All Products

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford Mustangs equipped with drum brakes.

Fuel and brake line fastener kit. Fits all 1967 Mercury Cougar and Ford Mustang with V-8 engines and 2 piece fuel line from tank to pump. Early production 1967 cars used a 1 piece fuel line from the gas tank to fuel pump. Eventually Ford installed 2 piece fuel lines during 1967. This is only for the two piece fuel line.*Note these are for the original and reproduction style fuel lines that were 5/16 thick, which was unique to 1967 production.

Rear Wheel Cylinder (7/8", Left Rear). For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller.The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting. Replaces Ford Part #: C20Z-2261-B, C3AZ-2261-B, C4TZ-2261-A, C60Z-2261-A, D3TZ-2261-A, D3ZZ-2261-A. ...

Rear Wheel Cylinder (7/8", Left Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. You can find the premium concours correct version here.

Rear Wheel Cylinder (7/8", Right Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller.You can find the premium concors correct version here. Replaces Ford Part #: C20Z-2262-B, C3AZ-2262-B, C4TZ-2262-A, C60Z-2262-A, D2ZZ-2262-A, D3TZ-2262-A, D3ZZ-2262-A. ...

Rear Wheel Cylinder (7/8", Right Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting.Replaces Ford Part #: C20Z-2262-B, C3AZ-2262-B, C4TZ-2262-A, C60Z-2262-A, D2ZZ-2262-A, D3TZ-2262-A, D3ZZ-2262-A. ...

Rear Drum Brake Wheel Cylinder for 390, 427, 428 w/ Front Disk Brakes (13/16", Right Hand & Left Hand same) You can find the premium concours correct version here. Replaces Ford Part #: C7ZZ-2262-A

Rear Drum Brake Wheel Cylinder for 390, 427, 428 w/ Front Disk Brakes (13/16", Right Hand & Left Hand same) The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting. Replaces Ford Part #: C7ZZ-2262-A

Rear Wheel Cylinder (29/32", Right Hand) Fits either Right Hand or Left Hand. Sold individually, 2 required per car. Replaces Ford Part #: C3OZ-2262-B and D2ZZ-2262-B.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits into a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2062-B or C9TZ-2062-B.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits in a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part #: C3OZ-2062-B, D2ZZ-2062-A, & D3ZZ-2062-A.

Rear Wheel Cylinders for 4 Wheel Drum Brakes (15/16", LH). Replaces Ford Part #: C7AZ-2262-C.

Reproduction passenger side (right hand) wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits into a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part # C3OZ-2061-B, D2ZZ-2061-A, & D3ZZ-2061-A.

Rear Wheel Cylinder 29/32 inch bore, right hand fits passenger side of any 1969 with 2 inch wide rear brake shoes. This wheel cylinder orients the hard line to the rear of the vehicle. 1970-73 wheel cylinders are oriented towards the front.

Rear Wheel Cylinder for 4 Wheel Drum Brakes (15/16", RH) Replaces Ford Part #: C7AZ-2261-C.

Reproduction drum brake backing plate hole cover plug. Replaces Ford Part # 8A-2092.

Fuel and brake line fastener kit. Fits all 1967 Mercury Cougar and Ford Mustang with V-8 engines and 1 piece fuel line from tank to pump. Early production 1967 cars used a 1 piece fuel line from the gas tank to fuel pump. Eventually Ford installed 2 piece fuel lines during 1967. *Note these are for the original and reproduction style fuel lines that were 5/16 thick, which was unique to 1967 production.

Used passenger side (right hand) front drum backing plate for 2-1/4 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane /Torino equipped with the 289 or 302 engine. Typically when these cars were equipped with the small block V8 they came with 10" x 2-1/4" brakes shoes. Ford part # C3OZ-2012-B. *NOTE* Normally 6 cylinder Mustangs came with 9" x 2-1/4" drum brakes on the front.

Used driver side (left hand) front drum backing plate for 2-1/4 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane / Torino with the 289 or 302 engine. Typically when the car can with the small block V8 they came with 10" x 2-1/4" brakes shoes. Ford part # C3OZ-2013-B. *NOTE* Normally 6 cylinder Mustangs came with 9" x 2-1/4" drum brakes on the front.

Used driver side (left hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar or Ford Mustang, and Fairlane / Torino equipped with 351 or larger V8 engines. Ford part # C9OZ-2013-B. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

Used passenger side (right hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane / Torino equipped with the 351cid or larger V8 engine.Ford part # C9OZ-2012-A. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

If you watch our booster video you will see we have a clear distaste for most of the offshore boosters offered today. What caught our attention about this new product was that it looked like a real deal 67-9 Midland brand booster! We went the next step and sent it to the world's foremost leading authority on said boosters (Booster Steve in Portland OR) so he could put it through some rigorous testing and examination. At first he was very hesitant to have us waste the postage to send it but two...

Quality rebuilt LH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included. Check out out video on converting from drum to disc brakes below: ...

Remanufactured driver side (left hand) disc brake caliper for the 1967 Mercury Cougar, Ford Mustang, or other medium sized Ford or Mercury car. This is a factory replacement, rebuilt caliper that may or may not be an original Bendix casting. Caliper only, brake pads NOT included. *NOTE* Does not include hard lines or any other brackets not shown. Cores must be suitable for rebuilding and be complete.

