1970 Mercury Cougar

Quick disconnect that installs between the sight glass hose and the sight glass to A/C dryer hose. This unit also includes 2 O-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316)Quick Connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252).

Slat or pivot bracket for attaching the #4 rear most bow on a 1969-70 convertible top. Sold individually, one for each side needed for installation. Bushing is normally broken or missing, plan on sourcing or making a replacement bushing for the pivot. Ford part number C9ZZ-7650340-A.

Reproduction power steering control valve sleeve / socket for the Mercury Cougar or Ford Mustang.

New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3. 

New phosphate dipped slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". Sold individually, you will need 2. 

Reproduction Small Block Engine I.D. Bolt for the  1967 - 1973 Mercury Cougar / 1967 - 1973 Ford MustangSold individually 

Thermactor smog hose installation clamps. Fits all Ford and Mercury 1968 S code 390-4V or W code 427-4V engines sold in the US. Additionally fits 1968-70 428 Cobra Jet and Super Cobra Jet engines. Set of clamps, several bolts and spacer as shown. Include bolts for pump pulley, top bolt on pump for adjusting bracket, and pivot bolt and spacer for pump.

Reproduction hardware kit for installing the smog pump on cars with 390 / 427 / 428CJ engines from 1968-70. Including Cougar, Mustang, Torino, Ranchero, Cyclone, etc. Includes spacer, pivot bolt and washer, adjusting bracket bolts.

Set of thermactor smog tubes on any 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original 390 or 428CJ cylinder heads drilled for air injection smog system from factory. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the ferrules / nuts and other hardware.

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

Application is for all 1970 351 Cleveland engines, both 2 barrel and 4 barrel. This air cleaner snorkel is different from past years in that the opening is necked down and has a flared flange. It also has a small opening on the bottom for a metal "S" tube. Ford part number D0OZ-9A626-D. Click on images to enlarge. ...

Applications all 1969 351 engines, both 351-2V and 351-4V, and 1970 351W-2V engines after 2/2/1970. That is correct, after Feb 1970 the H-code Windsor engined 351's used a 1969 style air cleaner snorkel.The C9OZ-9A626-B snorkel looks the same, but is a bit longer than the 1968 C8AZ-D snorkel. Probably due to the taller deck height of the 351 over the 302 engine, and or the heat shield design. Please note: Wax stat is not tested, nor can we test them, sold as- is. Click on images to enlarge. ...

Application is for the beginning of the 1970 model year and only for H-code 351W-2V. Windsor engines only, from inception until 2/2/1970. Ford part number D0OZ-9A626-B.

Quality recreation made from original parts. Decent reproduction, slightly different than the original Ford version. The noticeable difference is the lack of square notch in the slop joint. Ford part of C8OZ-9A626-C. This snorkel comes to you in primer.

For all 1968 through 1970 R and Q code 428CJ and SCJ air cleaners. Snorkel has the opposite jog than 390GT snorkels. This one jogs towards the rear of the engine. Originally this snorkel should have had an ink stamp of C8OF-9A626-A or -B. Ford MPC number C8OZ-9A626-C.

Although these are considered reproductions, they are actually put together from multiple parts of original excellent condition used snorkels. And, since there are multiple colors of Ford Blue, the supplier is leaving them as unpainted.Application would only be for 1970 Boss 302 Eliminators and Boss2 Mustangs. Ford part number D0ZZ-9A626-B.

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Used under dash wiring harness repair plug and pigtail to the ignition switch light socket for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Light socket harness for the headlight reminder option. Works in conjunction with dash light and buzzer. 1970 XR7 and Eliminator option, not for standard, non- Eliminator models. Ford part numbers D0WY-13B155-A and wire cast number D0WB-13B155-A.

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

This is the same sound deadener kit that everyone else is offering, but if what you are looking for is a kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least...

If what you are looking for is a sound deadener kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least this listing will give you an honest idea of what you are...

5/16" thick sound deadening and heat reflecting material, comes in a 4' X 6' sheet that can be cut to fit. This insulation consists of two layers of polyethylene bubble film sandwiched between two layers of aluminum foil. Temperature range rated -60 deg. F. to 180 deg. F. Combining this with the tar-based sound deadener underlayment will result in similar sound deadening as the OEM sound deadener.Below is listed how many rolls you will need to underlay the sections of a Cougar:  Area...

This sound deadener is comprised of one layer of tar sound deadener and a layer of Jute. Here is a shot of the original sound deadener pulled (slightly) apart to expose the en-capsuled insulation.  This new OEM style sound deadener is very similar, but is lacking the extra layer of tar on the bottom.  This can be overcome by adding the tar only kit to this kit.  This combination will come by far the closest to OEM than any other kit available! ...

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Replaces Ford Part # D0ZA-A

Reproduction Space Save Tire Instructions Decal for the 1968 - 1973 Mercury Cougar / Ford Mustang

Reproduction Space Saver Spare Recall Postcard for the 1968 - 1971 Mercury Cougar / Ford Mustang

Aluminum spacer used on 289/302/351 engines for mounting the alternator. Length is 1-5/8 inches long, mounts between the alternator and the cylinder head.

Alternator spacer bracket for all 351 engines. 1970-73 Mercury Cougar and Ford Mustang among others such as Torino, Cyclone, Galaxie, LTD, etc. Aluminum material, 2-1/4 inches long, with a 7/16" hole. Sometimes solid and sometimes open along the side. Ford part number D0OZ-10A370-A.

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. New manufactured.

B8AZ-6359-A Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. Used spacer, will show a little wear from the outside seal. 

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Reproduction 384542-S2 Power steering pump adjusting spacer for use without air conditioning. For all 1970 and later Mercury Cougar or Ford Mustang with 302 or 351W engines. Spacer dimensions: 7/16" I.D. and 3/4" thick.*Note - 351C engines use a 1/2 inch spacer.

Reproduction  Lower Windshield Moulding Center Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Used spacer for the lower windshield moulding

Reproduction  Lower Windshield Moulding Fender Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.