General (Old Category Structure)

This is a complete set of four used headlight bulbs, marked with the FoMoCo logo. These sets come with two high beam and two low beam bulbs. Each bulb is tested by the electrical department. If you're trying to keep your Cougar or Mustang as close to original as possible, you should definitely grab a set.These bulbs are date coded, so if you want a particular date, be sure to mention it in the comments section of your order.  

This complete four piece kit is for any small block 289, 302, or 351 Windsor Cougar 1967, 1968 and 1969. 

This complete four part kit is correct for any 1967-68 small block 289 or 302, and 351 Windsor Mercury Cougar or Ford anything 1967, 1968 and 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut.If you do not have a air conditioning you will need a spacer in place of the round spacer shown. If you have the 351 Windsor without A/C, you will need a the rectangular spacer which is sold separately.

This complete four part kit is correct for any 1969 small block 351 Windsor Mercury Cougar or Ford anything 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut. If you do not have a air conditioning you will need a the rectangular spacer which is sold separately.

We ask that you call us on this one. Roof cut includes the roof skin, 'A' pillars cut about 4 inches from the top, rear or 'C' pillars cut below the leaded seam. We have plenty of inexpensive, damage free roofs that have never had a vinyl top installed. If you want the pillars intact this triples the size of the crate and makes it cost prohibitive in most cases. Longer cuts with long extended pillars add greatly to the cost of shipping. This is a perfect cut for a Cougar owner looking to...

15 Piece kit that includes quarter panel drain plugs.

This is a complete shaft. Lower, upper and knuckle. This shaft may have plastic pins broken due to age and handling. It is functional. May have light rust and knuckle will have been tightened if needed.

This listing is for a set of four inner and outer wheel houses. Not only will buying a set of four save you money on the purchase price but it will save you on shipping as we remove them from their individual boxes and nest them together in one box.Attention international customers:This set is too large for us to ship directly in a single box using any of the international shipping methods we offer.  If you would like to buy this kit, you can either: Use a shipping broker to...

Concours Correct Spring attaches snorkle thermo door to Snorkle Base Replaces Ford Part # C8AZ-9A652-B

NOS Motorcraft condenser for point type distributors on any 1969-73 Mercury Cougar or Ford Mustang with V8 engines. Ford part number C9AF-12300-B and C9AZ-12300-A.

This unit is for Mercury Cougars and Ford Mustangs, is pre-assembled, and includes the drier and all brackets.

Our new high performance condenser kit comes pre-assembled with the drier and all brackets. 1967 - 1968 condenser shown. These condensers are one of the highest performing, durable condensers available in today's automotive market. This condenser was designed specifically to increase heat transfer for lower head pressures during idle situations, allowing more airflow to pass through the condenser and give the radiator enough airflow to operate properly. Remember to remove your coupler...

Original used 390 or 428 Cobra Jet piston connecting rod. These are marked C7AE-B. Rods and caps only. We strongly suggest using ARP aftermarket rod bolts. Limited quantity available, call to inquire. Replaces Ford part number C7AE-B and C6AZ-6200-C. *Note - Excludes 428 Super Cobra Jet engines.

Reproduction Console Ashtray Bumper for the 1967 Mercury Cougar or Ford Mustang.

The picture above shows these bumpers installed in the 100% correct reproduction console that we sell. These are sold individually, 2 required per car. Replaces Ford part # 379919.

This ashtray features correct plating, but customer reviews indicate that they are not a perfect fit and slightly different from the original, see reference photos above.  Replaces Ford part # D1ZZ-6504788-A.

Used ashtray for the 71 - 73 Cougar or Mustang. Customer reviews indicate that are differences between the original the reproduction, see reference photos above.  Replaces Ford part # D1ZZ-6504788-A.

Nice reproduction clear rectangular clock lens for consoles. Fits all 1971-73 Cougar and Mustang consoles. The only downside is that these lenses have a slight manufacturing flaw - there is a small crack in the hole for the clock knob (see pictures above.) Although you won't notice it unless you look closely, we prefer to be up-front about the products we sell. With that in mind, this is currently the only available reproduction lens for this application, and we think that it looks a lot...

Good used console clock surround bezel with no cracks, or peeling chrome. Engineering number on the backside reads D1ZB-15017-AA

Differs from the original lens in that it is all white. The original was painted white on one half and left clear on the other.

Fits 1967 and 1968 Standard or XR7

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

Reproduction aluminum shift indicator console overlay for the Mercury Cougar or Ford Mustang. Although a brushed finish is correct, this reproduction has a coarser brush stroke when compared to the originals and is a bit dull.  We recommend a quick polish to make them look closer to the finish of the originals. These fit well, and unless you put them up against an original, it is hard to tell the finish is slightly different. This installs around your console...

