All Products

Reproduction 2 screw rear mount sun visor bracket is only available in black, so plan on painting this unit to match. We have most other unfaded colors in used. Replaces Ford Part #: D1AZ-6504132-A or D3AZ-6504132-A.

Used 2 screw rear mount sun visor bracket for the Mercury Cougar or Ford Mustang coupe. The MPC lists other part numbers such as D1ZZ-6504132, D2ZZ-6504132, and D3AZ-6504132, which are specific to some colors, but we have yet to seen them in a car. The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, so mention it in the 'comments' section of your order. Ford part # D1AZ-6504132,...

For the purists out there we have a very limited amount of used moon crater visors that have no impressions, seam separation and minimal rust on the clips if any.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually.

Reproduction Moon Crater Sun Visor for the 1967 and 1968 Mercury Cougar / Ford Mustang. Visors are fully padded and covered with the correct textured moon skin to match the headliner. Sold as a Pair. Nugget Gold is not available in Moon Skin Crater, it is only available in a smooth vinyl.

Gray plastic rod with rubber visor tip. Fits most 70's cars built by Ford. Replaces Ford Part #: D3AZ-6504114-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it wasn't on there computer. At WCCC they said they were not sure but looked...

Visors are fully padded and covered with the correct vinyl or textured tier to match the headliner. Sold as a Pair.

For the purists out there we have a very limited amount of used visors that have no impressions, seam separation and minimal rust on the clips if any. Convertible and Coupe are the same.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.

This decal was sometimes placed on the dash face pad near the middle or right side, and sometimes on the sun visor.

This 4 1/2" long flexible drive cable connects the Bosch "sardine can" motor to the gear box drive assembly. Limited supply. Check out this vintage XR7G television commercial ...

Used 1968 Mercury Cougar sunroof motor access panel. This panel is covered by the headliner, but can be dropped down (headliner is glued to the panel) to access the sunroof motor. Will always have a multiple, repairable cracks, but is still functional.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Used support bracket for the hood latch on any 1967-68 Mercury Cougar. L shaped support bracket goes on top of the hood latch assembly. It also attaches to the radiator core support.Ford part number C7WY-16707-A.

Used Driver Side Grade B Center Grille Support for the 1969 Mercury Cougar

Used Passenger Side Grade A Center Grille Support for the 1969 Mercury Cougar

This grade "B" support will be rust free but will need minor straightening on the lower mounting tab. Once worked on the damage should not be noticeable. Customer feedback; Hey Don, I've been ordering parts for my '67 over the last few months from your company. I just want to let you know I would recommend your company to anyone. You have been extremely helpful in every aspect. I think your site is great and easy to use. I especially liked how you call me with questions and answers...

Used  Grade A driver side support / grille center for the 1969 Mercury Cougar

Used Driver Side Grade "A" Center Grille Support for the 1970 Mercury Cougar

Used Driver Side Grade "B" Center Grille Support for the 1970 Mercury Cougar

Used Passenger Side Grade "A" Center Grille Support for the 1970 Mercury Cougar

Used Passenger Side Grade "B" Center Grille Support for the 1970 Mercury Cougar

This body part is painted body color and mounts vertically on either side of the center grille. Grade "A" part with no rust or dents, ready to paint and install. This is a 3 piece set, which includes: D1WY-8283-A and D1WY-13B116-B. Driver side filler between grille and headlight assembly. Does not include chrome trim or hood rubber bumper on top.

This body part is painted body color and mounts vertically on either side of the center grille. Grade "A" part with no rust or dents, ready to paint and install. This is a 3 piece set, which includes: D3WY-8283-A and D3WY-13B116-B. Driver side filler between grille and headlight assembly. Does not include chrome trim or hood rubber bumper on top.

This body part is painted body color and mounts vertically on either side of the center grille. Grade "A" part with no rust or dents, ready to paint and install. This is a 3 piece set, which includes: D1WY-8282-A and D1WY-13B116-A. Passenger side filler between grille and headlight assembly. Does not include chrome trim or hood rubber bumper on top.

This body part is painted body color and mounts vertically on either side of the center grille. Grade "A" part with no rust or dents, ready to paint and install. This is a 2 piece set, which includes: D3WY-8282-A and D3WY-13B116-A. Passenger side filler between grille and headlight assembly. Does not include chrome trim or hood rubber bumper on top.

