All Products

This never came on a Cougar, but it is a nice upgrade from the string that attaches your seat belt shoulder strap to the coat hanger when the shoulder strap is not in use. Fits all models except convertible. Originally, the shoulder strap connected to the bolt cover on one end, And to a string on the shoulder strap that connects it to the coat hook to keep it out of the way when not in use. This new hook slides into the track on the back of the moulding over the door, and is used instead of...

No damage original bolt. Sold individually, two required per car.

Used quarter window shoulder screw and nut for the 71 - 73 Cougar and Mustang.

All new parts for rebuilding the right and left shutoff butterfly in the air conditioning register vents. Fits all 1967-68 Mercury Cougar and Ford Mustang with factory A/C. Kit includes 2 knobs, 2 black butterfly vent doors, 2 shafts, and 2 retainers. All of these individual parts are also separately. Chrome vent registers and vent retainers are also available.

Driver side bracket that fits onto the rear radio bracket assembly on the 67 - 68 Cougar or Mustang equipped with a console. The bracket assembly is 3 separate pieces, this is for the driver side bracket only.

Passenger side bracket that fits onto the rear radio bracket assembly on the 67 - 68 Cougar or Mustang equipped with a console. The bracket assembly is 3 separate pieces, this is for the passenger side bracket only.

These pads go between the rear quarter panel and quarter panel reflector on the 1968 Mercury Cougar only. Sold as a pair.  Replaces Ford part #: C8WY-13493.*Note - These were not installed on Ford Mustangs, but they could be installed since they use the same reflector after Feb 15, 1968.

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Even the original LH decals will be in place! These are good quality parts ready to install on your Cougar. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side. ...

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Could have decals missing, and will have minor pitting. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side.

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Even the original RH decals will be in place! These are good quality parts ready to install on your Cougar. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side. ...

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps.Could have decals missing, and will have minor pitting. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side.

These are the caps placed on the inside of the rear marker reflectors to protect your trunk's contents from damage. These Reproductions are grey. They were originally black with varying shades of grey. Sold in pairs, two pairs per car. Click on images to enlarge. Here is the Rear Marker Reflector without a cap. Here is the new cap on the marker. After you install the Rear Marker, screw the cap onto the Marker from the inside of the trunk. Below is a good used cap on the Marker. ...

Nice reproduction rear body side reflector as found on 1968 Mercury Cougars. Used on Montego / Cyclone / Cougar for the 1968 model year. Great reproduction, but without the 'FoMoCo' marking like on our concours version. This reflector comes with the rubber gasket and attaching nuts. Very nice and at an attractive price. You'll also want these rubber protectors for the trunk.Replaces Ford part # C8GY-13380-A. *Note - Also fits 1968 Mustang after Feb 15, 1968. *Trivia - 1968 Mustangs did not...

Perfect in every detail down to the FoMoCo logo. Used on the 1968 Montego / Cyclone / Cougar for the 1968 model year. Great reproduction made from the original Ford tooling. This is the Concours version with FoMoCo marking on the lens. Listing is for the reflector only, does not come with gasket or hardware. Also, don't forget the rubber protectors that slip over the pointy studs inside the trunk. Replaces Ford part #C8GY-13380. ...

This pair of die-cast chrome front side marker bezels are sold as pictured with no socket, lens, lens gasket, bulb, mounting hardware or fender to body gasket, but all of these items are available here on our website. These side fender lights resemble "fine jewelry" when mounted on your freshly painted fenders... The fit and finish are very good but the hole in which the socket mounts is slightly larger than original which works well with our reproduction socket assemblies. If you are using...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Reproduction side marker light socket with harness set. For all 1968 Mercury Cougar and Mercury Montego and Cyclone. This listing is for a pair of wiring harnesses with light sockets. The original sockets were a snug fit in the fender light housings. These sockets are a slightly larger diameter than original and work well with the reproduction housings, but you may need to enlarge the hole if you're using your original housings. These wiring harnesses look real sharp with our reproduction...