Made to concours standards. Replaces Ford Part # D1ZZ-6506024-A

Mini console assembly, comes with ashtray receptacle, wiring and socket, and console with a casting number of D1ZB-65045B72-A. Used for automatic or manual transmissions. These came color keyed to your interior, add your desired color in the comments section of your online order. We will try to accommodate color requests where possible. We will select and ship what is available, these are easy to detail with the various vinyl paints available. These are used, and often the ashtrays will need...

Exact reproduction horn ring contact components for the standard horn ring used on two spoke steering wheels, replaces Ford part # C9AZ-13A805-B. Includes new hardware

Horn ring contact components for the standard horn ring found on 68-69 2 spoke steering wheels. Ford part number C9AZ-13A805-B. Not as shiny as the reproduction kit but the price is less and the quality is FoMoCo original all the way!

Four required per car, used only on the driver side master power window switch, must have carbon fiber insulator in between the two plates.

A needed part for giving your car a tune-up.

New midland control hub assembly and disassembly tool for use with the 67 - 69 Cougar and Mustang Midland style booster

Used wiring pigtail with light socket for illuminating the heater and air conditioning controls on Mercury Cougars and Ford Mustangs. Tested and is ready to install. Includes the clip for securing wire to the control housing. Bulb 1445 sold separately.Ford part number C5AB-18541-A

Premium quality original FORD valve that has been re-manufactured to original tolerances. Quality part that is rebuilt by a true craftsman here in the USA. *NOTE: Our rebuilt and reproduction control valves all come pre-lubed with the correct amount of grease. If out of the box you add more grease, you will damage the valve. Unlike some suspension parts these are not designed to add grease until you see the grease coming out of the seal. Our warranty does not cover over lubricating. ...

Unfortunately we have had a high rate of returns due to failure on these and can no longer enthusiastically recommend them. Please consider our original rebuilt units. This is the large nut control valve that Ford switched to after 1967. Many 1967 Cougars have been converted to the 1968 valve over the years so you may want to double check your valve before ordering. These units are designed to use type F fluid, not off the shelf power steering fluid. Please follow the procedures for...

This unit was used only one year on the Cougar and is unique because of its smaller fitting (1/4") for the pressure hose. Many 1967 Cougars have been converted to the 1968 valve over the years so you may want to double check your valve before ordering. We highly recommend upgrading to the large nut (5/16") control valve as the small nut control valve posses a potential safety issue, thus the reason why Ford replaced it the following year. The small nut system was engineered dangerously close...

This windshield wiper delay governor mounts to the driver side firewall. To find where this mounts on the firewall, look for two dimples. Wiring is simple, unplug the windshield wiper harness and plug the male and female ends into the appropriate plugs on the controller. Sometimes called interval or delay wipers. *NOTE* Must be used in conjunction with a intermittent wiper delay switch.Part # C9ZB-17C476, MPC #'s C9ZZ-17C476-B or D0ZZ-17C476-B.

This is a used windshield wiper delay governor, or module, and is a black box that mounts under the dash to the left of the radio. Sometimes called interval or delay wipers. *NOTE* Must be used in conjunction with a intermittent wiper switch.Part # D1ZB-17C476, D2ZB-17C476, MPC # D1ZZ-17C476-A.

Reproduction front tack strip for the front bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the front bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 feet (60 inches) of material and will have to trim the tack strip to fit...

Galvanized three piece replacement tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

Reproduction stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Mustang. Ford part number: C9ZZ-7654676-A

This is the restored stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Mustang. This is a very hard part to come by in good shape. Many times body shops will lose this piece while replacing the top.Ford part number: C9ZZ-7654676-ATHIS ITEM WILL NOT SHIP UNTIL WE HAVE RECEIVED YOUR CORE. ...

Reproduction Convertible Brake & Fuel Line Clamp Kit for the 1970 Mercury Cougar - 1970 Ford Mustang 

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar. Check out the video on replacing your door panels below.

Reproduction Convertible Fuel Vapor Line Clamp Kit for the 1970 Mercury Cougar - 1970 Ford Mustang 

The decal I most often see on the 1971-1973 Cougar is the used one pictured here. Will be trying to locate this decal soon.

Currently, Convertible Tops dropshipped from this supplier will not ship for 4-6 weeks. The original tops would have been double texture PinPoint Vinyl. There are 3 different materials currently offered for these premium tops. Single Texture PinPoint Vinyl (GOOD): This is the material that is offered by almost all Mustang Vendors and it looks the same on the surface as an OEM top. It is often referred to as an OEM replacement, but that is not exactly accurate...This is a two-ply composite...

Currently, Convertible Tops dropshipped from this supplier will not ship for 4-6 weeks. The original tops would have been double texture PinPoint Vinyl. There are 3 different materials currently offered for these premium tops. Single Texture PinPoint Vinyl (GOOD): This is the material that is offered by almost all Mustang Vendors and it looks the same on the surface as an OEM top. This is a two-ply composite which has an outer layer of canvas-looking PVC vinyl plastic, and an inner layer of...