Support brace between the cowl top and the brake pedal support bracket. Fits 1969-70 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Ford part number C9ZB-6501554.

Support brace between the cowl and the top of the brake pedal support bracket. Fits 1969 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Overall width is right at 5 inches on the 1969, smaller than the 1970 version. Ford part number C9ZB-65015A18-A.

Support brace between the cowl and the top of the brake pedal support bracket. Fits 1970 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Overall width is right at 5-1/2 inches on the 1970, larger than the 1969 version. Ford part number D0ZB-65015A18-A.

This tubular support gives rigidity to your hood extension which houses your center grille. These are hard to find with no bends or cracks due to the fact that the 1970 hood protrudes in the center.1 required per car.

Used strap or support bracket for the foam air conditioning vent tube going to the driver side A/C vent. The electrical assembly manual indicates that this strap bracket behind the dash on the driver side. Our findings from the wrecking yard show that 1967 is typically rubber coated, 1968 is bare steel. Please specify is you have a preference. The rubber coated ones will show some deterioration, plan on re-dipping or use as-is. Not exactly the same as the support for the passenger side.Ford...

C9ZZ-6501508-B This is the correct hanger for a 1969 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number C9ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes and an automatic transmission. This unit is not for cars produced after 6/25/1972. Ford part # D1ZZ-6501508-C.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with an automatic transmission and manual drum brakes. This unit is for cars produced after 6-25-1972. Ford part # D3ZZ-6501508-C.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with a manual transmission and manual drum brakes. Not to be used in cars produced before 6/25/1972. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D3ZZ-6501508-A.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and in unused condition. Ford part # C9ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to...

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D0ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to the...

Reproduction brake pedal hanger for manual brakes. Can be modified to work for power brakes.

This used brake pedal support bracket is the correct hanger for a 1967-68 Mercury Cougar or Ford Mustang with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint, unused condition. Ford part # C7ZZ-6501508-C. *NOTE* Manual brake supports are different. Manual brake supports have four threaded...

This used brake pedal support bracket or brake pedal hanger is for the Mercury Cougar or Ford Mustang equipped with power disc or drum brakes. We have carefully shown the mounting position of the pedal so you can drill your existing manual brake pedal hanger when converting from manual to power brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means...

D1ZZ-6501508-D This is the correct hanger for a 1971 Mercury Cougar or Ford Mustang and 1972 cars up until 6-25-1972, with power disc front brakes, and with automatic transmissions. Ford master part number D1ZZ-6501508-D for power disc front brakes.

D3ZZ-6501508-D This is the correct hanger for a after 6-25-1972 Mercury Cougar or Ford Mustang and 1973 cars, with power disc front brakes, and with automatic transmissions. Ford master part number D3ZZ-6501508-D for power disc front brakes.

D0ZZ-6501508-B This is the correct hanger for a 1970 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number D0ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...

Reproduction brake pedal hanger also known as the brake pedal support for Mercury Cougar and Ford Mustang.

Reproduction brake pedal hanger also known as brake pedal support for Mercury Cougar and Ford Mustang.

Used front support bracket for the air conditioning compressor assembly. Starting in 1971, Ford eliminated the idler pulley and used this bracket in it's place. Replaces part # D1AZ-2888-B.

Support bracket for attaching headlight assembly to the radiator core support. Right and left are the same, two needed per car. Fits 1971-73 Mercury Cougar.Ford part number D1WY-13B065-A.

Used upper support bracket for the hood latch on any 1969 Mercury Cougar. Ford part number C9WY-16707-A.

Used upper support bracket for the hood latch on any 1970 Mercury Cougar. This 1970 part will work on a 1969. The only difference is the top corner is clipped at an angle on the 1970.Ford part number D0WY-16707-A.

This support bracket mounts to the lowest portion of the quarter window cavity. This bracket is installed before the lower guide bracket. Fits all 1971-73 Mercury Cougar models and 1971-73 Ford Mustang models including fastback or sport roof models. The exploded view of the quarter window parts can be found in the Osborn Body Assembly Manual for 1971-72. One for each quarter window