 - 302 engines with Thermactor emissions and manual transmissions, may have power steering or air conditioning. 2. 1969 Boss 302 Eliminators with all applications. Ford casting number C8OE-6312-C. Triple Sheave 68 crank pulley.

C9ZZ-6A312-B. Application 1969 351W engines with air conditioning. Power steering optional. Ford casting number C9ZE-6312-B. Triple sheave 69 crank pulley.

C9OZ-6A312-E. Application 1969 390 engines with air conditioning, power steering optional. Ford casting number C9OE-6312-C. Triple sheave 69 390IP 390-4V crank pulley.

For 1968 390-2V engines without air conditioning, with dual alternator belts, and with power steering. 1968-69 390-4V, 427 GT-E, or 1968-69-70 428 Cobra Jet engines. All without air conditioning. All with dual alternator belts, and with power steering. Triple sheave 1968-69-70 crank pulley.Ford part # C8AZ-6A312-D, Ford casting # C8AE-6312-D.

C9OZ-6A312-F. Application 1969 and 1970 428CJ all with air conditioning, power steering optional. Ford casting number C9OE-6312-D. Triple sheave 69 70 428 CJ crank pulley.

Application 1967 - 1968 - 1969 Cougar with either 289 / 302 / 351w engines with air conditioning. After 9-11-66. Casting number 7AD. 5" diameter and a 3/8" sheave width.

Application, 1968 289/302 engines without air conditioning, but with a single alternator belt. 1969 351w engine without air conditioning, but with dual alternator belts. Casting number 7AE. 4-5/8" diameter and 5/16" sheave width.

Application could be for any 1967-69 Ford 289 / 302 /351W, but with only a single alternator belt. This is a copy of the Ford 7AA power steering pulley. This pulley mounted correctly on an OEM pump with factory brackets, will run on the second V-belt from the inside. The inner most fan belt runs the alternator. You would be using a single belt on the alternator. Correct application is for 1969 with 351W engines. 5-1/4" diameter and 3/8" sheave width.

Application, 351w engine without air conditioning, but with only a single alternator belt. Casting number 7AA. 5-3/16" diameter and 3/8" sheave width.

Application, 1967 - 1968 - 1969 - 1970 390 / 428CJ engines with air conditioning. Casting number AF. 5-3/4" diameter and 5/16" sheave width.

Application 1968 - 289-2V, 302-2V, 302-4V, all with manual transmissions and without air conditioning. Also 1968 390-4V and 1968 - 1970 428CJ, all without air conditioning. Pulley diameter 4.75" inches. Ford part number is C8AZ-9B447-B and the engineering number as seen on the front of the pulley is C8AE-9C480-A.

C7AZ-8509-E 289/302 Water Pump Pulley-Used C7AZ-8509-E Thermactor emission systems. Application also includes 1969 Boss 302 Eliminator. All applications are without air conditioning. With or without power steering. Triple sheave pulley all equal diameter at 6-7/16 inches. Ford casting number C7OE-8509-B. *1967 application with standard cooling (17 inch radiator) *After 11-13-1966

C8OZ-8509-A Applications include 1968 289 / 302 with automatic transmissions and 1969 351, all-without power steering, air conditioning and with standard alternator with a single sheave pulley. This pulley is 6-1/2 inches in diameter and is a single sheave pulley. Ford casting number C8AE-8A528-F.

For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. 2 sheaves with a diameter of 5-7/8 inches. This is a good copy of the original water pump pulley, it has no stamped part number.Replaces   C6AZ-8509-A or C6AE-8509-A.

C6AZ-8509-A For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. Thermactor OK on any application. 2 sheaves with a diameter of 5-7/8 inches. Ford casting number C6AE-8509-A. *For year 1967 only > Notes say Prior to 1/9/1967.

Fits all 1969 390-4V engines without power accessories. No power steering, no air conditioning, and with a single belt alternator. Single sheave pulley, 6 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.Replaces Ford number C9OE-8509-D. Before 2-17-1969.

C8AZ-8509-A All 390 engines without power accessories. No power steering, no air conditioning, and with a single belt alternator. Single sheave pulley, 7-1/4 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-1/8 inches.Ford casting number C8AE-8A528-B. After 2-17-1969.

C8AZ-8509-D 1969 428 Super Cobra Jet only (V and W code axles), 1970 428CJ and 428SCJ prior to Sept 1, 1969. No air conditioning, power steering permissible. Three sheave pulley, 6-1/8 inches and 7-1/8 inches in diameter pulleys. Ford casting number C8AE-8509-C was originally imprinted in ink, if you look closely between the two bonded together pulleys that make this pulley up you may be able to read the C8AE-8509-A stamped casting number from the two sheave inner pulley.

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

Used power convertible top pump, motor and reservoir for the Mercury Cougar or Ford Mustang convertible. We do offer an excellent reproduction which you can get right here, but nothing beats original FoMoCo. There is a difference in the space of the mounting bracket between the 1969-70, and 1971-73 Cougar or Mustang convertible top pump assemblies. Not to be interchanged.Our pumps are tested, we recommend flushing the pumps and reservoirs prior to installation. Save your grounding wire,...

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with any V-8 engine. This unit is also for the 1970 Cougar or Mustang equipped with the 428CJ. These are bare pumps, stripped of pulleys, canisters, dip sticks, tags, and brackets. Suitable for core rebuilding. Typically these pumps would have been tagged with numbers which include: HBA-BF, HBA-BF1, HBA-BK, and HBA-BR. *Note - Excludes all 1970 cars with 351 or 302 engines. *NOTE* Core exchange not required. ...

This is a new old stock windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). Replaces Ford Part #: C9AZ-17664-A.

This is a reproduction of a later service replacement version of the windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models).The original Ford part was part number C9AZ-17664-C

Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.

New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.

Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.

Our 1969 grade "A" rear quarter panel extensions have no obvious dings, scrapes, or warping due to over tightening of studs. However, avoiding the bumper contact dents is impossible. These will have small dents from bumper contact. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-6528519, Mercury MPC # C9WY-6528011-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our 1969 grade "A" rear quarter panel extensions have no obvious dings, scrapes, or warping due to over tightening of studs. However, avoiding the bumper contact dents is impossible. These will have small dents from bumper contact. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-6528518, Mercury MPC # C9WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs minor repairs to be show quality. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-6528519-A, Mercury MPC # C9WY-6528011-A. Do you have questions about your Cat's factory...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs minor repairs to be show quality. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-6528518-A, Mercury MPC # C9WY-6528010-A. Do you have questions about your Cat's factory...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" driver (left hand) side rear quarter panel. We ask that you call to discuss condition, price, and cut...