All Products

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: C5ZZ-9A702.

Great little kit that is a big time saver! Correct in detail, every 40 year old Cougar needs this kit! Replaces Ford Part #: C5ZZ-9A702-MK.

Correct texture Gas Pedal, includes stainless steel trim.

Reproduction Accelerator Pedal for the 1969 and 1970 Mercury Cougar

Nice new black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Replaces Ford Part #: D1ZZ-9735 and D1ZZ-9735-A

Black moulded plastic pedal pad for all 1967 and 1968 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C5ZZ-9735-A.

Black moulded plastic pedal pad for all 1969 and 1970 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C9OZ-9735-A.

Black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Ford part number: D1ZZ-9735 or D1ZZ-9735-A Stainless surround trim available too, part number D1ZZ-9735-B.

Accelerator pedal assembly that mounts to the engine firewall. For use with any 1969 Cougar or Mustang WITHOUT factory cruise control.

Reproduction Concours Correct throttle return spring.Replaces Ford Part # : C9ZZ-9737-A

Concours Throttle Return Spring for the 390 / 428CJ / 428SCJ Manufactured after 4-9-69

Correct spring, black phosphorus plated. Does not have the same tension as original spring. We also have a Concours spring that has the correct tension. Replaces Ford Part #: C5ZZ-9737-B.*Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1967 Mercury Cougar and 1964 - 1967 Ford Mustang with 289 engines. Ford part number C5ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Good reproduction of the 1967 throttle rod for 289 engines. It will fit on 1968 with any 289 or 302 engine with Ford Autolite carburetors. Will also fit most Holley and Edelbrock carburetors too. We also sell used versions of both 1967 and 1968 small block throttle rods. Consider also purchasing a linkage clip, see related items.Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all...

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with 289 or 302 engines. Ford part number C8ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. Ford part number C8WY-9A702-A *Note - Before 12/11/1968. *Note - not for use with factory cruise control.

Concours Correct Throttle Linkage Rod, 13 1/2" long, S code 390-4V, W code 427-4V, and R code 428CJ with factory 4 barrel HOLLEY carburetor, with out speed control.Replaces Ford Part # C8ZZ-9A702-A

Clip for mounting the throttle linkage rod rod to the carburetor and mounts C-4 or C-6 throttle cables to the throttle bell cranks.Replaces Ford part number C2VY-9826-A.

This correctly formed carburetor throttle solenoid idle bracket for the 1970 428CJ engines on any Mercury Cougar or Ford Mustang. This is a nice reproduction item.Replaces part # D0ZZ-9B550-A.

This correctly formed carburetor throttle solenoid idle bracket for the 1970 428CJ engines on any Mercury Cougar or Ford Mustang. This is a nice reproduction item.Replaces part # D0ZZ-9B550-A.

This is an accurate reproduction of the tie down notice decal that was placed on the rear license plate frame. This was to remind dealers to remove the tie down plates that were used to secure the cars to the transport trains / trucks on their way from the factory to the dealers. Ford wanted to recycle these plates to save money, but dealers often didn't feel it was worth their time to remove the plates. Thus, many cars still have them. Check yours out! ...

Inner tie rod end for 1967 - 1969 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: C7ZZ-3A131-A

Inner tie rod end for 1971 - 1973 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: D1ZZ-3A131-A

Outer tie rod end for 1967 – 1969 Mercury Cougar and Ford Mustang with either power steering or manual steering and with drum or disk brakes. Quality reproduction part. Sold individually, two needed per car. Made in the USA. Replaces Ford Part #: C7ZZ-3A130-A. *Note – Excludes 1969 Boss 302 Eliminator and Mustang. *Note – Use 1970-73 arm for vehicles with the 'Granada' disc brake conversions.

Outer tie rod end for 1970 – 1973 Mercury Cougar and Ford Mustang with either power steering or manual steering and with drum or disk brakes. Quality reproduction part. Includes 1969 Boss 302 Eliminator and Mustang, and 1970-74 Ford Maverick and Mercury Comet. Sold individually, two needed per car. Made in the USA. Replaces Ford Part #: D0OZ-3A130-B.

Reproduction rubber dust seal or boot for front suspension upper and lower tie rod ends. 1970-73 Mercury Cougar, Ford Mustang, and many other Ford cars.Replaces Ford part # D0OZ-3332

These differ from 68-69 in that there is no starter safety switch embedded in them. This is a used part, tested, lubed, and working. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.

Used timing chain cover with casting number C5OE-6059-A, for any 1965-67 289 engine. 1967 Mercury Cougar and 1965-67 Ford Mustang. This timing cover has a built in timing pointer as part of the casting. Cast aluminum construction without excessive damage. Find the installation bolt kit here. Replaces Ford part number C5OE-6059-A.

Used timing chain cover for any 289 / 302 / 351W engine from 1968-70 Mercury Cougar and Ford Mustang or most any 1968 Ford with 289 or 302. Cast aluminum construction without excessive damage. Installation bolt kits also available. Sometime during the 1969 model year, the timing chain cover number changed to C9OE-6059-A. So either one will interchange. Replaces Ford part number C8AE-6059-A.

Used timing chain cover for any 351C or Cleveland engine from 1970-74. Mercury Cougar and Ford Mustang and additionally fits 351M / 400M engines. All steel construction without excessive rust or damage. Installation bolt kits also avialable.Replaces Ford part number D0AZ-6B070-A.*Note - will not fit 351W or Windsor engines.

