1970 Mercury Cougar

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Fits all 1969-70 Mercury Cougar and Ford Mustang. Sold as a pair and are not side specific. 

Rear Wheel Cylinder (29/32", Right Hand) Fits either Right Hand or Left Hand. Sold individually, 2 required per car. Replaces Ford Part #: C3OZ-2262-B and D2ZZ-2262-B.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits in a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part #: C3OZ-2062-B, D2ZZ-2062-A, & D3ZZ-2062-A.

Reproduction passenger side (right hand) wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits into a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part # C3OZ-2061-B, D2ZZ-2061-A, & D3ZZ-2061-A.

Reproduction drum brake backing plate hole cover plug. Replaces Ford Part # 8A-2092.

Used driver side (left hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar or Ford Mustang, and Fairlane / Torino equipped with 351 or larger V8 engines. Ford part # C9OZ-2013-B. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

Used passenger side (right hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane / Torino equipped with the 351cid or larger V8 engine.Ford part # C9OZ-2012-A. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

Quality rebuilt LH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included. Check out our caliper tips and tricks video below: ...

Quality rebuilt RH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included.Check out our caliper tips and tricks video below: ...

Replaces Ford Part # 382713-S Sold individuallyCheck out our caliper tips and tricks video below: ...

Sold as a Pair. Ford Part #: C8AZ-2B296-ACheck out our caliper tips and tricks video below: ...

part# 384114-S100 Sold individually Check out our caliper tips and tricks video below: ...

Used drum brake distribution block for Mercury Cougar and Ford Mustang equipped with front drum brakes. This unit mounts to the driver side fender apron with two nuts. Bare block without brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # D0OZ-2B257-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

These new brake drums are perfect replacements for tired and thin originals on you Cat or Pony. Fits cars with either the 2 1/4 inch or 2 1/2 Inch shoes. Front drums do not include studs or a hub. Drums Provide Consistent Quality & Reduced Noise.; Drums Are Vehicle Specific & Meet Federal Safety Standards.; Castings Meet Sae J431/g3000 Specifications For Proper Tensile Strength.; Machined To Control Perpendicularity & Run-Out For Optimal Performance & Brake Life.Also fits V8...

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 71.6 mm Center Bore Diameter : 61.8 mm Maximum Discard Diameter : 256.3 mm O.D. : 296.3 mm Replaces Ford Part #:C2OZ-1126-B

Flexible high pressure replacement brake hose for front drum brakes that fits both passenger (right hand) and driver (left hand) sides of Mercury Cougar or Ford Mustang. Sold individually, please remember to order two if a pair is needed.Replaces Ford part # C7ZZ-2078-A.

Flexible high pressure replacement brake hose for the front driver (left hand) side of Mercury Cougars or Ford Mustangs equipped with disc brakes.Replaces Ford part # C8ZZ-2078-B.

Flexible high pressure replacement brake hose for the front passenger (right hand) side of Mercury Cougars or Ford Mustangs equipped with disc brakes.Replaces Ford part # C8ZZ-2078-A.

FINALLY! The correct rear flex hose for the 1970-73 Mercury Cougar. The Mustang rear steel line fitting is .323" whereas the Cougar fitting is .395". If you have purchased a reproduction front to rear steel brake line, you will want to make sure whether you have the Mustang .323" or the Cougar .395" rear fitting as some vendors sell a "Cougar" bent steel line with a Mustang rear fitting.  If you have the .323" fitting, you will need to purchase the Mustang flex hose (D1ZZ-2282-A, click...

This intermediate OE-style steel line attaches to the transmission tunnel and connects the brass distribution block in the front to the flexible brake hose in the rear of the car. Application does not change if the front is drum or disc in the front, all Cougars 1967-1973 came with drum in the back.  Not for Mustang as the Mustang had a shorter wheel base than Cougar.  Line is too long to economically be shipped without bending it over, carefully straighten it out prior to...

Reproduction OE steel power disc brake line kit for the Mercury Cougar. This item is bent and dropshipped from the supplier when it is ordered and is available in both OE steel and stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

Reproduction stainless steel power disc brake line kit for the Mercury Cougar. This item is bent and dropshipped from the supplier when it is ordered and is available in both OE steel and stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

Reproduction stainless steel standard drum brake line kit for the Mercury Cougar. This item is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.  NOW AVAILABLE WITH THE CORRECT REAR BRAKE LINE FITTING FOR THE COUGAR!    The Mustang fitting is .323" whereas...

Reproduction steel lines for the drum brake master cylinder on 1970 Mercury Cougar and Ford Mustang. Connects the master cylinder to the brake distribution block. 

Two-piece OE-Style steel Rear Axle Brake Line Set 67 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. 1970 differs from 69...

Two-piece Stainless Rear Axle Brake Line Set 70 Mercury Cougar and Ford Mustang with 9" Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any possible leaks. ...

Replaces Ford Part # C8AZ-2069-A Sold individually

Replacement brake pedal pad trim for the Mercury Cougar or Ford Mustang equipped with a manual transmission. Replaces Ford part # D1ZZ-2A487-B.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

All new premium disc brake pads are supplied to us by brand name manufacturers. Set of 4 pads. Low dustProtective underlayerRubber/steel/rubber layered shimScorched

Used short style brake pedal for the Mercury Cougar and Ford Mustang equipped with an automatic transmission and manual drum brakes on all four wheels. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare. Ford part # C9ZZ-2455-C.

Longer arm than drum brake pedals. Works only with 1970 power brake booster rod. Pedal shipped bare, picture may show hardware and pedal pad with trim. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you...

For use with a clutch pedal. Longer arm than drum brake pedals. Comes with all mounting hardware. Pedal shipped bare without pedal pad with trim.

Reproduction drum brake pedal pad for the Mercury Cougar or Ford Mustang equipped with an automatic transmission. The 1967 version of this piece is narrower than this 1968-73 piece.Replaces Ford part # C6OZ-2457-A.

Reproduction brake pedal pad for the Mercury Cougar and Ford Mustang equipped with a manual transmission and drum brakes. This unit is a good fit and is a quality part. Replaces Ford part # C5ZZ-2457-G.

Excellent quality replacements. Includes hub, studs, and bearing races. Single piece design. 2" spacing from hub to rotor face