All Products

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

Used rubber washer for the locking pawl cable to cable guide used for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit fits against the cable side of the ninety degree angle. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Used on all four 1967 belts for a total of 8 per car. Found to be slightly dished on most examples we see.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

Used on the retractors.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

These new taillight mounting washers are sold individually for your Mercury Cougar. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Same as 69-73 but with no markings.

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1967 tilt-away steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Water By-Pass Hose with 351W Motorcraft® logo and part number imprinted in white ink. Stamped with C9OE-8597-D.

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-A. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-J. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8OE-D. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Cast Iron Water Pump for the 1967, 1968 and 1969 small block. Has six vanes on the impeller. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand all indicate that this change took place at the very beginning of the 70 production year so that the 351C and 351W would use the same water pump. Replaces Ford Part #: D3UZ-8501-A or C5OZ-8501. ...

OEM replacement water pump for the 351 Cleveland. Gasket included. Replaces Ford Part #: D0AZ-8501-E.

OEM replacement Water Pump for the 351 Windsor. Gasket included. Replaces Ford Part #: D0OZ-8501-A.

Light duty OEM Replacement cast iron water pump for any Ford FE 390 / 427 / or 428CJ. Gaskets included. No Core required Replaces Ford Part #: C8AZ-8501-A.

Dated 4G20, July 20, 1964.Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5D26 or April 26, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump...

Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5D26 or April 26, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Dated 5F7 June 7, 1965. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5F7 or June 7, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings...

Dated 6A13, January 13, 1966. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 6A13 or January 13, 1966. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water...

0D13  April 13, 1970 dated.  Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C9AE-8505-A. Found on many Ford 390 and 428CJ engines from 1969-70. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Rebuilt water pump, Ford casting C9AE-8505-A, dated 9A9 January 9, 1969. Fits any 390 or 428 Cobra Jet.

Rebuilt water pump, Ford casting C9AE-8505-A, dated 9L25, November 25, 1969. Perfect for late Dec - Jan 1970 428 Cobra Jet. 

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

Reproduction water bypass plate for all Ford 351C engines. This is an original style brass restrictor plate for 70-73 Cougar, Mustang, Torino etc.Must be used in conjunction with the correct 180 degree thermostat.For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

New water restrictor plate for the Mercury or Ford equipped with the 351 Cleveland engine. It has been an accepted fact for decades now that the 351C bypass system was not the greatest idea Ford ever came up with. The unique 351C thermostat "hat" never seals well, causing a certain portion of coolant to just circulate through the block and never make it to the radiator. Years ago, Pantera enthusiasts (all Panteras had cooling issues from the factory BTW) found that if they soldiered a penny...

Used hot water tube connector, Grade B condition. Fits 1973 Mercury Cougar and Ford Mustang with EGR valve attached to the carburetor spacer plate. "H" shaped water tube connector with fitting for vacuum thermal valve that controls the EGR valve. These are seldom seen in any condition, Grade B used will have some rust through on the tubes, will be strong enough to slide heater hoses over what is left of the barb. Vacuum thermal switch switch not included. We also have a worse condition Grade C...

Used hot water tube connector, Grade C condition. Fits 1973 Mercury Cougar and Ford Mustang with EGR valve attached to the carburetor spacer plate. "H" shaped water tube connector with fitting for vacuum thermal valve that controls the EGR valve. These are seldom seen in any condition, Grade C used will have rust through in and on the tube ends. Probably want to get some tubing to fit the inside of the connector tubes, in order to clamp down heater hoses. Vacuum thermal switch switch not...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

Replaces Ford Part # : D1ZZ-7651325-A

This concours correct reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This Daniel Carpenter manufactured unit is made of slightly less dense material than the Midland unit, .75lb as compared to .85lb. If correctness is not an issue for you, you can get the Midland unit here. We have included a few comparison pictures so...

Economy overseas reproduction door perimeter seal. These glue to the perimeter of the doors and are held in by screws on both ends. Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

Premium reproduction Door Weatherstrip for the 1971 - 1973 Mercury Cougar or Ford Mustang.  These glue to the perimeter of the doors and are held in by screws on both ends.  Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

Sold as a pair, includes plastic fasteners. There are multiple manufacturers of this particular item and we feel after using them all on our own cars that we carry the best out there. Replaces Ford part #C7ZZ-6520530-A.

This offshore reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This overseas reproduction sold by Daniel Carpenter is simply another option to the US made version, and has been known to fit better than the US made weatherstrips. If correctness is not an issue for you, you can get the Midland unit...

Reproduction door glass to roof weatherstripping for your Mercury Cougar. These two long strips of rubber fit in the stainless steel channel that begins at the bottom of the A pillar and continues along the roof and ends at the base of the C pillar. Sold as a pair.Replaces Ford part # C5ZZ-6551222.

Reproduction door glass to roof weatherstripping for your Mercury Cougar or Ford Mustang. An inexpensive way to better seal the interior space of your Cougar or Mustang.Replaces Ford part #'s D1ZZ-6551222-A and D1ZZ-65223-A.

Reproduction door glass to roof weatherstripping for the Mercury Cougar and Ford mustang. These units are sold as a pair and are also known as the roof rail weatherstrip. Replaces Ford part # C9ZZ-6551222. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Rubber quarter window to door glass seal. Passenger side 1969 Mercury Cougar and convertible, and 1969 Mustang hardtop coupe and convertible. Ford part # C9ZZ-65214A14-A. *NOTE* Will not fit Mustang fastback or Mach 1. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Keep in mind not all gaskets are created equal... Many of these gaskets are made by two or three different makers. We have used these gaskets ourselves on our own Cougars with success, and know which ones fit correctly and which ones will stand the test of time. You may save a dollar or two buying elsewhere on some of these items but is it worth it? Ask the person selling the item if they personally have ever used the part. Replaces Ford part #D1ZZ-6542084. Installing the gasket yourself? you...