Used timing chain cover with casting number C3AE-6059-A, for any 1967 390 engine. 1967 Mercury Cougar and 1967 Ford Mustang. Cast aluminum construction without excessive damage. Installation bolt kits also avialable.Replaces Ford part number C3AE-6059-A.*Note there is a different version of this timing cover for 1968-70 390/428CJ engines.

Used timing chain cover for any 390 or 428CJ engine from 1968-70 Mercury Cougar and Ford Mustang or most any 1968-70 Ford with 390 or 428 cubic inch engines. Cast aluminum construction without excessive damage. Installation bolt kits also avialable. Ford casting number C8AE-6059-B. *Note - Is not technically compatible with 1967 or earlier 390 engines.

Folks, this one just doesn't fit. Probably fits a 1973 or later 302 Ford, but not on the Cougar? The crankshaft center hole is 2-9/16 inches, the originals were just over 2 inches in diameter. Timing Cover not for 1967-1969 289/302/351W using a water pump with a backing plate. Features a cast-in timing pointer and dipstick hole.

Set of 6 bolts for installing an OEM Ford timing cover marked C5OE-6059-A, which originally came on all 1967 Mercury Cougars with 289 engines or 1965-67 Fords including Mustang with 289 engines. 5 short and 1 long bolt in this kit.

Set of 6 bolts for installing an OEM Ford timing cover marked C8AE-6059-A, which originally came on all 1969-70 Mercury Cougars with 289 / 302/ 351W engines or 1968-70 Fords including Mustang with 289 / 302/ 351W engines. 4 short and 2 long bolt in this kit.*Note this kit is not applicable to the early designed Ford timing cover, see related items for other kit.

Set of 3 bolts for installing an OEM Ford timing cover, which originally came on all 1970-73 Mercury Cougars with 351C or Cleveland engines or 1970-74 Fords including Mustang with 351 Cleveland engines. Also fits 351M and 400M Ford engines*Note - this kit is not applicable to the 351W or Windsor engine. See related items for other kit.

Set of 10 bolts for installing an OEM Ford timing cover marked C3AE-6059-A, which originally came on all 1967 Mercury Cougars with 390 engines or 1963-67 Fords including Mustang with 352 / 390 / 410 / 428 engines. 10 total new bolts.*Note - this kit is not applicable to the 1968 and later Ford FE timing covers. See related items for other kit.

Set of 10 bolts for installing an OEM Ford timing cover marked C8AE-6059-B, which originally came on all 1968-70 Mercury Cougars with 390 / 428CJ / 427-4V engines or 1968-70 Fords including Mustang with 352 / 390 / 428CJ engines. *Note this kit is not applicable to the 1963-67 designed Ford FE timing cover, see related items for other kit.

Stamped Steel Pointer Mounts to Timing Chain Cover. Black Zinc-Plated. Includes Mounting Screw. Correct for 289, 302 and 351W Mercury Cougar or Ford anything including Mustang. We know the other vendors claim this part to fit 1967-73, but it doesn't. Works with 1968-69 Ford timing covers and with 1968-69 Ford 3 bolt harmonic balancers. Starting in 1970, Ford V-8 engines for Mustang and Cougar had timing pointers installed on the passenger side of the engine, and used harmonic balancers with 4...

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1968-69 Mercury Cougar and Ford Mustang 289, 302, and 351W Mercury Cougar or Ford anything including Mustang. We know the other vendors claim this part to fit 1967-73, but it doesn't. Works with 1968-69 Ford timing covers and with 1968-69 Ford 3 bolt harmonic balancers. Starting in 1970, Ford V-8 engines for Mustang and Cougar had timing pointers installed on the passenger side of the engine, and a companion harmonic balancer with...

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in most 1970-72 Mercury Cougar or Ford anything including Mustang. Can be used on any 1970-74 351C engine from Ford. Technically, 1972 California 351C cars and 1973 351C cars used a different timing pointer for what ever reason. Replaces Ford part D0AZ-6023-A.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in any 1973 Mercury Cougar or Ford Mustang. Technically, 1972 California 351C cars and 1973 351C cars used this timing pointer. Part stamped with casting number D2AE-6023-BA. The smaller more common version will also fit and look better in our opinion. Replaces Ford part D2AE-6023-BA.

Used stamped steel pointer mounts to timing chain cover. Correct for 1967 Mercury Cougar or Ford Mustang with S code 390 engine. Must be used with the 1967 style timing cover.

Concourse Correct Timing Pointer for the 1968 - 1970 390, 390GT or 428CJ. Technically, by design, this is a copy of a 1969-70 390/428CJ timing pointer. It will also work for 1968, since the harmonic balancers and timing covers are the same.Replaces Part # C9AZ-6023-A.* Note - not correct for 428 Super Cobra Jet, see related item.

New Old Stock Timing Pointer for the 1968 - 1970 390, 390GT or 428CJ. Fits all 1969-70 Mercury Cougar, Ford, and Mustang, with 390/428CJ. It will also work for 1968, since the harmonic balancers and timing covers are the same. Replaces Part # C9AZ-6023-A. * Note - not correct for 428 Super Cobra Jet, see related item.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1969-70 Mercury Cougar and Ford Mustang with 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Ford part number C9AZ-6023-A. * Note 428 Super Cobra Jet uses a different pointer, see related.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1968 Mercury Cougar and Ford Mustang with 390-2V, 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Reproductions are nice, but they are a copy of the 1969-70 timing pointer. Close, but no cigar. Replaces Ford part C8AZ-6023-A.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1969-70 Mercury Cougar and Ford Mustang with 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Replaces Ford part C9AZ-6023-A.* Note 428 Super Cobra Jet uses a different pointer, see related.