All Products

Used wiper transmissions that will connect to the wiper motor and the output shafts. This is commonly replaced when swapping your cowl panel, steel dash panel, and/or firewall. If you want to keep your car original, go with these good used arms, or you can find the reproductions here.

Nice reproduction of the D0OZ-17C583-A windshield wiper stop as found on any 1971-73 Mercury Cougar, 1971-73 Ford Mustang, 1970-71 Ford Torino, or 1970-71 Mercury Cyclone. Zinc plated and rubber dipped like OEM Ford.Replaces Ford part number D0OZ-17C583-A.

Used and reusable backup lamp socket and wiring assembly for the reproduction reverse light chrome housings or to replace a damaged lead in your original 1969-70 Mercury Cougar reverse light. This light socket assembly uses the 1156 bulb. NOTE: These sockets are crimped from the factory and are difficult to remove. When re-installing, there won't be much "meat" left to flare out inside the bezel and you may run into issues with getting a good ground. 

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. Fits 1971 Mercury Cougar and Ford Mustang with 351C engines. About 24 inches in total length. Black wire with yellow hash marks. Ford Part #: D1ZB-19A885-B.

Reproduction Dash to Engine Gauge Feed with push-on Post Oil Sender for the 1967 and 1968 Mercury Cougar with the 289 or 302. Red / Green stripe wire = Coil White / Red stripe wire  = Temp Red / White stripe wire = Oil lamp * Note - Verify your oil pressure switch has the connector to accept the push on boot plug. Replaces Ford Part #: C6DZ-14289-BCheck out the video below on our new gauge tester: ...

Reproduction Dash to Engine Gauge Feed with Tach and Slide-on clip Oil Sender for the 1967 and 1968 Mercury Cougar with the 289 or 302. * Note - Check the style of oil pressure connector on your engine. Replaces Ford Part #: C7DZ-14289-BCheck out the video below on our new gauge tester: ...

Reproduction Dash to Gauge Feed Harness for the 1970 Mercury Cougar and Ford Mustang with either the 351C-2V or 351C-4V, Cleveland engine only. Replaces Ford Part #: D0ZZ-14289-ACheck out the video below on our new gauge tester: ...

This is the engine gauge loom that runs from the coil, temp. sender and oil sender to the pigtail on the firewall. Designed for the 1971 Mercury Cougar and Ford Mustang. Will fit the 1972 Cougar and Mustang, but technically those cars had a bundled harness that included A/C, and possibly carburetor solenoid wiring. To be clear, this harness is only as shown, basic ignition and gauge feed. Replaces Ford Part # : D1OZ-14289-CCheck out the video below on our new gauge tester: ...

Reproduction dash to engine gauge feed harness for the Mercury Cougar equipped with the 351 Windsor. All black boot plugs, this is the style used on cars with air conditioning. Fits 1969-70 Mercury Cougar with 351W engines and 1969-70 Ford Mustang with 302 or 351W engines. Check out the video below on our new gauge tester: ...

Reproduction dash to engine gauge feed harness for the Mercury Cougar equipped with the 351 Windsor. All black and yellow boot plugs, this is the style used on cars without air conditioning. Fits 1969-70 Mercury Cougar with 351W engines and 1969-70 Ford Mustang with 302 or 351W engines. Check out the video below on our new gauge tester: ...

Master clip kit which includes following fasteners:Door courtesy and speaker Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorn feedPassenger side apron below relayRadio cable to dashSide marker and headlightsTurn signal lights on hood scoopUnder dashVarious location zip tiesKeep in mind that there are many other fasteners on 1969 Cougars / Mustangs that are not in this kit. ...

Master clip kit which include the following fasteners:Door courtesy and speakerEngine feedFirewallFront crossmemberHorn feedParking light leadsPassenger side cowl brace and alternatorPassenger side shock towerRadio cable to dashSide marker lampsTaillight wiring to taillight body studsTurn signal lights on hood scoopUnder dashKeep in mind that not all fasteners found on 1970 Cougars / Mustangs are found in this kit. ...

Master clip kit which includes the following fasters:Back up light to firewallDoor speakersEngine ffeedRadio cable to dashSide marker and headlightsTaillight wiring and groundUnder dashVarious location zip tiesKeep in mind that not all fasteners found on 1971-73 Cougars / Mustangs are in this kit.

Anti rattle spring for the 1967 Cougar and Mustang clutch release lever spring. Ford part number C6AZ-7562-A.

This extension connects from the instrument cluster wiring harness to the voltage regulator. We've found these on many 68 Cougars, but not all seem to have them.

Used wire extension for the tilt / tilt away steering column found in the Mercury Cougar or ford Mustang. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts needed. To offset the cost of your rebuild, you can send us additional parts or parts columns and we will give...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.Replaces Ford Part #: C9ZB-19A885-B.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end. Replaces Ford Part #: C9ZB-19A885-B.

