All Products

FYI: We do not plate, paint, or prep the backside of these bumpers as they were not done that way from the factory. (Above are examples of the mirror-like shine you can expect. 1969 front bumper shown out in the sun.) These are very sought after and a rare find without the impact strip holes, therefore we cannot guarantee we will have a core available for purchase. These bumpers are re-chromed using the triple plating process. This produces a significantly higher quality finished product...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Reproduction rubber bumper / stop that sits atop the vertical center grille support on the 71 - 72 Cougar. Most times, the originals are very brittle and crumble when you handle them so it might be a good idea to replace them at one point.Sold as  pair.

Mounts on floor pan above the center of the rear axle over 3rd member on small block cars with 8 inch rear ends. Mustang only, will not fit a Cougar.Replaces Ford part #: C5ZZ-4730-B orC3AZ-4730-B. Customer Comment:Thank You Don and WCCC,Copy Cat's almost done!Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product.Without their patience and understanding along with a great selection of parts I wouldn't have her in such great shape.Thanks guys, along...

THIS KIT HAS A CORE CHARGE OF $950 Here is a time and money saving package deal for the person restoring their 1967 or 1968 Cougar. This package includes: Hood lip moulding Fender extension mouldings Quarter extension mouldings Grille center trim Deck lid moulding Drip rail mouldings Nine piece front and rear window trim Front and rear Award Winning Bumpers All parts are show quality. The bumpers are triple plated chrome, the aluminum has the correct anodized finish just like NOS and the...

This is a complete kit for front and rear. If you own a 71 - 73 and then you will need two more bolts. mercurycougar.net: I was in Salem on business Monday when I decided to give West Coast Classic Cougar a call. Don was gone but Lin was there, talk about a nice guy I looked around the shop and Lin got me the parts I needed for my 68 Coupe. I am sure Lin was busy but he took the time to answer any questions I had, swapped a few stories and gave me a real good deal. I recommend anyone needing...

C9WY-17755-A Front bumper mounting bracket, 1969-70 Mercury Cougar driver side.

Complete five piece set includes the horizontal support as well as the two braces inside the trunk, two brackets that bolt to the bumper and hardware. Checked closely for bends, cracks and stripped threads. What is pictured is the best of what we have, we also have B grade sets that will clean up fine. Pair of inside the trunk bumper mounting brackets D3WY-17A750-A. Passenger side bumper bracket D3WY-17787-A, driver side bumper bracket D3WY-17788-A. Rear bumper center reinforcement beam...

D1WY-17C838-A Deflector or driver side bumper filler, 1971-72 Mercury Cougar. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts...

Rear bumper filler for any 1971-72 Mercury Cougar. No chips or cracks. Comes with fasteners. Replaces Ford part number D1WY-17808-A . * Note - Will not fit 1973 Mercury Cougar.

Rear bumper filler for any 1971-72 Mercury Cougar. No chips or cracks. Does not come with fasteners or clips. See related items for new aftermarket style clips for attaching, 8 total are needed. Replaces Ford part number D1WY-17808-A . * Note - Will not fit 1973 Mercury Cougar.

Used driver side (left hand) bumper guard for the Mercury Cougar. The chrome plating was pretty low quality back in the day and this unit will show some scratches and pitting as it is an almost 50 year old original part.Ford part # C7WY-17997-A for the driver side.

This optional front bumper guard was unique to the 1969-70 Mercury Cougar. These are sold individually and the passenger side (right hand) is the same as the driver side (left hand). keep in mind the factory did not put a high polish on these so NOS usually looks a little wavy and dull. No rear bumper guards were offered in the 1969-70 model years, only fronts. If you have cores to exchange on this NOS part we will take them for credit.Ford part Number: C9WY-17996-A This icon means that we're...

Used passenger side (right hand) bumper guard for the Mercury Cougar. The chrome plating was pretty low quality back in the day and this unit will show some scratches and pitting in the chrome as this is an almost 50 year old original part.Ford part # C7WY-17996-A for the passenger side. ...

Rare find, NOS rubber rub strip for the front bumper guard on 1971-72 Mercury Cougar. These hard rubber bump strips attach to the front bumper guards with 2 studs from the back side. Sold individually, right is the same as left, Ford Casting number as found on the back is D1WB-17A812-AB

D3AZ-17A812-A Front bumper guard rubber pad used prior to September 5, 1972, on a 1973 Mercury Cougar. The early front bumper guards had a narrow rubber pad early on. The rear flat surface measures 3/4 inches wide. Same rubber strip either right or left side. Hard to find without some scaring on the rubber. This pad is not nearly as common as the wider one which measures about 1-1/8 inches wide.Replaces Ford part number D3AB-17A812-A.

