All Products

New Old Stock Package tray speaker frame. Ford part number C8ZZ-18978-A, casting number C8ZA-18978-A.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528519, Mercury MPC # D1WY-6528011-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528518, Mercury MPC # D1WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

New old stock passenger side rear quarter panel extension. 1967-68 Mercury Cougar. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

This is the seal at the back of the booster on the Midland-Ross units.

Rear seat bottom or lower cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number C9WB-7663120.*Note - Does not fit coupe or fastback.Lower frame measures 46" at it's widest point and 18.5" high This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Rear seat bottom or lower cushion from any 1967-70 Mercury Cougar. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C7WB-6563120. This part number or engineering number would have originally been stamped into a tag that was attached to the bottom side of the seat. *Note - Will not fit Mustang, Mustangs 1967-68 seat bottoms (C7ZB-6563120) are the same width as Cougars, but the seating portion...

Rear seat bottom or lower cushion from any 1971 Mercury Cougar or Ford Mustang coupe or hard top only. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Only fits 1971 cars due to the seat belt location in the floor. 1972-73 seats are a bit narrower, due to the seat belt retractors in the side panels.Replaces Ford part number D1ZB-6563120.*Note - Excludes 1972-73 Mustang and Cougar.

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Only fits 1972-73 cars due to the seat belt location in the side panels. 1971 seats are a bit wider.Replaces Ford part number D2ZB-6563120.*Note - Excludes 1971 Mustang and Cougar.

Rear seat back or upper cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C9WB-7666700. This part number or engineering number would have originally been stamped into a tag that was attached to the bottom side of the seat. Though these seem to fit in a 64-70 Mustang convertible, the correct engineering number that would...

Rear seat back or upper cushion from any 1967-70 Mercury Cougar. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C7WB-6566700.  This part number or engineering number would have originally been stamped into a tag that was attached to the back side of the seat.  There are claims that this part will also work in the Mustang coupe, but the 67 - 70 Mustang would have originally...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang coupe or hard top. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-6566700.*Note - Does not fit convertible.

This is from the Ford accessory catalog starting in 1968. This is a rear seat ash tray for cars without center console. Textured plastic construction with typical ash tray and receptacle as found on the rear of the console. FoMoCo boxed with Ford part number C8WY-6504803-A. The textured plastic box has a casting number of C8WA-6566836-A. Will fit 1967 Mercury Cougars too. Included are original instructions for installation. 

This is the seat belt bezel located on the rear interior panel on your 72 - 73 Cougar or Mustang. Without it, your belt would retract back into the panel and you'd have to remove the whole thing just to get to the belt again. These bezels are very hard to come by, and we have yet to find anyone who reproduces them. Keep in mind that these bezels have been sitting for over 40 years, so the plastic has most likely become hard and chalky. When ordering, be sure to mention what color you need, and...

This rear segment exhaust system is manufactured right here in the good old USA from original 1968 and 1969 Mercury Cougars. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This 2-1/4 inch rear segment exhaust system is manufactured right here in the good old USA from an original 1971 M code Cougar with the 351C engine. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they...

This 2-1/4 inch rear segment exhaust system is manufactured right here in the good old USA from an original 1969 M code Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This rear segment exhaust system is manufactured right here in the good old USA from an original 1967 S code Cougar. It is an OEM style direct replacement system that includes: 2 intermediate pipes, 2 mufflers, 1 transverse resonator, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so...

This 2-1/4 inch rear segment exhaust  system is manufactured right here in the good old USA from an original 1971 429 Cobra Jet Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept...

This 2-1/4 rear segment exhaust system is manufactured right here in the good old USA from an original 1969 R code Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

6x9 Replacement for OEM package tray speaker. Comes pre-wired with the stock style pigtail to plug in to your original wiring. Sold individually, 2 required per car.

Kit includes one pair of 25 watt speakers (50 watts total peak) with correct pigtails and one pair of correct speaker grills with the exact screen pattern as original. Correct mount spacing utilizes the factory holes in your package tray, hardware included. This kit is 100% correct for the 1967 or 1968, but will work on the 69 or 70 as well. The Cougar package trays for the 69 and 70 came perforated from the factory for speakers, so the grills are not necessary. Thanks for the plug Mark!: "My...

Very good reproduction of the speaker grille located on the package tray in the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. Includes the mounting hardware.  Sold individually.

Rear fender splash shield for the driver side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16103-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

The metal portion on the Mustang shield is identical to the 1967-68 Cougar rear shields, but the rubber is different between the Cougar and Mustang. We are in the process of trying to get the correct rubber for the Cougar. Replaces Ford Part # C7ZZ-16103-B.

Rear fender splash shield for the passenger side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16102-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

The metal portion on the Mustang shield is identical to the 1967-68 Cougar rear shields but the rubber is different between the Cougar and Mustang. We are in the process of trying to get the correct rubber for the Cougar. Replaces Ford Part # C7ZZ-16102-B.

