1969 Mercury Cougar

Flawless chrome plating, available in stock depth only. Includes drain plug.

Reproduction transmission selector tube seal for the 69 - 70 Cougar or Mustang steering columns.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

New manufactured transmission yoke for a T-5 5 speed transmission.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX  cars.  *Excludes 351C-4v and 351CJ engines.

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Used transmission tunnel specialty cut. From a 1969 Mercury Cougar, slightly different than the 1970 tunnel.File picture of 1967 tunnel, you get a 1969 tunnel cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the...

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact.

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact. NOTE - When sending in your core, light pitting on the upper edge is acceptable. Heavily pitted trim will not be accepted.

Reproduction emergency / parking brake pedal pad trim piece for the Mercury Cougar or Ford Mustang. This great little reproduction looks good and is one of the little detail pieces that can separate a nice car from a mint car.Replaces Ford part # C9ZZ-2A487-C.

Used emergency / parking brake pedal pad that features all stainless steel construction. This unit cleans up very well with fine steel wool, has reusable folding tabs, and is easy to install. A great piece to finish off your interior!Replaces Ford part # C9ZZ-2A487-C.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Driver side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1969-70 Mercury Cougar coupe or convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number C9WY-6545119-A.

Passenger side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1969-70 Mercury Cougar coupe and convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number C9WY-6545118-A.

*NOTE* 1969 - 1970 Convertible mats do not have any covering to the right of the gas tank. This is in fact how the originals were made. Many Convertible owners prefer to have a full cover mat. If that is you we suggest you purchase the coupe mat for your convertible.This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern. Do NOT confuse this with the light duty mat you will see...

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern. The opening for the spare tire is not cut out, just in case that your Cougar has the space saver spare tire. You will need to carefully transfer the hole and cut it out yourself with a blade.Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see...

This reproduction is pathetic... It is made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. The correct dark gray speckled pattern for 71 - 73 is not available with this mat. No returns on this product, we suggest no mat is a better alternative than this poor...

Replacement steel tube for all FE intake manifolds. Tube connects to water pump via a rubber hose. Fits all FE - 352, 390, 410, 427, 428 engines. Best to replace when intake manifold is removed to drive out the old rotted steel tube. We use a little silicone on the smooth surface prior to installation. The connecting hose (and clamps) to water pump normally got painted Ford engine blue from the factory.

Used inner steering column tube for the tilt / tilt away for the Mercury Cougar or Ford Mustang. This unit fits within the outer steering column and is specific to 1969. Ford part # C9AZ-7212-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction oil pressure remote sending unit tube assembly. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge.The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell shaped oil...

Reproduction machined tube seat set, for all 1968-70 Mercury Cougar and Ford Mustang. Also some 1967 Cougar or Mustang control valve and ram cylindernwith the 5/16" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that early 1967 control valves had 1/4" fittings.

Good used 100% complete turn signal light assembly for your 1969 Cougar. Was also used on 1969 - 1970 Shelby Mustangs, GT-350 and GT-500. All clear lenses. Ford part # C9WY-13200-A for the passenger side assembly, C9WY-13201-A for the driver side assembly. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There...

Good used 100% complete turn signal light assembly for your 1969 Cougar. Was also used on 1969 - 1970 Shelby Mustangs, GT-350 and GT-500. All clear lenses. Ford part # C9WY-13200-A for the passenger side assembly, C9WY-13201-A for the driver side assembly. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There...

When your lights are sequencing too rapidly, causing the outer light to not fully illuminate, your original unit is most likely the culprit. This solid state unit replaces the small red (69-70) or green (71-73) flasher found under the dash, next to the radio. NOTE* Some vehicles have the wiring reversed, you can get though this problem by using spades and hooking up to the contacts of the flasher backwards.  This is the updated flasher unit for use with the updated sequential unit and...

When your lights are sequencing too rapidly, causing the outer light to not fully illuminate, your original unit is most likely the culprit. This solid state unit replaces the small red (69-70) or green (71-73) flasher found under the dash, next to the radio. Replaces Ford part # D0WY-13350-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Grade B speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G

NOS Speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln.  The 1968 Electrical manual shows a Lincoln part number of C7VA-9D752-G. Service replacement part number is D1VY-13305A. Would need to remove the white tilt bale collar prior to use.