D3AZ-17A812-B Front bumper guard rubber pad used after September 5, 1972, on a 1973 Mercury Cougar. These later front bumper guards have a rubber pad that measures 1-1/8 inches wide on the flat rear surface. Same rubber strip either right or left side. Hard to find without some scaring on the rubber. This pad is more common than the thinner 3/4 inches wide pad.Replaces Ford part number D3AB-17A812-B.

Also referred to as "Bumperettes", this kit was available as an over the counter option for your 1967 or 1968 Mercury Cougar. According to Kevin Marti's book, "Cougar By The Numbers" 15,018 Cougars received rear bumper guards from the factory in 1968, that data is not listed for 1967 but it is assumed that the numbers are about the same. Keep in mind that the installation of this kit requires drilling two holes in your rear valance, for an example please check out our used valances in the...

New old stock rubber fender to hood bumpers. Set of 4 NOS Ford. Replaces Ford part #: C6OZ-16758-A.

(7526) Nylon plastic injected. New Old Stock. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where...

New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...

D1ZZ-6523258-A Black plastic bolt-in door glass bushing. Used on 1970 bolt in door glass and 1971-73 door and quarter glass. White was used in early 1970, and black from 1970-73. There was some overlap in 1970. ...

Used plastic bushing for the lock pawl rod guide for the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. These delicate little bushings are needed to keep the lock pawl rod in alignment with the vacuum motor shaft. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

[No Description Provided]

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

Reproduction ram cylinder bracket bushings for the 68 - 70 Cougar or Mustang. If you're having trouble with the bushings on your car ripping or tearing through the hole in your power steering ram cylinder bracket (more so with our reproduction drop down bracket), you can purchase this pair of polyurethane bushings to replace your existing ones. The boot kit we sell also comes with similar bushings, but are a lower quality item, so this set should solve your problem. Sold as a pair. ...

C60Z-6222454-B door handle hardware kit for 69-70 Cougar as well as select Torino / Fairlane / Cobra / Falcon

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

C9ZZ-2853-A Front emergency brake cable for all 1969-70 Mercury Cougar and Ford Mustang. Front cable attaches to the emergency foot brake. New Old Stock, measures 43-5/8 inches long.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

This reproduction rear emergency / parking brake cable kit fits from equalizer to rear brakes. 2 required per vehicle. Equal length emergency brake cables for 1967 on both the Mercury Cougar and Ford Mustangs. Upgrading to the 1968 unequal length cables can easily be done. Equal length cables is correct for 1967 Mercury Cougar and Ford Mustangs. Fits L.H. or R.H., the Cougar uses a longer keeper than the Mustang to compensate for the added wheel base length. Replaces Ford part # C7ZZ-2A635-A,...

This is our heater cable for use with Mercury Cougars and Ford Mustangs with factory equipped A/C. The best part, its NOS, so you know it will fit right the first time! Ford part # C9ZZ-19988-A.

New Old Stock cable for any 1971-73 Mercury Cougar. Cable only, handle needs to be replaced from your unit. Drift pin hold it onto the cable. Reuse your bezel too. Ford Part Number: D1WY-2760-A or D1WY-2A760-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

NOS heater cable for 1969 - 1973 Cougars or Mustangs that are not equipped with factory air conditioning.Ford Part #: D1ZZ-18518-A

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.

Very rare find in the original service replacement boxes dated 10-07-75. Sold as a pair.Ford part # C8WY-65502B20-A.Click on images to enlarge. ...

Used passenger side (right hand) disc brake caliper mounting bracket that is a unique and one year only bracket for mounting the Kelsey Hayes twin piston caliper to the 1967 Cougar brake spindle. Tough parts to find in rebuildable condition. We won't always have them in inventory as singles unless we have multiples of these extra brackets for one side or the other. Ford part # C7OZ-2B134-A.

1967 289-2V Autolite 2100 carburetor, manual transmission - 49 states. C7DF-E stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and manual transmissions. *Note - Not for DSO 52 or DSO...

1967 289-2V autolite 2100 carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base, 1.02" venturi size and 240 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note - Not for DSO 52 and DSO 53 California destined cars. ...

1967 289-2V Autolite 2100 carburetor, manual transmission - California DSO 52 and 53. C7DF-G stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and manual transmissions. *Note - For...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-H stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-N stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-2V carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base 1.14" venturi size 300 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note not for DSO 52 and DSO 53 California destined cars. *NOTE - Take a kid for a ride in a classic...

1967 289-2V Autolite 2100 carburetor, manual transmission - 49 states. C7DF-S stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Note - Not for DSO 52 or DSO 53 cars destined for California. *NOTE* Take a...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-V stamped on the carburetor base, 1.14" venturi size 300 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1968 390-2V Autolite 2100 carburetor, automatic C6 transmission - All 50 states. C8WF-A stamped on the carburetor base. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. X code engine 390-2V premium fuel. *Trivia every single X code 390-2V Cougar was an automatic, no manual transmissions what so ever.