Used driver side (left hand) Kelsey Hayes two piston disc brake caliper as factory installed on 1967 Cougar, Mustang, and Fairlane. 1967 was unique in that it had a 7/16" inlet fitting as where earlier Mustang calipers used a 3/8" inlet fitting. Thunderbird and full sized Ford cars used a larger version of this caliper. Tough parts to find in rebuildable condition. Ford part # C7OZ-2B121-C.

Quality rebuilt RH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included. Check out out video on converting from drum to disc brakes below: ...

Remanufactured passenger side (right hand) disc brake caliper for the 1967 Mercury Cougar, Ford Mustang, or other medium sized Ford or Mercury car. This is a factory replacement, rebuilt caliper that may or may not be an original Bendix casting. Caliper only, brake pads NOT included. *NOTE* Does not include hard lines or any other brackets not shown. Cores must be suitable for rebuilding and be complete.

Used passenger side (right hand) Kelsey Hayes two piston disc brake caliper as factory installed on 1967 Cougar, Mustang, and Fairlane. 1967 was unique in that it had a 7/16" inlet fitting as where earlier Mustang calipers used a 3/8" inlet fitting. Thunderbird and full sized Ford cars used a larger version of this caliper. Tough parts to find in rebuildable condition. Ford part # C7OZ-2B120-C.

Replaces Ford Part # 382713-S Sold individually

Sold as a Pair. Ford Part #: C8AZ-2B296-A

part# 384114-S100 Sold individually

Replaces ford Part # 381776-S 3/8-24x2 1/2 9/16 Sold individually, 1 used per side. The other 3 bolts are short, see item 41137.

Replaces Ford Part # 379787-S 3/ 8-24x1 1/2 9/16 Sold individually, 3 used per side. There is one long bolt per side, see item 41138.

Used disc brake distribution block for 1968 and 1969 Cougar and Mustang with factory disc brakes. Mounts to the driver side fender apron with two nuts. Bare block without brake switch or Proportioning valve. Look for our listing for 1968 - 1969 Brake Distribution Block Assembly for a unit with the switch and proportioning valve with steel flared connecting lines. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # C8ZZ-2B257-A. Here’s a video to help you...

Used drum brake distribution block for the Mercury Cougar or Ford Mustang equipped with front drum brakes. Mounts to the driver side fender apron with a single bolt. Bare block without brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # C7ZZ-2B257-C.Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

Used drum brake distribution block for Mercury Cougar and Ford Mustang with front drum brakes. This unit mounts to the driver (left hand) side fender apron with a single bolt. Bare block without the brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # C8ZZ-2B257-B.Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

Used drum brake distribution block for Mercury Cougar and Ford Mustang equipped with front drum brakes. This unit mounts to the driver side fender apron with two nuts. Bare block without brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # D0OZ-2B257-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Reproduction disc brake distribution block and proportioning valve assembly for the Mercury Cougar or Ford Mustang with factory disc brakes. This will also work on your 1968 - 1969 Fairlane / Torino / Montego / Ranchero / Cyclone & Cobra equipped with power disc brakes in the front if you carefully remove the wedged on stamped steel mounting bracket and reuse your original bracket. Mounts to the driver side fender apron with two nuts. With this assembly you will get a distribution block, brake...

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

These new brake drums are perfect replacements for tired and thin originals on you Cat or Pony. Fits cars with either the 2 1/4 inch or 2 1/2 Inch shoes. Front drums do not include studs or a hub. Drums Provide Consistent Quality & Reduced Noise.; Drums Are Vehicle Specific & Meet Federal Safety Standards.; Castings Meet Sae J431/g3000 Specifications For Proper Tensile Strength.; Machined To Control Perpendicularity & Run-Out For Optimal Performance & Brake Life.Also fits V8...

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 53.9 mm Center Bore Diameter : 61.8 mm Height : 84.5 mm Maximum Discard Diameter : 255.52 mm O.D. : 295.5 mm Replaces Ford Part #: C3OZ-1126-B.

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 71.6 mm Center Bore Diameter : 61.8 mm Maximum Discard Diameter : 256.3 mm O.D. : 296.3 mm Replaces Ford Part #:C2OZ-1126-B

STOPFLEX incorporates a special 4 layer design for superior strength and virtually no volumetric expansion. It starts with a Teflon PTFE core (liner) which is wrapped first in a Kevlar braid, followed by an elastomer barrier and then it's strengthened further by the outer stainless steel braid. Replacing original equipment rubber hoses with STOPFLEX stainless steel braided hoses will increase braking performance by doing away with the soft spongy brake pedal. Rubber hoses expand, with the...

STOPFLEX?? incorporates a special 4 layer design for superior strength and virtually no volumetric expansion. It starts with a Teflon PTFE core (liner) which is wrapped first in a Kevlar braid, followed by an elastomer barrier and then it's strengthened further by the outer stainless steel braid. Replacing original equipment rubber hoses with STOPFLEX?? stainless steel braided hoses will increase braking performance by doing away with the soft spongy brake pedal. Rubber hoses expand, with the...