1970 Mercury Cougar

Left is the same as right, one year only emblem at the center top of the door panel. Usually will show a small amount of pitting. Casting number as seen on the back reads D0WB-6520802.

Decent reproduction of the 69-70 Cougar fender extension COUGAR script. This emblem was used for 2 years only and was located on the driver side front fender extension (fender cap). The originals came with speed nuts but these have push on clips from the back which means they are easier to install as no tools are needed. If one looks very close you will see minor differences compared to original examples. If you want to trade in your dull, pit free emblem for store credit we will give $20 for...

Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside: C9WB-16098-B Ford number C9WB-16098-A. Note that the 1970 version stamped D0WA-16098-A is slightly different, most noticeable on the letter "C".

Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside:  Ford number D0WB-16098-A. Note that the 1970 version is stamped D0WA-16098-A.

These fuel door Mercury crest emblems have been lovingly restored by a long time Cougar enthusiast. They have been carefully repainted the correct colors and will really liven up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. The engineering number on the back is C9WB-65405A92. To remove your emblem we suggest grinding down the studs on the backside. To install the restored emblem you will have to use epoxy glue. Keep in mind you...

Reproduction center grille emblem background. This decal is only made with the "7", so you will need to remove the "X" and "R" from your existing decal and adhere them to this new one. You can clean those letters up with some extra fine polishing steel wool. The standard grill emblem with a walking cat uses the same stud configuration as XR7 so you can exchange emblems from one to another. ...

Used Grade A 3 1/2" XR7 center cap emblem was used on the Mercury Cougar XR7 hubcap / wheel cover. 

Used Grade B 3 1/2" XR7 center cap emblem was used on the Mercury Cougar XR7 hubcap / wheel cover. 

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

Correct anodized aluminum reproduction emblem for 1969-70 quarter panels. These high quality emblems have the black paint applied to the sides just as the originals did. If you want an emblem that better matches your front Cougar script you might want to consider these chrome emblems. You can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem. Measurements are from the rear and lower body lines. *NOTE* This item includes the three...

Used COUGAR Script Quarter Panel Emblem for the 1969 and 1970 Mercury Cougar

This "Stick On" Cougar rear deck emblem was only used on models without the XR7 package. They are often missing as once the factory double sided tape dries out they are often lost forever. We also have a few very nice used examples in stock.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line...

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Reproduction silver walking cat emblem / insert for the 70 Eliminator T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 69 - 70 Eliminator, this handle will fit on any 67 - 73 Cougar with the automatic transmission.

Excellent reproduction of the little 1 1/8" wide plastic emblem found on every 1970 - 1974 three spoke steering wheel pad. This emblem can also work on the 1969 - 1973 two spoke steering wheel pad but it is not an exact fit as the two spoke wheel emblem is only 1 1/32" wide. Keep in mind we made these EXACTLY as original so they are very fragile. If you happen to break the emblem anytime within three years of purchasing it we will sell you a replacement for half price when you submit the...

This small sized Cougar emblem (1 3/8" long) was used on 1969 - 1973 Cougars without AC. It was affixed to a block off plate in the very venter of the dash by two peened over die cast studs. It will glue back in place nicely and many Cougar fans have found fun "custom" applications for this attractive piece. This emblem will not be pitted or scratched in any way.

Since our restored emblems look so good we have a hard time selling NOS these days which works out just fine as we only seem to be able to obtain 1 of these every few years. Keep in mind your used cores have trade in value against this NOS part. Casting number seen on back side for the assembly is C9WB-65517A56-A and black plastic is C9WB-65517C00-A, Casting number on chrome is C9WB-65517A20-A

This vinyl piece glues to the center of your block off plated on Cougars not equipped with AC. These often times have shrunk slightly over time. We cannot guarantee to always have all the colors in stock. Call for color availability or put desired color into the comments section of your order.

This grille background piece requires you remove your Cougar emblem before installing. To remove the cat emblem you will need to grind from the backside and epoxy the emblem back in place after-wards. Vast improvement over your current faded, dinged part. Not for use on the xr7. ...

Reproduction emergency / parking brake cable return spring that goes underneath the car for the Mercury Cougar or Ford Mustang.

