General (Old Category Structure)

Reproduction cover board for the rear package tray found on the 1968 Mercury Cougar behind the rear seat, visible through the rear window. The 1968 tray is not as deep as the 67 as it installs under the tops of the rear side panels. In 1967 they installed over the rear vinyl covered panels. The difference between the WCCC panels and the others on the market is that we run them through a drum sander so as to give the textured side a more muted look and feel than unsanded masonite board. The...

Good used piece of insulation / sound deadener that is distinctly different from 1967. This pad weighs more than four times what the reproduction does and will much more effectively insulate the passenger compartment of your Cougar from sound, heat and cold. Notice it comes with the factory perforations for speakers and rear window defog unit.

Nothing matches the fit and feel of NOS. This will outlast the reproduction armrest three to one.

Base standard saddle arm rest on a 1967 Mercury Cougar or Ford Mustang, interior trim code 2F. Nothing matches the fit and feel of NOS. This will outlast the reproduction armrest three to one. Ford part number C7ZZ-6524140-A1F.

Reproduction disc brake pedal pad for the 1967 Mercury Cougar or 1965-67 Ford Mustang equipped with the automatic transmission. This is identical to the 1968-73 pad, just slightly narrower. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part # C5ZZ-2454-C.

C5ZA-2454-G or C5ZZ-2454-D New Old Stock manual transmission disc brake pedal pad with stainless steel insert as shown. Application is 1967-70 Mercury Cougar and 1965-70 Ford Mustang, 3 or 4 speed manual transmissions.

This is identical to the 67 pad just slightly wider. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part number D3ZZ-2454-A

C9ZZ-7A624-A

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

Replacement rubber material pan gasket for all 1965-73 C4 Ford transmissions. 

This used driver (left hand) side lower front fender patch panel is rust free with no prior damage. Cut with a plasma cutter, removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 70 has the bigger, recessed side marker lights and the 69 has the smaller style. ...

This used passenger (right hand) side front lower fender patch panel is rust free with no prior damage. Cut with a plasma cutter and removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 70 has the bigger, recessed side marker light and the 69 has the smaller marker. ...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and a 5/8" flange that butts up against the inner rocker. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and the ninety degree flange that butts up to the inner rocker is 5/8" tall. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

Reproduction patch panel for the front of the driver side (left hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the rear of the driver side (left hand) quarter panel on the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the front of the passenger side (right hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for rear of the quarter panel on the passenger side (right hand) of the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the wheel lip on the driver side (left hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward. Thus you will want this panel for the passengers side of those series. ...

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward, Thus you will want this panel for the drivers side of those series. 

Here is our used lower rear window channel which we will cut to suit your needs. Quite often vinyl tops will cause rust in this area and this part is cut from a rust free Western parts car. If you need the package tray attached there is no extra charge, but shipping costs will increase. We usually cut generous into the quarters and several inches up the sides of the rear glass. If you only need one side contact us as we can help.   ...

Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.

New old stock brass intake manifold fitting that screws into the rear of the 428 CJ intake manifold on all 1969 428 Cobra Jet engines. Similar to the 1967-68 version, but this one has an additional smaller nipple coming out of it.  Ford part number C8OZ-9A474-A.

C7AE-6A666-B is stamped on this used PCV valve. Absolutely correct for 1968 390GT, 427-4V GT-E, and 428CJ Mercury and Ford cars. Must be used with either of the 90° elbows available, reproduction or OEM Ford.. This is used, no guarantee that it functions like new. Ford MPC number C7OZ-6A666-A. There is a published procedure for refurbishing these valves. These positive crankcase ventilation valve can be disassembled. ...

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

New air cleaner breather element for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, includes cartridge holder, retainer clip and filter.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

These convertible black interior "A" pillar mouldings are sold as a pair only. The texture and contour look good when installed but when turned over you will see they are thicker than original and are made from a different material than original. These may require some grinding of high spots on the back side to make them fit flush against the windshield post. Replaces Ford part # C9ZZ-7603598-B and C9ZZ-7603599-B.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used condition pin and bushings for the 69 - 70 Convertible Cougar or Mustang.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

C3AZ-4730-B Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1970 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper. The casting number seen on the 67-68 is C3AA-4906-C, this version has fine threads. The version most often seen on the 69-70 is C9OA-4906-A. It will have a coarse threaded mounting stud. Two of these were used on certain 1967 Shelby Mustangs with traction bars.

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.

C7ZA-3590-A Early 1967 Steering box pitman arm with 1 inch sector shaft. Manual steering only, used with SMB-C and SMB-E steering boxes. Ford part number C7ZZ-3590-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below.

D1ZA-3B153-AA 1971 - 1973 Manual steering pitman arm. May also have casting number D3ZA-3B153-AB. Ford part number D1ZZ-3590-A.

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used door hinge anchor plate for attaching the door hinge to the body pillar. All positions are the same, upper, lower, driver and passenger sides. Fits all 1969-70 Mercury Cougar and Ford Mustang.Ford part number C9ZZ-6502666-A.

Item is the lower half only of the air conditioning plenum from a 1969 Mercury Cougar or Ford Mustang. This would be the version found at the beginning and most of 1969. Unique in the way the evaporator lines are configured. The later version and all of 1970 has the box with the triangle shaped cut out for the evaporator lines. The lower section is the portion that has the drain tube that is often broken, you may find a repair done to the ones that we sell. These lower sections may have some...

One required per car, mates to female version attached to the under dash loom. Same plug for tilt and non tilting columns.

This used plug end will work on your 69 - 70 Standard or XR7 as well as the 69 - 70 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.*Does not include wires

This rubber plug is found on the bottom side of 68 and 69 Cougars without tilt column. It covers the access hole for the bolt that removes the column head / collar. We notice that most cars do not have them in place. This could be due to over site at the factory or them being lost over the years as the car has been serviced. We have also noted that Dearborn cars rarely if ever have them present and San Jose built cars often have them in place. If you have a Dearborn built car and have this...

Used taillight wiring harness repair plug and pigtail to the passenger side (right hand) center taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

This poster is a meticulous recreation of the 1968 original that Lincoln-Mercury dealerships had on display in their showrooms to advertise the Cougar XR7-G. We were able to have an original poster professionally scanned, the images were restored, and the text carefully recreated to match the original. The result is a fresh new version of a rare, iconic display piece.This 24" x 36" poster is smaller than the original, which was a massive 36" x 48". This makes it easier to display, and easier...

In 1967, one could order from the factory a power drum brake Mustang or Cougar. In 1968 - 1973 that option was discontinued and all you could order was manual drum all the way around or power disc in front with drum in the back. This kit is for the person who already has the power booster and pedal in place and wants to convert to power disc in the front. Since the 1967 model year used the same spindles for disc or drum brake cars you can do this conversion and never even have to take your car...