All Products

Alternator mounting bracket for 1971 Mercury Cougar and Ford Mustang 429 Cobra Jet engines. Also fits 1970-71 Mercury Cyclone and Ford Torino 429CJ's. Ford stamped D0SE-10156-A. *Note - This bracket is not for the thermactor smog system as found on 429 Super Cobra Jet engines.

D0WY-9A225-A "L" shaped mounting bracket for the rear evaporative vapor separator, mounts in the drivers side trunk well. *Note - This is only a small part of the 9B004 assembly.

There is not a special part number for this mounting bracket that was originally spot welded to the front of the headlamp switch. We offer these for use with our reproduction headlamp switch. This adapter or retainer is needed to correctly keep the headlamp switch at the correct angle to the lower metal dash. 1967-68 Mercury Cougar.

Original FoMoCo used part in good condition. Casting number is C7AA-3A772-B. Fits both small and big block. This is really the way to go... Original OEM FoMoCo with all the right markings and about half the price or repro. Ford Part #: C7ZZ-3A732-B.

This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb. You can find our reproduction pair of brackets here. ...

These aluminum ninety degree brackets are what fastens the XR7 chrome boot moulding to the quarter panels. The beltline weatherstip also attaches to them. These parts are only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass

This aluminum ninety degree bracket is what fastens the XR7 chrome boot moulding to the quarter panel. The beltline weatherstip also attaches to it. This part is only used on the XR7 convertible as the standard convertible boot trim ends at the rear edge of the quarter glass, whereas the XR7 diecast trim goes all the way to the door jamb.You can find our reproduction pair of brackets here. ...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529035-A

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529034-A

Metal stamped brackets used to mount the radiator on saddle mounts styles only. Rubber insulators not included.Check out our video on Radiator and Fan upgrades below:

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is the way to go. Consider adding the upper rubber pieces to your order, see related items.Not for use on 17-20" wide standard cooling radiators. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on...

When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is the way to go. Consider adding the upper rubber pieces to your order, see related items.These brackets came in two configurations, most has the round mounting holes but some were punched square. Not for use on...

Sometime during the 1970 model year, this bracket was used on cars with 24 inch radiators. At the beginning of the year the 1969 bracket was being used. Pretty much indistinguishable when mounted on the car. When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is...

This special bracket gets glued to the windshield. Rear view mirror bracket gets mounted to it. Glass bead blast it or just use a wire brush and it is ready to go!

These plastic mounting brackets came in black or gray. These kinds of minor differences can often be attributed to different suppliers. We have many that still retain the LH & RH decal for those of you trying to obtain a show car level in your restoration. The backside of this bezel will be marked LH - TOP.D0MB-15A470-B

These plastic mounting brackets came in black or gray. These kinds of minor differences can often be attributed to different suppliers. We have many that still retain the LH & RH decal for those of you trying to obtain a show car level in your restoration. The backside of this bezel will be marked RH - TOP.D0MB-15A432-B

Reproduction thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Painted Ford engine blue a shown. Nice reproduction, made in the USAFord part # C8AE-9C486-A.

Thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Ford part # C8AE-9C486-A. *RESTORATION TIP* This bracket was painted Ford Engine blue from the factory.

Ninety degree bracket needed to mount the starter safety switch to the column tube in 1967.

Used mounting bracket for the sunroof motor on the 67 - 70 Mercury Cougar. This bracket is only used with the 67 - 70 power sunroof motor.

Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. Used on both the 351-2V and 351-4V engines with original Ford cast iron intake manifolds. There are two versions of this bracket per the MPC, it is such a minute detail, it is hardly worth listing separately.Replaces Ford part number D1ZZ-9728-E and D1AZ-9728-H.

Used bracket that mounts in the rear Carburetor mounting hole of all 1970 351 Cleveland 2 barrel engines. Has the square hole that holds the factory throttle cable. This bracket is identified by the hump or curve midway between the carburetor mounting studs.Replaces Ford part number D0OZ-9741-A.*Note - Not for use with 351 Windsor engines, or M code 351C-4V engines.

Bracket that mounts in the rear Carburetor mounting holes of all 1969 and 1970 351 Windsor 2 barrel or H code engines. Has the square hole that holds the factory throttle cable.Replaces Ford part number C9ZZ-9741-D.

Bracket that mounts to the rear Carburetor mounting holes of all 1969 351-4V and 428 Cobra Jets or Super Cobra Jets. Has the square hole that holds the factory throttle cable and hole for the return spring. *Note - This is not a flat bracket like the 1970 351C-4V. There is a distinct drop in the bracket to clear the underside of the Holley carburetor on Cobra Jet equipped cars.

Bracket that mounts to the rear Carburetor mounting holes of all 1969 351-4V and 428 Cobra Jets or Super Cobra Jets. Has the square hole that holds the factory throttle cable and hole for the return spring.  Replaces Ford part number C9ZZ-9741-B. *Note - This is not a flat bracket like the 1970 351C-4V. There is a distinct drop in the bracket to clear the underside of the Holley carburetor on Cobra Jet equipped cars This is the original factory bracket, reproduction brackets have...

Used with factory "Autolite" carburetor and aluminum carburetor spacer unique to the 1969 Cougar. Bracket that mounts to the rear Carburetor mounting holes of all 1969 390-4V. Has the square hole that holds the factory throttle cable and hole for the return spring. Has a distinct dip or curve, midway between the mounting holes for the carburetor.Replaces Ford part number C9ZZ-9741-C.

