All Products

Looped weld in retainer for the rear seat installation on any 1967-70 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets. We think that the Ford number is C5AZ-6263370-B, but we have not been able to verify this for certain. For sure that basic Ford part number is 63370. ...

Hook bracket weld in retainer for the rear seat installation on any 1971-73 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. Sold individually, two required per car. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets.  The Ford number is C9AZ-6263370-A.

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged.  Check out our video "All about seat belts" below. ...

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

New Old Stock. This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

For power or manual drum brake Cougars. Late production brake lines were routed under the steering column.

For power or manual drum brake Cougars.Late production brake lines were routed under the steering column.

72 - 73 Mercury Cougar and Ford Mustang Front Drum Intermediate Brake Line made of OE-style steel. Intermediate Brake Lines are the lines running from the front of the car to the back feeding your rear brakes. These lines will run along your chassis all the way back to the rear brake drop hose. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. ...

For power or manual drum brake Cougars.Early production brake lines were routed 'over' the steering column.

Early production brake lines were routed 'over' the steering column.

Reproduction 22" pigtail for the 67-69 front turn signal wiring harness. Please Note: The Cougars are wired differently than some Mustangs. On some Mustangs the brown wire goes to a male plug.   This plug is a reproduction of the Cougar plug. Here is an example from the reproduction tail light we sell showing the difference: For installation on a Cougar, match up: Black Wire Black Wire Light Blue Wire Light Blue / Off White Wire Brown Wire Brown Wire ...

***WARNING*** Plugging these directly into a Cougar wiring harness without correctly re-wiring in the pigtails may fry your wiring harness! Reproduction driver side (left hand) and passenger side (right hand) front turn signal / parking light assemblies for the Ford Mustang. The plug is not correct for the Mercury Cougar's wiring harness and will need to be changed to work properly. However, this is an easy straightforward process which we lay out below. Plus you can save a good amount of that...

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, sold individually. Replaces Ford part #: C5ZZ-13207-B.

Used driver side parking light / turn signal retainer. Ford part #: C5ZZ-13207-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, sold individually. Replaces Ford part # C5ZZ-13206-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used passenger side parking light / front turn signal retainer. Ford part # C5ZZ-13206-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Stamped steel and and zinc plated to prevent rust. Fits behind the parking lamps, Sold as a pair. Replaces Ford part #: C5ZZ-13206-B and C5ZZ-13207-B.

Reproduction driver side (left hand) and passenger side (right hand) front turn signal / parking light assemblies for the Mercury Cougar. These units come with the correct amber bulbs, clear lenses and have the original working wiring pigtails already spliced in. These are sold as a pair only. Keep in mind there were slight variations between 1967 and 1968 (a simple A clip on the wiring harness). We no longer carry both versions, we use the same wiring on both years. If you would like to...

Made from original Ford tooling, perfect in every detail down to the FoMoCo logo. Sold individually, two required per car. Clear lens for 1967-68 Mercury Cougar, Amber lens for Mustang. Screws sold separately, you can find them here. Replaces Ford part # C7WY-13208-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

Reproduction Front Valance Bolts & U Nuts for the 1968 Mercury Cougar 

D0WY-9A091-A Front evaporative vapor separator, mounts in the drivers side trunk well. *Note - This is only a small part of the 9B004 assembly.

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, it will fit perfectly as well. Planning on installing the glass yourself? We also sell the glass to window channel weld.BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate...

Reproduction brake line clamp kit for the Mercury Cougar or Ford Mustang.

Replaces Ford Part # 359747-S

Used factory installed vented fuel, or gas cap as installed on 1967-69 Mercury Cougar 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap.We stock these in limited quantities, and will have an intact paper gasket. Correct "VENTED" embossed and has the "S" stamped onto the center rivet. Price is established by demand, and these normally are only needed for very high level restorations or strict concours judging...

Driver quality complete assembly with average chrome, emblem and cracked lens.

Reproduction ribbed aluminum foil backing plate for the gas doors on the 1969 and 1970 Mercury Cougar and XR7 models.

Original part removed from an Eliminator parts car many years ago. The frame is the same as the 69-70 common fuel door with 2 extra holes drilled, the cat emblem is the same as what is found on a 1970 Standard / Eliminator Cougar center grille. On the units that have a faded background foil, we gently remove the emblem and replace the black foil with a reproduction. Keep in mind we do not retake pictures each time we get a different unit in stock (which is seldom).This will work on any 69-70...

Good used fuel door framed insert, without the crest as shown. These in most cases will not include the thin foil backing plate as shown. "A" grade will have minor rust pitting and some dullness on the chrome, overall very good used.Foil backing plate available in reproduction, see related items.

Fair used fuel door framed insert, without the crest. These most often will not include the thin foil backing plate as shown. "B" grade will have some rust pitting and some dullness on the bright work, overall fair used. Foil inserts available used in limited quantities.

Restored fuel door framed insert without the background decal or crest, for the 1969 - 1970 Mercury Cougar. Foil backing plate available in reproduction. At the moment there are no reproductions on the walking cat, you can however polish up your old cat and re-use it in this frame.

New Old Stock gas door. Fits all 1969-70 Mercury Cougars. Ford part number C9WY-65405A26-A

Used gas door with hinge spring. The black painted door as shown in the picture is a service replacement fuel door. Used doors are bare steel and will come with the hinge and spring.  Ford part number C9WY-65405A26-A

This filter ONLY fits the following 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19.

This filter ONLY fits the following Ford Holley 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. This is a service replacement filter, it has D2AE-9155-AA stamped on the body of the filter. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19 and C9AZ-9155-B,  FG-39.

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C5ZZ-9327-A.