Sold as a pair. These gaskets seal the lens to the light housing on the 1968 side marker lights found on the fenders of the 1968 Cougar.

The D0WY-15A434-LSM LED Side Marker Light Adapter kit is required when the C9WY-13A366-AL or the TS-400 Sequential controller is installed with LED front turn signal and LED side marker bulbs on most 1970 and up Ford vehicles. An adapter is required for each side marker light (4 total). This adapter solves the problem where the side marker voltage feeds back through the front turn signal bulb when the running lights or headlights are turned on. When this happens all the rear bulbs may flash...

The D1WY-15A434-LSM LED Side Marker Light Adapter kit is required when the C9WY-13A366-AL or the TS-400 Sequential controller is installed with LED front turn signal and rear LED side marker bulbs on 1971 Cougars and other Ford vehicles with two rear side marker lights. An adapter is required for each rear side marker light (2 total). This adapter solves the problem where the side marker voltage feeds back through the front turn signal bulb when the running lights or headlights are turned on....

Coming from Western parts cars these brackets are unusually nice in comparison to what you will find in other regions. For and extra $1.50 we can include the mounting nuts. Right is the same as left, two brackets required per car, sold individually.

Good used light with no pits or scrapes. Does not include lens or pigtail with socket, does include mounting bracket with two nuts. The chrome body carries a C8GB-15A428-B engineering number and the pigtail has a C8WB-15A442-A engineering number imprinted on the wire. We usually only have one or two in stock of this caliber so do not be surprised when you try to place this in your cart and it shows 0 quantity. Even though this is the best we will ever have to offer off of a Western parts car...

This grade "B" light bezel will have minor blemishes in the chrome as shown. Good part for a driver as it will not have deep pits. Does not include pigtail or lens. Left is the same as right. To remove pigtail from your existing light wrap socket in cloth to protect and grip firmly with a pair of pliers, rock back and forth while pulling and the plug and socket assembly should come right out from the back side. Replaces Ford part # C8WY-15A201-C.

Ford never offered this socket / plug assembly on its own but we do from time to time get one that has a clean socket and no cuts in the wiring. You can often just twist and pull (after the bulb has been removed) and it will come right out of the chrome housing. The Ford engineering number imprinted on the wire is C8WB-15A442-A.

Replaces C9AZ-15447. Sold as a set of four.

Replaces Ford part #C8WY-15447. Sold as a pair, two required per car. Right is the same as left.

Reproduction passenger side (right hand) floor pan cowl side panel for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your car!

Reproduction manually adjustable side view mirror in chrome for the Mercury Cougar and Ford Galaxie. This ambidextrous mirror works on either the passenger or driver side door and a gasket is included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side...

Fantastic quality in all respects, concours quality. Don't forget to select a mounting gasket and mounting kit if needed. Replaces Ford part # C7WY-17696-A.*NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere!Hole spacing: 4 3/8" Do you have riv-nut questions? Here are riv-nut answers! ...

Working grade "B" driver side (left hand) remote mirror with dull chrome. Don't have too high of expectation on this, it is 40 years old and comes from a car we most likely pulled from a brier patch...Hole spacing: 4 3/8" Do you have riv-nut questions? Here are riv-nut answers! ...

Working driver side (left hand) grade "B" remote mirror with dull chrome. Don't have too high of expectation on this, it is 40 years old and comes from a car we most likely pulled from a brier patch...

New Old Stock driver side (left hand) mirror that has never been installed. Since the wand is recessed into the door panel on the 1969 Cougar, the wand is not prone to breaking off like the 1970 version which protrudes straight out. Ford part number C9WY-17696-A NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the glass. This clip is hard to...

Reproduction driver side mirror lens replacement for the 67 - 68 Cougar chrome side mirror. NOTE: The narrow end of the mirror goes up top on Cougar and is reversed for Mustang. These mirrors are manufactured for the Mustang, so the small supplier part number at the bottom will be upside down and on top for Cougar. 