Nice reproduction of the Boss 302 throttle bracket as found on the G code Boss2 cars. Includes 1969-70 Cougar Eliminator and Mustang. Similar to the 428 Cobra Jet bracket but with an extended spring tab.

Original FoMoCo used windshield wiper motor mounting bracket for your 1969-70 Mercury Cougar or Ford Mustang. This used bracket comes with grommets, for all 1969-70 Cougar and Mustangs. Mounts under the cowl cover at the windshield. Ford part # C9ZZ-17496-A.

Original FoMoCo used two speed windshield wiper motor mounting bracket for your 1971-73 Mercury Cougar or Ford Mustang. This used bracket comes with grommet for all 1971-73 Cougar and Mustangs. Ford part # D1ZZ-17496-B.

Reproduction mounting bracket / retainer for the XR7G headlight eyelid emblem. The emblem will attach to this bracket with double sided tape or epoxy, whichever you choose. Emblem and 3/8" 10/24 nuts not included.

If your Cougar came from a region that uses road salt your buckets are probably rusted in the corners or worse. Our dry "West Coast" buckets are 100% rust free and the mounting tabs are not broken from the removal of stubborn bolts. They will not be bent or damaged in any way. Keep in mind we do have grade B brackets for much less that only have minor bends or blems that could be easily corrected. *NOTE* These parts are far more important than most people realize. If they structural integrity...

These driver quality buckets are solid but will have a small bend, hairline crack or the beginnings of rust in a corner. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in these brackets are very powerful and if these brackets do...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable.  NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS.   *NOTE* These...

If your Cougar came from a region that uses road salt your buckets are probably rusted in the corners or worse. Our dry "West Coast" buckets are 100% rust free and the mounting tabs are not broken from the removal of stubborn bolts. They will not be bent or damaged in any way. Keep in mind we do have grade B brackets for much less money that only have minor bends or blems that could be easily corrected. *NOTE* These parts are far more important than most people realize. If they lack structural...

These driver quality passenger side headlight buckets are mostly solid but will have a small bend, hairline crack or the beginnings of rust in the corner closest to the battery. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable. NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS. *NOTE* These parts are far more...

These brackets are required to mount the optional rear bumper guards. They are not an exact reproduction but functionally they are spot on.Installation hardware is hard to come by, so you should hang on to yours and re-use them.Sold as a pair

These are the brackets required to mount the optional rear bumper guards. They mount behind the rear valance and are often overlooked when people part out a Cougar. *NOTE* As is often the case, service replacement parts are painted satin black and the originals installed on the assembly line were left natural. The mounting brackets are in fact supposed to have a natural finish if your car came with them from the factory.

One year only, 1967 390 only used brackets for use in conjunction with original 1967 radiator. If you are putting a reproduction radiator in your 1967 then the 1968-1970 lower brackets are what you are after. Check out our video on Radiator and Fan upgrades below: ...

Metal-stamped 1968 - 1970 Lower Radiator Mounting Brackets feature exact detail and proper fit. Painted dull black. Sold in Pairs. Rubber insulators not included. Replaces Ford part # C8ZZ-8052-A. Check out our video on Radiator and Fan upgrades below: ...

Our used lower cradle brackets for the 24" wide radiator will always have some amount of damage as shown. We will not send you mangled junk that is heavily rusted but they will require some amount of straightening due to their vulnerable location. These also work with the 67 small block and big block when putting in a 68-70 24" radiator but keep in mind the 1967 cars are not pre-drilled as are the 1968-1970 Mustang and Cougar.We are out of the 1970 style of brackets. We only have the two...

Sold as a pair. One long and one short bracket. Fits 1971-73 Mercury Cougar and Ford Mustangs that have original style radiators.  Mounting bolts not included. Replaces Ford part number D0OB-8B359 RH, and D0AB-8K007 LH. Check out our video on Radiator and Fan upgrades below: ...

D0WY-9A188-A and D0WY-9A188-B Mounting bracket for the evaporative vapor separators, mounts in the drivers side trunk rail. Two brackets paired up. *Note - This is only a small part of the 9B004 assembly.

This kit includes all new hardware, and both brackets. Mounting diagram not included (you can save and print the photo above). As shown, 1967 - 1968 rear bumper guards mount 17.5" from the center line of the car. Clip and bolt hardware kit will be new pieces.

U-shaped bracket that mounts the long flat part of the front sway bar to the chassis. Clamps sold individually, two needed for attaching front sway bars. This clamp with the folded ears on the sides is for the 7/8 and 15/16 inch front sway bars.

Concours correct reproduction of the front sway bar clamps used on all 67 - 70 Cougars and Mustangs with the competition suspension option, or 15/16th" sway bar. Never available until now. Exactly like the originals in every detail. Standard for all Shelbys, Boss 302s, and Cobra Jets. Stamped and formed just like the originals.

Pair of U-shaped brackets that mounts the long flat part of the front sway bar to the chassis. Two needed for attaching front sway bars. *Note* 1969 and 1970 Cougars with the Competition Handling Package which included all with 428CJ and Boss 302 engine packages, used a different bracket with a Ford part number of C7ZZ-5486-A.Replaces Ford part number #: C6OZ-5486-B.