All Products

Used XR7 grade "B" main headlight wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs as where grade "A" harnesses will be rare uncut beauties. 1972 Mercury Cougar XR7 models (before 12/1/1971) only. Not compatible with Standard model Cougar...

Reproduction under hood wiring harness for the Mercury Cougar. These are concours quality EXACT reproductions! Every wire, every stripe and connection is exact. We have many good used wiring looms in stock for front, under dash and rear, give us a ring or email for details. Our reproduction harnesses are made by seasoned craftsmen who use only the original Ford drawings and EXACT materials. Many of the connectors are NOS.Replaces Ford part # C7WY-14290-H.

NOTE: The firewall grommet does not have the correct gap spacing and will need to be heated and stretched, or cut to make fit. Reproduction under hood wiring harness for the Mercury Cougar. These are concours quality EXACT reproductions! Every wire, every stripe and connection is exact. We have many good used wiring looms in stock for front, under dash and rear, give us a ring or email for details. Our reproduction harnesses are made by seasoned craftsmen who use only the original Ford...

Replaces Ford Part # C9WY-14290-LR. Pictured is a 1969 XR7 under hood wiring harness. These are concours quality EXACT reproductions! Every wire, every stripe and connection is exact. We have many good used wiring looms in stock for front, under dash and rear, give us a ring or email for details. Our reproduction harnesses are made by seasoned craftsmen who use only the original Ford drawings and EXACT materials. Many of the connectors are NOS. *Customer feedback* Mercurycougar.net: I was...

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

OEM Style Universal Exhaust Hanger Bracket 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.

All applications, attaches the drive shaft U-Joint to rear end pinion yoke. Sold in pairs, complete with nuts. Perfect used. Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...

Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.

Reproduction universal joint forged from high strength alloy steel that is cross w/ an anti-corrosion coating. This unit fits the transmission end drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (See Chart). this unit also features a grease fitting for an extended life. span 3.60" cup size 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-G.

Reproduction front universal joint that fits on transmission end of the drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-G.

Reproduction universal joint forged from high strength alloy steel and crossed w/ and anti-corrosion coating. Fits the differential end of the drive axle on all 289, 302, 351 Windsor as well as most 351 Clevelands (See Chart). Includes a grease fitting for an extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction alloy rear universal joint for the Mercury Cougar or Ford Mustang. This unit is forged from high strength alloy steel crossed w/ an anti-corrosion coating. This universal joint fits the differential end of the drive axle on all Eliminators and cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. span 3.5" cup size 1.00" and 1.12" Replaces Ford part # C3AZ-4635-H. ...

This reproduction universal joint fits the differential end of the drive axle on all Eliminators and other cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. Replaces Ford part # C3AZ-4635-H.

Used original dealer upholstery and interior options catalog for the 1967 Cougar, Monterey, Brougham, Marquis, Montclair, Colony Park, Commuter, S-55 and Park Lane. These catalogs were customized to each dealership so there might be a few variations out there, but it's filled with tons of information on interior upholstery, carpet and roof coverings. Complete with inner flip out mini catalogs featuring colors and swatches.   These books are very rare and hard to come by and would be...

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

NOS upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1969-70 Mercury Cougar or Ford Mustang. Ford part number C9ZZ-7521-A.

NOS upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, and contours. Ford part number D1ZZ-7521-B.

Nice quality reproduction of the upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, and contours. Ford part number D1ZZ-7521-B.

Complete kit with shaft for one side. Includes grease seals and zerk fittings. Note! Often times the fine threads in the upper control arms will be worn to the point of being stripped. To keep this kit properly in place you may have to tack weld the threaded caps to the control arms in a couple of places.

Sold individually, two required per car. These are brand new, not rebuilds. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford Part #: C7DZ-3082-A. Fits 1967-70 Mercury Cougar and Ford Mustang. We have found that this economy version does not fit 1971-73. There just is not enough clearance for this unit to bolt into the shock tower. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Sold individually, two required per car. These are brand new, not rebuilds. Please click onto the listing of our NOS arms to see side by side comparison pictures. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford part # C7DZ-3082-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

New quality upper control arm shaft kit. Fits all 1967-73 Mercury Cougar and Ford Mustang, also Maverick/Comet 1970-77, Fairlane 1966-70, Torino/Cyclone 1968-71. Comes with all parts shown. This is a much better design than the original Ford design. The down fall is it does not look at all like the original Ford kit. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Reproduction upper cowl conversion panel for doing a RIGHT HAND DRIVE conversion on their 67 - 68 Mustang. 

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654607-A and are marked L.H. for the passenger side.

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654606-A and are marked R.H. for the passenger side.

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C7ZZ-6522800-C. ...

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the driver side rear interior panel on a 1969-70 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Grade A used, no obvious dents or rust.Basic Ford part number is 7631005. 

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the driver side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at least...

Metal portion of the passenger side rear interior panel on a 1969-70 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Grade A used, no obvious dents or rust. Basic Ford part number is 7631004.  *Note - Excludes Late 1970 with larger power window bezels.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Metal portion of the passenger side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C7ZZ-6522800-C.

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: D0ZZ-6522800-A. ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Up for grabs is a very rare USPS Promotional Pony Car Stamp Collection Poster featuring a 1967 Mercury Cougar XR7 GT, 1969 Ford Mustang Boss 302, 1969 Chevrolet Camaro Z/28, 1970 Dodge Challenger R/T and a 1969 AMC Javelin SST. These posters were issued to Post Offices to be hung up on 6/18/22 and were to be taken down and destroyed on 11/12/22. We were lucky enough to get our hands on one and we're giving you the opportunity to add this piece of art to your collection!...

Key stock for 1967-73 Ford V-8 engines 3/16" square straight keys. Ships in 4 inch lengths, cut to fit the different applications. Common sizes 289/302 1-13/32", 351 1-3/4", etc.

These are the cheap knockoff clamps sold by most Mustang venders as correct stamped clamps. Sold in a convenient set of 10. We highly recommend ordering the correct CONCOURS clamps! Replaces Ford Part #: C5ZZ8287-8.

Used vacuum actuator for controlling the center A/C vent on certain 1969-70 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Studs are on 1-1/4 inch centers. Common single port vacuum valve is on 2-1/4 inch centers. Ford part number C9ZZ-18A318-A. ...

Used vacuum actuator for controlling the center A/C vent on any 1971-73 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Ford part number D1ZZ-18A318-A.