Reproduction Speed or cruise control switch, for factory installed cruise control. Very rare option on a 67-69 Cougar or Mustang, also fits Thunderbird, Lincoln, Marquis. Keep in mind that these new levers will not come with the plastic plug at the end of the harness, you will need to use your old one, or you can splice as shown in the included installation sheet. As you know, these levers were made from plastic in the sixties and seventies. This new reproduction is machined from billet...

New Old Stock turn signal switch for any 1969 Mercury Cougar or Ford Mustang with fixed steering columns. This switch will also fit fixed column Ford's 1968-1969 Ford Crown Victoria / Full Size / LTD / Fairlane / Torino / Falcon / Galaxie & 1970 Mercury Comet / Ford Falcon / Early 1970 Ford Maverick / Mercury Comet without locking steering wheel & all 1968-1969 Mercury Comet's Ford part # C9AZ-13341-B.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

Replacement U-nut or clip for any 1967-70 Mercury Cougar trunk lid. These slide into the bottom of the trunk lid for attaching the hinges. Correct 5/16-18 threads, 7/8" from center of hole to edge. 4 total per trunk lid, sold individually.

9" inside the arch to the end of the threads. Thread size 7/16-20, includes tall nuts as shown. Concours Grade 5 flange nuts available separately, see related items.

Leaf Spring U Bolt for the 1967 - 1973 Mercury Cougars with isolators. Will work on any 67-73 Cougar. Does not feature flattened area at top like original. Includes 1 'U' bolt and 2 nuts. 4 total U-bolts needed per car.  *Note - For use with Cougar shock plate, angled wedge, rubber isolators and retainer boxes. Inside Height:   6-3/4"Inside width:   2 7/8"  (Same as axle tubes) Replaces Ford Part #: C7WY-5705-A. ...

This would be for the non-competition suspension Cougars. U-Bolt length 6-3/4 inches, and threads 1-1/4 inch in length. U-Bolts include two (2) correct style attaching nuts. Competition suspension U-Bolts run about 7 inches in length. Ford part number C7WY-5705-A for Competition Handling option.

One size fits all universal joint u-bolt kit. Complete kit required to attach universal joint to rear differential. This kit only works with the 1-7/8 inch U-joint caps. Many of the higher performance engines used 2 inch caps and the larger yokes.  Replaces Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

These coarse thread nuts have an integrated lock washer with serations for the Mercury Cougar or Ford Mustang. They will ONLY work with the U-Bolts used in conjunction with the lowering kits. The thread size is 7/16"-14. *NOTE* Eight of these are required per car and are sold individually.

Permatex Ultra Copper Sensor Safe High temperature silicone, good for any makes and years. This stuff won't harm your Oxygen Sensors, and is good for up to 700 degrees intermittent. 

Used grade "A" under dash wiring harness with a white plug end for the standard Mercury Cougar. Mercury used either a black or white plug end in the 1969 model year run. If you have a red printed circuit board, this harness is the one you need. All electrical harnesses are inspected, repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy...

Used grade "B" under dash wiring harness with a white plug end for the standard Mercury Cougar. Mercury used either a black or white plug end for the under dash harness during the 1969 model year run. If you have a red printed circuit board, then this is the unit you need. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will receive an in store...

Used grade "A" under dash wiring harness with a black plug end for the standard 1969 Mercury Cougar with air condioning. Mercury used either a black or white plug end during the 1969 model year run. If you have a blue printed circuit board, this is the unit you need. All electrical harnesses are inspected, repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also...

Used grade "B" under dash wiring harness with a black plug end for the standard Mercury Cougar with air coniditoning. Mercury used either a black or white plug end for the under dash harness during the 1969 model year run. If you have a blue printed circuit board, then this is the unit you need. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will...

Grade A used under dash wiring harness for Standard Model 1969 Cougars without air conditioning. Used grade "A" under dash wiring harness for the standard Mercury Cougar. Mercury used either a black or white plug end during the 1969 model year run. If you have a blue printed circuit board, this is the unit you need. All electrical harnesses are inspected, repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will...

Used grade A used under dash wiring harness for Standard Late Model 1969 Cougars without air conditioning. Mercury used either a black or white plug end during the 1969 model year run. If you have a red printed circuit board, this is the unit you need. All electrical harnesses are inspected, repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind...