1970 Mercury Cougar

Used driver (left hand) side brake shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Left side screws are identified by an "L" on the end of the screw under the socket and a single groove machined into the pivot nut. Original Ford part number for the passenger (right hand) side is...

Used passenger (right hand) side brakes shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Right side screws are identified by an "R" on the end of the screw under the socket and a two grooves machined into the pivot nut. Original Ford part number for RH or passenger side is C2OZ-2041-A,...

Reproduction 10 x 2-1/4 inch premium semi-metallic front drum brake shoes for Mercury Cougar or Ford Mustang with front 10 inch drum brakes.  Double check that shoe width measurement on your car, there were some cars sold with 2-1/2 inch wide shoes.

New front10 X 2-1/2 inch brake shoes for the Mercury Cougar or Ford Mustang. These will fit the rears of some Ford vehicles, but not a Cougar or Mustang without modification.Typically this size of brake shoes is only found on the front of a Cougar or Mustang. You would have to have 2-1/2 rear backing plates in order to use these shoes on the rear of your car.

Premium grade of rear brake shoes with semi metallic brake linings. 10 inch diameter drum brakes. Please measure your brake shoes, there are also 1-3/4 inch wide shoes too.

Driver side disc brake spindle for 1970 Mercury Cougar and Ford Mustang. Ford part number D0OZ-3106-B left hand or drivers side disc brake spindle. We have to price our disc brake spindles so as not to deplete our complete used conversion kits. Ford casting number D0ZA-3108-C.

Passenger side disc brake spindle for 1970 Mercury Cougar and Ford Mustang. Ford part number D0OZ-3105-B right hand or passenger side disc brake spindle. Ford part number D0OZ-3106-B left hand or drivers side disc brake spindle.We have to price our disc brake spindles so as not to deplete our complete used conversion kits. Ford casting number D0ZA-3107-C.

Pair of exact copy reproduction brake spindles for 1970 - 1973 Mercury Cougar and Ford Mustang. The originals used different Ford part numbers for the 1970 spindles and the 1971 - 1973 spidles, but there was really no difference. These reproductions will not have Ford part numbers.

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The benefit of using this foam float, is that sometimes the hollow brass float will leak, causing a bad reading. This foam version of the float is fuel resistant and will never leak. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The problem with these brass floats, is that after year of being in contact with fuel, they will begin to corrode and disintegrate. We suggest going with the new foam floats. They are fuel resistant and will last longer. Find it here. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

Core driver side (left hand) high back bucket seat for the Mercury Cougar. In most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Perfect for a 1969 Eliminator clone or to make your 1967-68 safer and more comfortable. If you are going to use these high backs in your 1967-69 Cougar, your existing seat tracks...

Core driver side (left hand) and passenger side (right hand) pair of high back bucket seats for the Mercury Cougar. In most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Perfect for a 1969 Eliminator clone or to make your 1967-68 safer and more comfortable. If you are going to use these high backs in your...

Core passenger side (right hand) high back bucket seat for the Mercury Cougar. In most cases the foam will be less than perfect and will need to be recovered. They will be solid core frames taken from a Western parts car and, from our experience, are MUCH better quality than the Chinese made reproductions on the market. Perfect for a 1969 Eliminator clone or to make your 1967-68 safer and more comfortable. If you are going to use these high backs in your 1967-69 Cougar, your existing seat...

Fits RH or LH standard interior, sold individually, two required per car. Has correct grain texture and injection molded exactly like originals. Includes metal clip retainers pre-installed as well as the clips themselves. Available in black only, use any solvent based paint to match the color of your interior. These were used on the 69 - 70 (and some 68) Mustangs but only used in 1970 for the standard model Cougar. Replaces Ford part #: C9ZZ-6560762. ...

Grade A XR7 used bucket seat vinyl trim panel. Available in 1969 1970 interior colors. Please specify in the notes your desired color. Grade A will not have cuts or tears, there may be slight impressions in the vinyl or a warped backer board. Driver and passenger side are the same, sold individually. Typically these would have had a basic Ford part number of 60762. XR7 panels have the map pockets on the back. The elastic may be stretched on these.  We also have B grade used panels...

Grade B XR7 used bucket seat vinyl trim panel. Available in 1969 1970 interior colors. Please specify in the notes your desired color. Grade B will have cuts or tears, there may be slight impressions in the vinyl or a warped backer board. Driver and passenger side are the same, sold individually. Typically these would have had a basic Ford part number of 60762. XR7 panels have the map pockets on the back. The elastic may be stretched on these.  We also have A grade used panels too,...

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...

Reproduction 1156 Back Up Light Bulb for the 1969 - 1973 Mercury Cougar

Brand new 1157 (dual-filament) exterior stop lamp / turn signal light bulb for the Mercury Cougar or any vehicle equipped with 1157 bulbs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. For even brighter...

The 67 -73 Cougar uses the 1157A (Amber) bulb for the turn signals.  This bulb will also fit other applications that require an 1157A or 1157NA bulb. Replaces bulb #: 1157A or 1157NA

Replacement lamp for the speedometer, heater controls, ashtray, automatic shift indicator, low fuel, seat belt reminder, or emergency flasher warning lights on the visual check panel.

This bulb fits several applications including the door panel courtesy lights in the 1967 - 1968.

New 1891 bulb for the 1967-68 XR7 overhead console. This bulb will also fit the 67 - 68 rear console light. You can find the LED version of this bulb here.

New 1895 bulb for the instrument clusters. *Note - The table and the owners manuals are wrong for the Visual Check Panel bulbs, Ford literature calls out a 1895 bulb, when in fact the correct bulb is 1891.

Reproduction 194 light bulb that can be used for your gauges, high beam indicator, clock, or turn signal indicators for the Mercury Cougar.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Reproduction 257 Door Ajar / Park Lamp Light Bulb for the1969 and 1970 Mercury Cougar

Reproduction 631 Glove / Luggage Compartment / Under Dash Courtesy / Trunk Light Bulb for the 1967 - 1973 Mercury Cougar

Rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors.Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B Check out our...

Used rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors. Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B  Check out...

One used anti rattle spacers / guards that go between the fender and the cowl on each side. The majority of 1969 Cougars and Mustangs used a black foam block glued to the cowl but in late 1969 and all of 1970 these wedge shaped rubber parts were used. Replaces Ford part number C9ZZ-16758-A.

Pair of anti rattle spacers / guards that go between the fender and the cowl on each side. The majority of 1969 Cougars and Mustangs used a black foam block glued to the cowl but in late 1969 and all of 1970 these wedge shaped rubber parts were used. Replaces Ford part number C9ZZ-16758-A.

Reproduction cowl cover to hood rubber bumpers for the Mercury Cougar or Ford Mustang. These little units attach to the front of the cowl cover for the back corners of the hood to sit on. These will also work for the 1967-68 Mercury Cougar or Ford Mustang fuel filler door bumpers if you are missing them. Sold as a pair and comes with the attaching screws. *NOTE* These are not an exact replacement, rather a part from another year and application that has been found to be an adequate...

Good core 1970 front bumper in need of re-chroming. You will need to purchase this if you are purchasing our re-chroming service and do not have a good core.

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Mounts to the bottom lip of the coil spring cover, two required per car, sold individually. Replaces Ford Part #: C9OZ-3020-B.

Mounts to the bottom lip of the coil spring cover, two required per car, sold individually. Ford Part #: C9OZ-3020-B.

Sold as a pair. Two required per car.Replaces Ford Part #: 380239.

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1969 or early 1970 Mercury Cougar and Ford Mustang with glue-in door glass. This bumper will not work if your door glass is the 1970 bolt-in glass. We also sell the version for the 67-68 and late 1970 bolt in glass.Ford part # C9ZZ-6521762-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for...

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1969-1970 Mercury Cougar and Ford Mustang glued-in door glass.  Note that this bumper is substantially shorter than the 70  bolt-in door glass version.   See D0ZZ-6521762-A for the 1970 bolt-in door glass version.  If you are swapping out a door on a 69 or a 70 don't forget that the door glass is different between the years and, if you have to swap out the glass, you will...

Exact fit for the front license plate brackets, will also fit the rears, but not concours.

Sold individually, two required per car. Replaces Ford part # C3DZ-4730.

This option includes paying a core charge. By choosing this option, the re-chromed bumper you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Mounts over rear axle ends into the body/frame, two required per car, this is the more pointed Christmas tree shaped version.Ford part # C6AZ-4730

This option includes paying a core charge. By choosing this option, the re-chromed bumper you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming...

Rubber bumper used on 69-70 taillight housings to cushion the closing of the fuel door, sold individually, two required per car. Replaces Ford Part #: 16758.

Here is a time and money saving package deal for the person restoring their 1969 Cougar. This package includes: Right and Left Hood lip mouldings Fender extension mouldings (eyebrows) Deck / Trunk lid moulding Six Piece Convertible Windshield Trim Kit Front and rear Award Winning Bumpers Keep in mind we will often give extra core value trade in for items we may be low on. Please call before sending extra parts for trade value. All parts are show quality. The bumpers are triple plated chrome,...

Here is a time and money saving package deal for the person restoring their 1970 Cougar. This package includes: Hood lip mouldings Fender extension mouldings Deck lid moulding Drip rail mouldings (specify w/ or without vinyl top) Nine piece front and rear window trim Front and rear Award Winning Bumpers Keep in mind we will often give extra core value trade in for items we may be low on. Please call before sending extra parts for trade value. All parts are show quality. The bumpers are triple...