Reproduction rear taillight panel lower structure / support for the 67 - 68 Cougar. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

D0WY-9A091-B Rear evaporative vapor separator, mounts in the drivers side trunk well. *Note - This is only a small part of the 9B004 assembly.

This special bracket gets glued to the windshield glass. Rear view mirror mounts on it. Plain finish. Replaces Ford Part #: C9AZ-17698-A.

Unlike the originals, the housing on this unit is hard plastic, not vinyl. The day / night function does not work well on this Chinese unit. Since we tell you up front that this is a substandard part that you will not be happy with, we will not accept returns. Keep in mind this is the EXACT mirror marketed by other vendors as "Good Quality". When you see this icon on a product, it means it's a sub-par item that we don't recommend, due to our own experience in handling and using this item on...

Black grade A mirror assembly with re-silvered lens. This is the early rubber version that is big and bulky with a twist knob for the day / night feature. Found on early 1967 cars, later cars used a smaller mirror with either a twist or lever for the 'Day/Night' function. We also sell re-silvered lenses by themselves on an exchange basis. Sold outright, no core required.  In our observations 1967 Mercury Cougar XR7's were all black colored. Ford documentation lists possible part numbers...

Dark Ivy Gold / Dark Green grade A mirror assembly with re-silvered lens. This is the early rubber version that is big and bulky with a twist knob for the day / night feature. Found on early 1967 cars, later cars used a smaller mirror with either a twist or lever for the 'Day/Night' function. We also sell re-silvered lenses by themselves on an exchange basis. Sold outright, no core required.  In our observations 1967 Mercury Cougar XR7's were all black colored. Ford documentation...

Dark Red grade A mirror assembly with re-silvered lens. This is the early rubber version that is big and bulky with a twist knob for the day / night feature. Found on early 1967 cars, later cars used a smaller mirror with either a twist or lever for the 'Day/Night' function. We also sell re-silvered lenses by themselves on an exchange basis. Sold outright, no core required.  In our observations 1967 Mercury Cougar XR7's were all black colored. Ford documentation lists possible part...

This mirror came primarily on the 1969 Cougars, but have also been seen on the 1968. It has a forward /back flip lever to switch from day to night view. Comes in black only, case is of a hard plastic as opposed to the original hard vinyl case. The texture is not as heavy as original. Replaces Ford Part #: C7AZ-17700-G. This picture below shows the rear view mirror variations from 1967-1973. Also, check out our video showing rear view mirror replacement options: ...

Not an exact replacement, but a decent replacement if you have a rear view mirror that the silver is peeling on. Includes new glue on mounting tab (bracket). Replaces Ford Part #: C8AZ-17700-A. This picture below shows the rear view mirror variations from 1967-1973. Also, check out our video showing rear view mirror replacement options: ...

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

NOS service replacement flip style rear view mirror assembly. Lens shows some staining from years of being on the shelf . See reference photos above. In our observations 1967 Mercury Cougar XR7's were all black colored. Ford documentation lists possible part numbers of C7AB-17702 and service replacement box shows C7AZ-17700-F1A. This picture below shows the rear view mirror variations from 1967-1973. Also, check out our video showing rear view mirror replacement options: ...

This mirror came primarily on the 1968 Cougars, but have also been seen on the 1969. It has a twist lever to switch from day to night view. Comes in black only, case is of a hard plastic as opposed to the original hard vinyl case. The texture is not as heavy as original. Replaces Ford Part #: C7AZ-17700-G. This picture below shows the rear view mirror variations from 1967-1973. Also, check out our video showing rear view mirror replacement options: ...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. These rear view mirror lenses are sold on an exchange basis.  Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind...

Restored rear view mirror lens for the Mercury Cougar or Ford Mustang. Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard.  We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind glass is porous and is prone to staining. Often times these faint stains do not show up until...

These rear view mirror lenses are sold on an exchange basis.  Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind glass is porous and is prone to staining. Often times these faint stains do not show up until the glass...

Rear defog conversion kit for 1970 Mercury Cougar XR7's. Includes switch and DEFOG panel, switch wiring, power lead, long harness to blower motor, and blower motor and grille cover which installs in the rear package tray. Please see your electrical schematic for connection details. This set up can easily be installed into a 1969 XR7 as well. You may need to purchase an accessory lead and buss bar if your car was not equipped. Everything has been tested to be in working condition.

Rear defog conversion kit for any 1968 Mercury Cougar or Ford Mustang Coupe. Includes switch with bracket that goes under the edge of the dash, wiring harness to the accessory plug (for sure on all 1968 Standard and XR7's), long harness to blower motor, and blower motor and grille cover which installs in the rear package tray. Please see your electrical schematic for connection details. Everything has been tested to be in working condition. *NOTE - Early 1967 Cougars do not have the proper...