All Products

Replaces Ford part #: D2WY-6543720.

Nice fit! You will need new window gaskets if you plan on changing the headliner. If you are installing the gasket yourself, you will be needing a bedding compound, we like this one here. Replaces Ford part # C7WY-6542084. You can get a feel for what it takes to replace your rear window seal by watching our windshield replacement video below: ...

Excellent fit whether you are installing OEM thickness glass or repro which often is a slightly thinner gauge, must have when replacing either headliner or windshield. There have been multiple manufacturers of this seal over the years, this is the best fit in our opinion. Fits years 67 - 68 for Cougar and 65-68 on the Mustang. We also sell the bedding compound for the installation.  Replaces Ford part # C6ZZ-6503110-A. Keep in mind this is not a difficult do-it-yourself project, here's...

Replaces Ford part #D1ZZ-7602626

These vertical seals attach to the leading edge of the rear quarter windows and seal against the rear edge of the door glass. Sold as a pair.Replaces Ford Part #: C5ZZ-6530146 and C5ZZ-6530147. These are the budget or economy versions. We also sell concours versions.

These vertical seals attach to the leading edge of the rear quarter windows and seal against the rear edge of the door glass. Sold as a pair.Replaces Ford Part #: C5ZZ-6530146 and C5ZZ-6530147. These are the premium or concours versions. We also sell economy versions.

180 pages.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. 184 pages.

Intended for the Mustang, but much of the information will work for the Mercury Cougar

Reproduction Weld / Sealant Assembly Manual for the 1968 Ford Mustang.

Sold individually, phosphate & Oil (gray-black).

Used inner and outer driver side (left hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety.*Customer Feedback*"I know Don Rush is a trusted and well respected guy. I would just like to give my opinion of him and his team from a Cougar owner in the UK. On one end of the spectrum you have the low lives such as XXX XXXXX who will scam you at the drop of a hat. At completely the opposite end you...

Used inner and outer passenger side (right hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.Used inner and outer passenger side (right hand) wheel house...

Used inner and outer passenger side (right hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.*Customer Feedback*"I know Don Rush is a trusted and well...

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems for installation of the new Legendary aluminum wheels. These really only fit the Magstar style wheels; we recommend the 3/4" lug nuts for all the other Legendary wheels for clearance reasons. Conical Head: 13/16" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems. Specifically for installation of the new Legendary GT7 and 1966 Shelby wheels. Thread Size: 1/2" Bolt Pattern Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome lug nuts and 4 chrome valve stems for installation of the new aluminum Legendary Series wheels. Tapered for correct fit. This 3/4" size is what we recommend you use with the Legendary wheels, since the clearances are too tight for 13/16" nuts. Conical Head: 3/4" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2" stud with correct 1/2 x 20 threads. These are slightly longer in length than the stock ones, this will allow the alloy wheels to fit the Classic Cougars.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide.This ring will have one or two small scratches or dings that will be noticeable. Replaces Ford part number D0DZ-1210-A.Fits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972 Ford...

Used on the 1970 Ford Mustang, 1970 - 1971 Cyclone and Torino and 1971 Cougar style steel wheel 14 x 7". Master Parts Catalog description: 15-1/4" O.D., 11" I.D., 2-3/4" wide. This ring will have one or two very small scratches or dings that will not be easily fixed, driver quality.Ford part number D0ZZ-1210-BFord superseded this part with part number D4WY-1210-A

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

Used grade A trim ring for a 1967 Cougar style steel wheel. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep, one year only wheel. Looks very similar to the 1968 SS wheel. No dings or scratches that cannot be buffed out. sold individually.Replaces Ford part number C6ZZ-1210-A.

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, and most customers will be happy with our reproduction ring that is not brushed....

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have slight blemishes that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, most customers will be happy with our reproduction ring that is not brushed. This...

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have one or two very small scratches or dings that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

This trim ring was used in 1967 and is very close (not as deep) to the 1969 - 1970 trim ring. 1968 was deeper and was brushed on the inner portion. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep. Ford Part number C6ZZ-1210-A.

Reproduction aqua headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction aqua rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction black rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Aqua windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Black windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. See separate listing for color windlace. Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Blue windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Ivy Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Light Blue windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Light Ivy Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Nugget Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Saddle windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

White windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Reproduction dark blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction dark blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction dark red headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...