All Products

This is the trim piece that goes along the front edge of the hood. NOS condition, missing wrapper, this part does show shelf wear. Compared side by side to our restored trim, this part looks 2nd rate.Ford Part #: C9WY-16856-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

Core passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness.Ford part # C7WY-16856-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear. The tooling was often near the end of its life, so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16856-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS passenger side hood trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16856-A. This icon means that we're looking to buy this...

Here is our restored passenger (right hand) side hood lip moulding for any 1971 1972 1973 Mercury Cougar. We also have grade A and B used hood mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating....

Used passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches, or corrosion. Perfect for your daily driver that is in above average condition. If you send in a good core we can give you a discount on this part.Ford part # C7WY-16856-A.*NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit...

Correctly restored hood lip moulding with bright dip clear coat anodized coating. Requires that you send your core in advance.Ford part number C9GY-16856-A

Used interior quarter window moulding for the driver side (left hand) of the Mercury Cougar coupe. This trim installs vertically behind the quarter window. Unfortunately we cannot guarantee we will be able to supply the color of your choice, but we will try to accommodate.

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

This driver side moulding is correct for hardtop or coupe. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Master part number D1ZZ-6503599.*NOTE* - Excludes Mustang Fastback and Mach 1 models. ...

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang that feature two 2" gauge pods on the driver side. Sold as a pair.

1968 Mercury Cougar right side or passenger rear quarter moulding found on the GT-E models. This unique trim split the lower silver color from the body color. Arrow straight, never bumped, no damage to the raised portion, best used piece we have ever got in and the RR is the hardest of the 6 to find! We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the...

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit. Original Mercury part number is C7WY-6529034-A with a casting number of C7WB-6529034-D

Reproduction driver side (left hand) and passenger side (right hand) pair of quarter window mouldings / trim with used stainless steel mounting brackets attached. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting and or holes being drilled in them due to them coming off. We bond these to the mounting brackets in house with a liberal application of 3M Windo-Weld #08609. The factory...

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529035-A.

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529034-A.

Reproduction driver side (left hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Reproduction passenger side (right hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Core aluminum rear deck lid moulding / trim for the Mercury Cougar. Good core ready for restoration. No kinks, flattened areas of heavy pitting. Seven clips are used to install the deck lid moulding and we have new clips available here. Ford part # C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on this tricky trunk trim, check out our video below: ...

NOS aluminum deck lid moulding / trim for the Mercury Cougar. Rarely do we come across a true NOS 1967-68 aluminum deck lid moulding / trim. Starting in 1969, Ford gave you a stainless moulding as a service replacement part. Seven clips are used to install the deck lid moulding and we have new clips available here! Ford part # C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on this tricky trunk trim, check out our video below: ...

Used aluminum rear deck lid moulding / trim for the Mercury Cougar. Our used trunk lid trim is usually dull and lightly scratched as you see pictured here. Expect numerous and heavier scratches in the key hole area. We have a really hard time keeping good, straight used aluminum deck lid mouldings in stock. They are very prone to damage and many have been replaced with the 1969-70 stainless steel version which was the standard service replacement part that Ford would have sold you from 1969...

Core stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967 - 1968 Cougar is that it will not match the aluminum corner mouldings perfectly. We offer this grade of trim for those folks that are without a core for core required items. This being a core, means that it will...

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

Core driver side (left hand) lower rear window moulding / trim for the Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42405-A.

Core passenger side (right hand) lower rear window moulding / trim for your Mercury Cougar suitable for restoration or could be used on a lower quality driver. Ford part # C7WY-42404-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Used passenger side (right hand) lower rear window moulding / trim for your Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42404-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section....

Sold individually, right is the same as left. Rare find but hard to justify the price in light of the quality and price of the reproductions we offer at a fraction of the price. Notice the difference in brightness of these two NOS, fresh out of the Ford wrapper mouldings. This is actually quite common, different batches got different treatment. When you send in your trim to us to be restored it will match as it will all be done in the same "batch".

This used to be a decent off-shore quality pair of anodized aluminum mouldings. Our guess is that the tooling is starting to show wear and needs replacing as evidenced by the wrinkles in the corners. We have alerted the manufacturer but they can be slow to act. There are no returns on this blemished, less than perfect part. Ford issued a TSB (technical service bulletin) instructing the Service Departments to drill a hole through the rocker moulding into the lower fender and install a chrome...

Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...

Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...

Stainless steel throttle pedal surround trim. Self attaching to part number D1ZZ-9735-B. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. It appears that this trim may not have been used all the way through 1973. Ford probably eliminated it as a cost saving measure.

Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass, does not come with weather strip. You can use this 3M product to glue this trim to the glass. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the driver side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core driver vinyl half roof trim. Call 503-463-1130...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the passenger side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core passenger vinyl half roof trim. Call...

Rear driver side wheel lip moulding. Fits any 1971-73 Mercury Cougar.Replaces Ford part number D1WY-6529165-A.

NOS passenger side front wheel lip moulding. Rare find, better snatch it up while you can!

Front passenger side wheel lip moulding for any 1971-73 Mercury Cougar.Replaces Ford part number D1WY-16038-A.

Driver side upper windshield mouldinig. Suitable for restoration or could fit right in on or your lower quality daily driver. Ford part number C5ZZ-6503145-B.

NOS upper moulding at the top of the windshield on the left hand side. Ford part number C5ZZ-6503145-B

Driver side vertical windshield moulding. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part number C5ZZ-6503137-B.

Restored exterior driver side (left hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

Restored exterior passenger side (right hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

Core lower windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503148-B.

Core passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503144-B.

Core passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503136-B.

NOS passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503136-B.