Used wiring harness for the 1971 Cougar right hand (passenger side) C pillar lamp. Good for both Standard and XR7 models

Used wire harness with diffusers for the instrument cluster lighting (dash lights) on the Standard or XR7 71 - 73 Mercury Cougar.  NOTE* When using LED ground sensitive bulbs, you must reverse the black and blue w/red stripe wires. Ford part number D1WB-10B898-AA

Used lead wire harness that runs from the white plug at the cowl to the throttle positioning sensor on the 71 - 73 Cougar or Mustang.Harness is red with yellow hash marks.

Wire harness extension that runs from the under dash harness to the A/C fan control switch on any 69 - 70 Cougar Standard or XR7, or the 69 - 70 Mustang.Ford part number C9ZA-19945-B

Complete 25 piece clip kit for the 1967 Cougar or Mustang. Keep in mind that this is produced as a Mustang clip kit, and although most clips are the same between Mustang and Cougar...not all clips apply to Cougar applications.   

Complete 25 piece clip kit for the 1969 Cougar or Mustang. Keep in mind that this is produced as a Mustang clip kit, and although most clips are the same between Mustang and Cougar...not all clips apply to Cougar applications.   

Reproduction Wire Loom Mounting Kit for the 1968 Mercury Cougar / Ford Mustang

Small retaining ring that secures the engine gauge feed wiring harness to the driver side valve cover. Two were used per engine. We found this part in the 1971-72 Mustang Electrical Assembly Manual. To be used with original wiring harnesses, the reproduction engine gauge feed harness does not have the clips to attach to this retainer.Ford part number D2AB-14A163-MA.

This Screw fastens the plastic guide for turn signal wires next to column under the cone by steering wheel.

Reprints of the original Ford manuals. Even if you do not service your own car this may save you some money if you hand it to your mechanic next time he does electrical work on your car...

Wiring harness segment from firewall to the convertible power top switch on any 1971-73 Mercury Cougar or Ford Mustang.  Part number D1WB-15A690-AA.

This black wire attaches to the fusible link coming off the starter solenoid on one end then passes through the firewall to mate with the top switch wiring at the other end. Correct for both XR7, Standard convertibles and power sunroof equipped Cougars.

Preproduction wiring harness, connects the convertible top switch to the pump on both the xr7 and standard model Cougars and Mustang 1969 - 1973 convertibles.

This harness connects the convertible top motor to the under dash convertible top harness under the dash. Fits 1969-70 Mercury Cougar and 1969-70 Ford Mustang. This wire rests in the trough under the passenger side sill plate and goes behind the back seat where the convertible top pump is located.Ford part number C9ZB-15A668-B.

This harness connects the convertible top switch to the pump on both the xr7 and standard 1969 - 1973 convertibles.

Wiring harness segment to the convertible power top pump on any 1971-73 Mercury Cougar or Ford Mustang. Part number D1ZB-15A668-AB.

Used wiring harness that connects 3 different wiring harnesses on any 1970 Mercury XR7 convertible. Connects the power lead from the circuit breaker under the hood, the dash switch harness, and the lead going to the convertible top pump. Ford part number D0WB-15A690-A. * Note - 1970 XR7 only, body code 76B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for...

Same harness works for driver or passenger side, sold individually.

This black wire attaches to the fusible link. The Fusible link connects to the starter solenoid with an eyelet connector, then connects to this wire with a billet connector. This wire then passes through the firewall to mate with the power top switch wiring under the dash. Correct for both XR7, Standard convertibles and power sunroof equipped Cougars in 1969, and Standard Cougar Convertibles in 1970.Casting Number: C9ZB-15A669-BFord Part Number: C9ZZ-15A669-BFits: 1969 Mercury Cougar Standard...

Used jumper wire used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used black plastic clip for holding the turn signal wiring harness to the column tube, next to the vacuum actuator. Fits any 1967 Mercury Cougar or Ford Mustang with tilt swing away steering columns.

Master clip kit which includes the following fasteners:Engine bayEngine feedFirewallFront crossmemberParking lightsPassenger side apron below relayRadio cable to dashKeep in mind that not all fasteners found on 1967 Courgars / Mustangs are in this kit.

Master clip kit which includes following fasteners: Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorns and regulatorPassenger side apron below relayRadio cable to dashKeep in mind that there are many other fasteners on 1968 Cougars / Mustangs that are not in this kit.

Reprints of the original Ford manuals. Even if you do not service your own car this may save you some money if you hand it to your mechanic next time he does electrical work on your car...

Reprints of the original Ford manuals. Even if you do not service your own car this may save you some money if you hand it to your mechanic next time he does electrical work on your car...

Used under dash to under hood connector for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.*NOTE*  This connector comes with the bolt and spring.

Used under dash wiring harness fuse block / box (with a chip or two) with wire leads for the Mercury Cougar STANDARD. This is part of the 14401 main under dash wiring harness. The difference between Standard and XR7 is that the Standard block has the pink resistance wire. *Note - The fuse blocks will have a small amount of damage or chips on it, in spite of what is shown in the picture.

Used fuse block / box and pigtail for the under dash harness on the Mercury Cougar. This is part of the 14401 main under dash wiring harness.Ford part # C6OZ-14A068-A.*NOTE* This unit has the same wire color and configuration as the 1967 version. The only difference is the wire retaining clip.