Reproduction manually adjustable convex passenger side view mirror in chrome for the Mercury Cougar or Ford Galaxie. Gasket and screws included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Here’s our little video that will make your mirror installation a little easier. ...

Finally! A correct looking and fitting quality mirror for the passenger side of your 1967-68 Cougar. This is NOT a Mustang part made to "kind of work". For years our customers have called almost weekly asking for the "RARE" 1967-68 right hand outside mirror listed in their owners manual as an option available at their local "Lincoln - Mercury Dealer". The intention may have been to offer one but it actually never came to be...   This product has been getting great reviews in the Cougar...

Finally! A correct looking and fitting quality mirror for the passenger side of your 1967 - 68 Cougar. This is NOT a Mustang part made to "kind of work". For years our customers have called almost weekly asking for the "RARE" 1967-68 right hand outside mirror listed in their owners manual as an option available at their local "Lincoln - Mercury Dealer". The intention may have been to offer one but it actually never came to be... This product has been getting great reviews in the Cougar...

Reproduction convex passenger side mirror lens replacement for the 67 - 68 Cougar chrome side mirror. NOTE: The narrow end of the mirror goes up top on Cougar and is reversed for Mustang. These mirrors are manufactured for the Mustang, so the small supplier part number at the bottom will be upside down and on top for Cougar. 

This mirror features a painted base which was used on the Sport Special and Eliminator models. XR7 models used a chrome base except the very late cars. Good used mirror ready to be painted and installed. We test the remote function before we send. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump...

Reproduction driver side (left hand) remote sport mirror for the Mercury Cougar XR7. This unit will come with a primered base and head so that you can paint it to match the rest of your car. If you have some good used 1970 mirrors for sale with or without the wand intact we would like to hear from you as these are getting very hard to find! 1970 was the first year you could get a factory installed sport mirror on your XR7, Sports Special, or Eliminator. If you would also like to have a...

If your mirror is fine except a broken off wand (control lever) it is an easy fix. Since the wand is made of a soft metal it is not too hard to drill out the old and replace it with one of our threaded replacement units. One can also remove the entire adjuster assembly form another mirror that has a broken base and carefully attach it. If you have some good used 1970 mirrors for sale with or without the wand intact we would like to hear from you as these are getting very hard to find. Have...

Good working used mirror with joystick intact and no cracks in the base. The mounting holes on the base are located 6 3/4" apart. Ford number inside the base D1WB-17743. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Do you have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

This reproduction remotely operated driver side (left hand) mirror is unique to the 1969 XR7 as evidenced by the chrome base. The Eliminator and Sports Special used a painted base, but in late 1969 the XR7 came with a painted base. This reproduction unit will come with the correct chrome base, but the head will be in primer for you to paint to match the color of your killer Cat. The XR7, Sports Special, or Eliminator never came with a passenger side (right hand) mirror from the factory, but...

This driver side (left hand) mirror is unique to the 1969 XR7 as evidenced by the chrome base. The Eliminator and Sports Special used a painted base. Good used mirror with good chrome and a working adjuster. In late 1969 the XR7 came with a painted base. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a...

1969 Driver side Sport mirror with rechromed Cougar base. Mirrors disassembled, and reassembled with our rechromed OEM Cougar mirror base. Obviously will need to be repainted, but will have a fresh chromed mirror base like on the 1969 XR7's. Comes as shown with used glass and working remote. Door panel bezels, door gasket, new glass, and nuts available separately. 

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a...

Fits and looks identical to the 1970 mirror base but is slightly taller. The difference in height between the two versions is indiscernible to the naked eye. Very nice product, works well with original mirror heads, save your hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road?...

Used passenger side (right hand) sport mirror for the Mercury Cougar Eliminator. The Ford service replacement part number for the complete assembly is DOOZ-17682-D with a casting # on the base that reads D0OB-17713-AW. This is the correct right hand mirror for your 1970 Eliminator. It was available over the Ford counter to be placed on any 1969-70 Cougar but the 1970 Eliminator is the only model that came from the factory with it. Unlike the driver side door there is no factory embossed area...