Reproduction emergency / parking brake assembly for the Mercury Cougar that is sold as a complete assembly. These units do look way better than our used crusty originals, but they will never hold up as well as original FoMoCo!Replaces Ford part # D0ZZ-2780-A

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for LH or DRIVERS side original part Ford number is C9ZZ-2A638-A.

Used parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for LH or driver side is C9ZZ-2A638-A. This unit is from a solid Western parts car, so you won't be getting one of those rusty East Coast units! Ford part # C9ZZ-2A638-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for RH or passenger side original part Ford number is C9ZZ-2A637-A.

C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.

Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A

Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.

New Old Stock emergency flasher for the 1970 Mercury Cougar Ford Part number D0WB-13350-B

New emergency flasher can for all 1969-73 Mercury Cougars. Not to be confused with the turn signal flasher canister, those are rated differently. 

Used emergency flasher for the 1970 Mercury Cougar Ford Part number D0WB-13350-B

There are multiple emissions decals available for the 351 Cleveland 2 barrel with an automatic transmission in 1970 for the Mercury Cougar or Ford Mustang. This sticker is printed with part number D0AE-9G485-S.

There are multiple emissions decals available for the 351 Cleveland 2 barrel with an automatic or manual transmission in 1970 for the Mercury Cougar and Ford Mustang.  This sticker is printed with part number D0AE-9C485-A.

Emission Decal for the 351 Cleveland 2 Barrel with an automatic or manual transmission in the 1970 Mercury Cougar or Ford Mustang. Printed with part number D0AE-9C485-AH.

Emission decal for the 351 Cleveland 4 barrel with an automatic transmission in the 1970 Mercury Cougar or 1970 Ford Mustang manufactured before January 1, 1970.  Printed with part number D0AE-9C485-F.

Emissions decal for the 351 Cleveland 4 barrel with automatic or manual transmission on the 1970 Mercury Cougar and Ford Mustang manufactured after January 1, 1970. Printed with part number D0AE-9C485-AG.

Emission Decal for the 428 4 barrel with an automatic or manual transmission in the 1970 Mercury Cougar and Ford Mustang. Printed with part number D0OE-9C485-J.

Exhaust Emission Control decal for the BOSS 302 with a manual transmission in the 1970 Mercury Cougar and Ford Mustang manufactured after January 1, 1970. Printed with part number D0ZE-9C485-F.

Exhaust Emission Control decal for the BOSS 302 with a manual transmission in the 1970 Mercury Cougar and Ford Mustang manufactured before January 1, 1970. Printed with part number D0ZE-9C485-B.

This two part black box is what encapsulates your sequential unit for all years 1969-1973. This of course will work with our reproduction sequential unit as well. This box was designed hang from a hook that is welded to the trunk floor just behind the driver side wheel well. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Angled bracket for mounting the steel dash panel to the cowl. Two brackets per car, sold individually. These are the end mounting brackets for all 1969-70 Mercury Cougar and Ford Mustangs with or with air condtioning. Ford part number C9ZB-5404366.

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

These Big Block motor mounts bolt to your engine block on the top side and to the motor mount (insulator) on the bottom side. These are very correct looking and fitting reproductions, much better than the $95 version you will find in most catalogs. Fits 1967-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines, will fit passenger side of 427 side oiler engine, driver side will work with modification. Original Ford part numbers C7ZZ-6046-A R.H., C7ZZ-6046-B L.H. 427 number for the left...

Engine Code Decal for the 302 with automatic transmission and air conditioning on the 1970 Ford Mustang. Printed with L 6° K272AG.

Engine Code Decal for the 302 with a automatic transmission on the 1970 Ford Mustang.  Printed with L 6° K280A.

Engine Code Decal for the 302 with a manual transmission on the 1970 Ford Mustang. Printed with L 6° K279A.

Engine code decal for the 351 Cleveland with a 2 barrel carborator on the 1970 Mercury Cougar and Ford Mustang manufactured after January 1, 1070. Printed with L 10° K834 K.

Engine Code Decal for the BOSS 302 with a Drag Pac on the 1970 Mercury Cougar and 1970 Ford Mustang. Printed with L 16° 300S.