1970 Mercury Cougar

Replaces Ford part #C1SZ-13783. Replaces burnt, cracked or missing original lenses located above the rear package tray.  Two required per car, sold individually.

This is the chromed correct die cast construction for your 1969 Cougar, 1970-73 used plastic but these will fit fine and look better than the plastic units. Great Quality. Sold individually, two required per car. Part of the XR7 package. Available on other hardtop models, part of the Courtesy Light group option. Option included, engine compartment light, trunk light, map light and these rear quarter panel lights for the back seat. Replaces Ford Part #: C4SZ-13776-B.*Trivia Dearborn built...

These lights feature beautiful chrome bezels and bright white lenses. Mounting hardware, bulbs and sockets with pigtails are included. These were used on the XR7 and all Cougars equipped with Decor level interiors in 1969 and 1970. These are AWESOME reproductions worthy of the most exacting of restorations. You will be VERY happy with these lights. Sold as a pair. Replaces Ford Part #: C9WY-13776-A & C9WY-13777-AThese use a 212 bulb.Click on images to enlarge. ...

C9WY-13777-A-AGRADE Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Hardest side to find in primo condition most get dinged up from errant seatbelts. These are available in reproduction. Nice Quality!These use a 212 bulb. ...

C9WY-13777-A Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses. These are available in reproduction. Nice Quality!These use a 212 bulb.

New Old Stock Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. These are available in reproduction. Nice Quality!Ford part number C9WY-13777-A. These use a 212 bulb.

C9WY-13776-A-AGRADE Right side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. These are available in reproduction. Nice Quality!These use a 212 bulb.

C9WY-13776-A Right side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses. These are available in reproduction. Nice Quality!These use a 212 bulb.

These courtesy lights are located on the very outer right and left under the dash. Sold individually, this is the driver side version. We inspect for damage, clean contacts, and test. These are 1970 model only courtesy lights with unique lamp. Right and left are basically the same, one has a bend as shown. Plus they have the part number stamped on them.Replaces Ford part number D0ZB-13K705-C.Fits: 1970 Mercury Cougar 1970 Ford Mustang ...

These courtesy lights are located on the very outer right and left under the dash. Sold individually, this is the passenger side version. We inspect for damage, clean contacts, and test. These are 1970 model only courtesy lights with unique lamp. Right and left are basically the same, the driver side version has a bend in the metal mounting bracket.  Plus they have the part number stamped on them.Replaces Ford part number D0ZB-13707-C.Fits: 1970 Mercury Cougar 1970 Ford Mustang ...

D0AB-13776-A 1970 Right and left lights are the same. They are located on the "C" pillar just above the rear package tray. These plastic housings never really had brilliant shiny chroming. Marked D0AB-13776-A on the wiring, fully interchanges with the 1969 light. Same plug, same diameter opening in the sail panels. Ford master part number D0AZ-13776-A. Grade B will have imperfections and or scratches in the plastic chrome. *Restoration Tip* There are paint manufacturers that offer shiny chrome...

Reproduction LED version of the under dash courtesy light located on the very outer right and left under the dash. Although the originals had very slight differences between left and right, this reproduction is good for both sides.  Includes LED bulb. Sold individually, 2 per car required. Replaces Ford part numbers D0ZB-13707-C and  D0ZB-13K705-C

The Eliminator uses the XR7 harness but not the XR7 rocker switches in the center of the dash. This bypass plug completes the circuit left open when no XR7 switches are plugged into the harness.Ford part # C9WB-13B676-A

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

Reproduction ashtray cover assembly for the center console found in the Mercury Cougar or Ford Mustang. Does not include ashtray receptacle, which is sold separately. Replaces Ford part # C9ZZ-6504814

Used ashtray cover assembly for the center console found in the Mercury Cougar or Ford Mustang. Does not include ashtray receptacle, which is sold separately.. NOTE: When ordering, mention what color you're looking for in the order comments and we will do our best to accommodate.

Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.

Used door window stop, cover plate, for any 1969-70 Mercury Cougar and Ford Mustang. These were originally painted body color, and were laid on either inside the front cowl or the package tray for painting. The one for the doors is roughly 25/32" x 3-3/8 inches long, the holes are 5/16, and the spacing is 1-25/32 on center to match the stop. Replaces Ford part number C9ZZ-65234A30-A.

Used quarter window stop, cover plate, for any 1969-70 Mercury Cougar and Ford Mustang. These were originally painted body color, and were laid on either inside the front cowl or the package tray for painting. The one for the quarter is roughly1" x 2-7/16 inches long, the holes are 5/16, and the spacing is 31/32" on center to match the stop. Replaces Ford part number C9ZZ-6530068-A.

Tilt steering column cover plate for turn signal lever. Two versions, two different sizes of openings for the turn signal wand. Original used Ford part, plan on painting to match your steering column. Fits all 1970-71 Mercury Cougar, 1970 Ford Mustang, and other Ford/Mercury cars with factory tilt steering columns. Replaces Ford part number D0AA-9D793-AW.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

These are Grade "A" no excuses panels. This panel can be rather difficult to fix so we suggest you buy the best from the get go considering the low price. These will have no filler, no damage and often times will still bear the original paint.Ford part # C9ZZ-6502010-A.

