1969 Mercury Cougar

Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...

This two piece heat shield has a very narrow application in that it is a one year only item and only for the 390 IP (Improved Performance). It does not mate to metal a "S" shaped heat riser tube but rather a flexible paper-foil tube that attaches to a reducer on the bottom side of the snorkel. Very hard to find item, harder yet to find one that has not rusted out. The unit shown is "tender" in a couple of spots. The lower section carries a Ford part number of C9OZ-9A603-D and the upper section...

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

Ford part number C9ZZ-9A603-C for the upper section and C9ZZ-9A603-D for the lower for this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this lower section also. metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this upper section also.

These are getting so hard to find without a broken drain cock or rust in the metal lips. The unit pictured here is typical of what you can expect when you buy out used complete box. Plan on repairing the drain cock or other minor cracks. All doors will be functional, we will not promise the evaporator is good and we do promise the heater core will be bad. We have a few single halves if you need the half without the drain cock. Two versions for 1969-70 Mercury Cougar and Ford Mustang....

These are getting so hard to find without a broken drain cock or rust in the metal lips. We have a few single halves if you need the half without the drain cock. Soon we will have every single internal and external part from this assembly listed here, in the mean time give us a ring for those obscure parts! Two versions for 1969-70 Mercury Cougar and Ford Mustang. Difference is the evaporator and the orientation of the tubes. Look for the triangle shaped rubber line seal for the later 1969-70...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Due to the age, there may be a minor stress crack or blemish, it will be a good used assembly. Note that this does not come with a fan assembly, so you will need to reuse your old one.Heater core IS NOT INCLUDED. This icon means that we're looking to buy this part!WCCC is a...

C9ZZ-18A651-B Complete heater and power ventilation system control assembly includes bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. The power ventilation system was a pretty rare option for 1969-70. It included a center dash register as found on air conditioned cars and directed cool air through the center of the dash. Dearborn cars would have a code "VS" on their body buck tags, and Metuchen...

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

Nice used pocket brochure from November 1968, featuring various 1968-69 Ford, Mercury, and Lincoln cars such as 1969 Mercury Cougar, Thunderbird, Shelby Gt 350 and XR7-G. Picture shows Ford full size XL, 1969 Mustang Coupe, 1969 Mercury Cougar, Thunderbird 4 door, Lincoln Continental.This particular edition came from the "Greater Miami" area.

NOS or new old stock - C7SZ-13A165-A Bolt like pin that one or both sides of the hidden headlight hinge rides on. 1967-68 Mercury Cougar uses 4, 1969-70 Mercury Cougar uses 2 on the outsides. Also used on many other 1967-71 Ford, Mercury, and Lincoln cars with the vacuum operated hidden headlights. 1967 - 1970 Mercury Cougar and XR7 1967 - 1969 Ford Thunderbird or T-Bird 1968 - 1969 Ford and Mercury full sized cars 1971 Ford and Mercury full sized cars 1970 and newer Lincoln Continental...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade "A" hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

THE QUALITY ON THESE HOOD SCOOPS HAS DECLINED GREATLY, AS OF NOW WE WILL MOST LIKELY NOT BE ORDEREING ANY MORE UNTIL THE ISSUES ARE CORRECTED. Reproduction Eliminator hood scoop for the Mercury or Ford. Correct stud configuration, size and weight and far superior to our old scoop we offered. This scoop was made by using an original Eliminator scoop to make the mold. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. This...

BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. The Scoop measures 21 5/8" at the widest point on the front, 25" at the widest point at the rear and 26 1/8" tall when stood on end and measured at its longest point. The scoop is 2 7/8" tall at the front middle when mounted on the hood.Ford part # C9WY-16C630-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

This original Ford service replacement hood scoop is the same as a factory installed scoop except that it does not have the embossements for the hood grille used on the very first Ram Air Cougars (prior to September 1968) and it has extra mounting stud receptacles for use on multiple applications such as the Comet GT and the Mercury Cyclone. This version does have the reinforcing or webbing like the originals. Ford part # C9WB-16C664-C, C9GB-16C664-C, and D14B-16C664-AA. Found on the bottom. ...

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Reproduction gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

C9OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1969-70 351 Windsor 2V and 1969 351Windsor 4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. This hose is a bit longer than the 289/302 version due to the taller deck height of the 351 Windsor engines. *Note - These molded and contoured hoses were designed to work with the...

C7TZ-6A664-A Used after 02-21-1969. Original used hose that connects the original PCV valve to the carburetor spacer plate. All later 1969 S code 390-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *NOTE* These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake...

Used vacuum hose with inline muffler, connects the Servo Valve to the Regulator on 1969 Mercury Cougar and Ford Mustang with factory Speed Control. Hose about 42.7509 inches long. Ford number for hoses is C9ZZ-9D860-A.

Good used original power steering lower hose bracket and retainer with a new reproduction insulator installed in place of the original crusty or missing insulator.This bracket is for cars with the big block routed power steering hoses.

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

This is the 1967- 1968 retrofit or re-route hose kit! The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS for 1969. You will not find these at your local auto parts store or the the "Mustang Discount" folks. These hoses will also work on a 1967 or 1968 5/16" control valve fitting if it is routed the same as the big block. You will need to purchase the power steering hose bracket for the big block in order to make it work. This is a...

1967 - 1970 390, 427 and 428 & 1969 - 1970 302 and 351:  This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Includes both Pressure and Return hose that connect to the control valve. * 1967 - 1968 289 and 302:  This big block routing is far superior to the...

[No Description Provided]

We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang without Power Steering Cooler.  

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

Used spinner hubcap / wheel cover for the Mercury Cougar. This was and optional inset spinner that bolted onto your existing hubcap. 1968 was the first year the dealer option was available. Ford part # C7MA-1130-F

Brand new cap, sometimes the boxes are missing due to age.Ford part # C9WY-1130-C.Fits:1969 Mercury Cougar Standard1970 Mercury Cougar Standard

Used grade "A" XR7 hubcap / full wheel cover for the XR7 Mercury Cougar. The 1969 version of this hubcap / wheel cover used a white stripe around the center where the 1970 used black. Our grade "A" cap will have a minimal amount of scratches. Ford part # C9WY-1130-A.

New Old Stock XR7 hubcap / wheel cover for the Mercury Cougar. There were two versions of this cap, one with a white painted ring around the center, and one with black around the center. The white version was used in 1969, with the black version being used in 1970. Ford part # D0WA-1130-A

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a pink...

Quality reproduction. Fits all 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Lin, Hey, just wanted to thank you for your prompt service. Last Friday 4/24/09 I ordered a 71 - 73 Idler Arm and today (Monday 4/27/2009) I received it. WOW!!! I just wanted to let you know that you guys are...

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory power steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a yellow paint mark on...

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

New old stock bracket and pulley assembly for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539. Ford part # C8AZ-8678-C. ...

Used fixed idler bracket and pulley assembly with new installed bearing for 1968-69 Cougars and Mustangs with the 390 or 428CJ engine. This part will have a small bearing on the pulley and is not marked with a casting number. The 1970 bracket and pulley assembly was a service replacement part and are the same as the 68-69 with the exception of a slightly larger bearing. This later service replacement part is an economically priced service replacement for the earlier originals. All pulleys come...

NOS ignition switch kit for any 1968-69 Mercury Cougar or Ford Mustang. Includes ignition cylinder and plug with pigtail wires. This is a new old stock Motorcraft part. Comes as shown, you will need to reuse your key lock cylinder. Ford part number D1AZ-11572-C.

Used under dash wiring harness repair plug and pigtail to the ignition switch for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use after nearly 40 years.