All Products

Bracket that holds the throttle cable for the G code Boss 302 Cougar Eliminators. This is a 1970 part number, it is possible that the 1969 bracket may be either different or had a C9ZZ-9741-? part number. Will update when we verify, comments welcome. 1970 Ford part number listed as D0ZZ-9741-A.

These are the U-shaped brackets that hold the round part of the rear sway bar. These mount to the rear frame rail. All 1970 - 1973 Cougars should have these mounting holes from the factory, 1969 and earlier Cougars do not have these holes. Two clamps needed for installation.

Reproduction pair of mounting nuts for any 68 - 70 Cougar or Mustang with power brakes.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Reproduction mounting bracket. This is the mounting plate for the end links on the factory rear sway. Mercury Cougar 1970-73 only, this is not a Mustang part. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates get sandwiched between the shock mounting plates and the Isolator clamps on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. The total width of this plate at its very...

This is the mounting plate for the end links on the factory rear sway bar. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates get sandwiched between the shock mounting plates and the Isolator clamps on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. The total width of this plate at its very widest part is 7 7/8". Found on all 1970-73 Mercury Cougar with factory competition...

Used mounting bracket. This is the mounting plate for the end links on the factory rear sway bar. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates are mounted with the shock mounting plates on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. Replaces Ford part number D0ZZ-5A775-A.NOTE: These are only a few of these in stock, and they will have moderate pitting.Mustang...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang. Original Ford part number C8MY-1424-A. About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels.

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

Plate for mounting the spare tire. 4 inches outside diameter with the 3 tabs.

Pair of used assembly line installed 1970 Mercury Cougar Eliminator rear spoiler brackets. Brackets only, no fasteners or spacers. Sold as a pair as shown, right and left side brackets. Can only be used with 1970 trunk lids. 1970 trunk lids have a slot cut out on each side for locating the rear wings. Not used on the 1969 Cougar Eliminator.We also stock the reproduction kit which includes fasteners. See in related items.

Aluminum spacer for the alternator mounting bracket on 1971 Mercury Cougar and Ford Mustang with 429 Cobra Jet engines. Also fits 1970-71 Cyclone and Torino with 429CJ engines. Spacer measures approximately 2-7/8 inches long. Fits between the engine and alternator mounting bracket.

These spacers are required to properly mount the trunk lock housing to the trunk. Two required per car, sold individually. Ford part number C7WY-6543565-A. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found on cars with 427-4V, 428CJ, 429CJ, Boss 302, Boss 351, or Boss 429. These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: 8L27, November 27, 1968; 0E29, May 29, 1970. Please have your desired date in mind when calling or place it in the comments section of your on-line order. We have removed the peg leg gears and parts...

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Replacement nozzle for the side window channel 3M bonding adhesive. After a short time

Dash pad attaching nut 8-32 threads original zinc plate and dichromate. 5 of these nuts are used to attach the dash pad to the painted steel upper dash panel  (D1ZZ-65044D90-A) on 1971-73 Mercury Cougar and Ford Mustangs. Sold individually.Replaces Ford part number 45271-S36.

Used stamped nut for attaching the tail light bezels to the tail light housings. This is a 8-32 nut, with a 11/32" hex and is intended for the 8-32 threaded studs attached to the tail light bezels on any 1967-68 Mercury Cougar. Sold individually, 10 per side, or 20 per car.Replaces Ford part number 45203-S.

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang

Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This black painted push on oil cap was on California sold cars with closed emissions systems. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a chromed version was also available with engine dress up kits.

Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This chromed push on oil cap was used on the DGS package or engine dress up kit which included chrome valve covers and air cleaner lid. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a Black painted version was also available on most 289 engines sold in California. This icon means that we're looking to buy...

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Precision machined to the factory specifications. Light gold anodize finish just like the original.

Factory oil cooler as used on 1969-70 R and Q code Super Cobra Jet 428 engines. Nice used condition, comes as shown with one fitting. Will also work for installing an external oil cooler on the other FE motor applications.Ford part number C9OE-6884-B. 

Nicely chromed dipstick tube and dipstick for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor. Replaces Ford part # C9OZ-6750-A or D0AZ-6750-C.

Chromed engine oil dipstick as found on all 1970 Mercury Cougar and Ford Mustang with 428CJ engines (Q or R Code). Top of shield to dip stick is 20 inches. The handles were chromed originally. Ford part # D0OZ-6750-C, Ford casting # D0OE-6750-C.*NOTE* This is an improved dipstick that better reflects the actual full mark, from previous 428CJ dipsticks.

Chromed engine oil dipstick as found on all 1971 Mercury Cougar and Ford Mustang with 429CJ engines (C or J Code). Top of the shield to the dip stick is 16.23 inches. The handles were chromed originally. Ford part # D0OZ-6750-B, Ford casting # D0OE-6750-B.*NOTE* This is not the same dipstick as found on garden variety 429 and 460 engines.

Chromed engine oil dipstick as found on all 1969 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engines (G Code). The handles were chromed originally. Ford part # C9ZZ-6750-A, Ford casting # C9ZE-6750-A.

Chromed engine oil dipstick as found on all 1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engines (G Code). The handles were chromed originally. Ford part # D0ZZ-6750-B, Ford casting # D0ZE-6750-C.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Reproduction blue dipstick tube for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

The oil filter made by the original Ford supplier.

New Old Stock oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

A nice reproduction oil pan in Chrome finish for the 351C. Replaces Ford Part #: D0ZZ-6675.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

Includes drain plug.

Used oil screen pick up tube assembly from a 1970-74 small block 335 series, or 351C or Cleveland Ford car. This is for front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: D1AZ-6622-A

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

Very rare find. Notice how unlike the reproductions the Mercury Head is fully raised. Ford part number C9WY-8213-A , casting number is C9WB-8B369-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Rare find in NOS condition! These are new, never used original manuals and no reproductions have been made. Limited quantity.

This is the second printing so it does include the xr7 package.

Reproduction Owners Manual for the 1968 Mercury Cougar