These are Grade "B" cowl cover panels. These units may have one or two small dents, but can be an easily straightened and made to be perfect. Ford part # C9ZZ-6502010-A.

Reproduction cowl center panel for Mercury Cougar and Ford Mustang.

Reproduction 2 piece cowl panel for the Mercury Cougar or Ford Mustang.Here's our video to help you fortify your Cougar!

Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.

Crankshaft oil slinger for all 351C or Cleveland engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines.  Ford part number D0AZ-6310-A.

Crankshaft oil slinger for all FE Ford V-8's, starting 1958 until at least through 1976. 1967-69 390 engines, 1968 427-4V engines, 1968-70 428, 428CJ, 428SCJ engines, 1958-66 352, and 1968-76 360 engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter 3-5/16 inches. Ford part number B8A-6310-A.

CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.

First generation Cougars 1967 and 1968, used a single bracket for C4 automatics and both 3 speed and 4 speed manual transmissions. This bracket also carried over to 1969 and 1970 with 351 or Boss 302 engines and either 3 or 4 speed manual transmissions. Ford part number C7ZZ-6A023-D. This part weighs 2.28 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 1/4" on center and the passenger side 2 3/4" on center.The reproduction Dynacorn part...

For all 1969 and 1970 Cougars with H code 351-2V and M code 351-4V engines and FMX automatic transmissions. This part weighs 2.66 pounds and when set on a level surface the height of the mounting hole on the driver side measures 3" on center and the passenger side 3 1/8" on center. Ford part number C9ZZ-6A023-A. *NOTE* The picture with all four crossmembers in a line shows the three versions of the small block C-6 and FMX units in the foreground and the last is the big block C-6 unit. Notice...

This is the reproduction cross member offered by most of the Mustang vendors. It is over 1.5 Lbs lighter than the factory cross members. We highly recommend purchasing our remanufactured, re-enforced cross member. It is crucial that you use the correct tapered bolts when installing these.

Good original part that has not been noticeably twisted, bumped, bent, or heavily rusted. Notice the factory indentations that are a result of the manufacturing process (dent from jig). Also know that there is always at least a couple minor dings or scrapes from decades of being the lowest point of the car. Much better fit than repro and note the repro is made from thinner gauge steel. Also know that we generally do not bead blast our used parts before sending them but often we show them on...

This reproduction radiator support crossmember is correct for the 1967-68 Mercury Cougar and Ford Mustang, but will work on any 1967-70 Cat or Pony.Replaces Ford # C7ZZ-6510852-B or C9ZZ-6510852.

New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD. 

This listing is for a pair of walking cat die cast chrome cufflinks. These would be great for the serious collector who may want to add a bit of Cougar flair to outfit when hitting the town, or simply just another bit of memorabilia to add to their collection.  Walking Cat measures 1-3/16" across.

Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom made Walking Cat belt buckle for the Cougar die hard. This would make a great gift for anyone who lives and breathes everything Cougar. The buckle is bare, unpainted and ready for you to customize how you see fit. We're not sure how we ended up with this awesome collectable, but it's definitely one of a kind and the only one we know of, so when it's gone it's gone!  Measures 3 3/8" x 2 1/4"

1970 Front unibody cut, these 1970 Mercury Cougar front structures all have reinforced shock tower braces like the 428 Cobra Jet Mustangs. Additionally these have the cutouts on top of the radiator core support for the Mustang twist locks. Mustang guys, please note, we do not have them without these braces. This cowl has the holes for the factory air conditioning. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No...

1970 Front unibody cut, these 1970 Mercury Cougar front structures all have reinforced shock tower braces like the 428 Cobra Jet Mustangs. Additionally these have the cutouts on top of the radiator core support for the Mustang twist locks. Mustang guys, please note, we do not have them without these braces. This cowl only has the holes for the heater hoses only, not cut for factory air conditioning. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or...

Comes with good shock towers, front aprons, and core support. This is a great value for those that need to replace multiple parts upfront as you will not only get factory joined parts that will save you money and time, but it will also  preserve the value of your car. With a clean Western cut like this, one should be able to install it so that nobody would ever know your car has had anything replaced. You will have to call to order this one. Expect to pay about $300 for crating and...

Single cylinder head from 1970-73 Mercury Cougar with H code 351C-2V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.04 and 1.65 inch valves, and the chambers measure out at 78.2 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-J. 2V in the...

Single cylinder head from 1970 Mercury Cougar H code 351W engines, 351-2V. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0OE-6090-C. 1970 351 Windsor engine, not to be confused with the 351 Cleveland engine from the same year.These weigh 53 lbs. each, and cannot be...

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash.

Used highly collectible Dan Gurney slot car racing track made by the Republic Tool and Manufacturing Corporation in Los Angeles California. Open box and lightly used. Both cars are intact, and the decals have been placed on the the vehicles and the track. Everything is good condition, but the cars have not been tested and the red car has had it's wheels painted. Other than that, this is a rare and truly great find. Features the Mercury Cougar Logo on front of the box.