All Products

Reproduction transmission cooling lines made of Stainless Steel for the Mercury Cougar equipped with the C-6 automatic transmission and 351 engine. These lines are sold in pairs.

Reproduction transmission cooling lines made of Stainless Steel for the Mercury Cougar equipped with the C-6 automatic transmission and 351 engine. These lines are sold in pairs.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

An exact copy with a beautiful chrome mirror finish.

An exact copy with a beautiful chrome mirror finish. 1 inch deeper than stock.

An Exact copy. Natural gray paint for correct look and rust prevention. 1 inch deeper than stock.

Flawless chrome plating, available in stock depth only. Includes drain plug.

An Exact copy. Natural gray paint for correct look and rust prevention.

Flawless chrome plating, available in stock depth only. Includes drain plug.

Reproduction transmission selector tube seal for the 69 - 70 Cougar or Mustang steering columns.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

New manufactured transmission yoke for a T-5 5 speed transmission.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX  cars.  *Excludes 351C-4v and 351CJ engines.

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Used transmission tunnel specialty cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the area you're working on and send us a few digital pictures so we can cut to your needs. Pricing may not change, because we're...

Used transmission tunnel specialty cut. From a 1969 Mercury Cougar, slightly different than the 1970 tunnel.File picture of 1967 tunnel, you get a 1969 tunnel cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the...

Used transmission tunnel specialty cut. From a 1970 Mercury Cougar, slightly different than the 1969 tunnel. The 1970 tunnel has a bump out on the driver side for the manual transmission Hurst shifter clearance. File picture of 1967 tunnel, you get a 1970 tunnel cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up...

Used transmission tunnel specialty cut. From a 1971-73 Mercury Cougar.File picture of 1967 tunnel, you get a 1971-73 tunnel cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the area you're working on and send us a...

Used C-4 vibration damper for 1968 Mercury Cougars built after 1-2-1968. Transmission tail shaft must have the provision for this bracket. C4 transmissions with either 289 or 302 engines. Shown in the 1968 Chassis Assembly Manual on page 55, aka 4980 assembly. Two different styles of these are found on Cougar c4 transmissions. Most have been discarded or damaged, limited supply on hand.Replaces Ford part number C8WY-4A263-B.

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact.

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact. NOTE - When sending in your core, light pitting on the upper edge is acceptable. Heavily pitted trim will not be accepted.

Reproduction emergency / parking brake pedal pad trim piece for the Mercury Cougar or Ford Mustang. This great little reproduction looks good and is one of the little detail pieces that can separate a nice car from a mint car.Replaces Ford part # C9ZZ-2A487-C.

Used emergency / parking brake pedal pad that features all stainless steel construction. This unit cleans up very well with fine steel wool, has reusable folding tabs, and is easy to install. A great piece to finish off your interior!Replaces Ford part # C9ZZ-2A487-C.

This two piece painted trim / moulding set helps to secure the package tray in place at the bottom of the rear window. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Replaces Ford part #: C7ZZ-3656-A, concours correct for all 1967 Mustang's and Cougar's. This beveled ornamental plastic ring is for your 1967 steering wheel hub. The inner diameter is 3 3/4" and the outer diameter is 4 3/8" and it stands 5/16" tall. This ring fits many FoMoCo products but keep in mind there is another version that is completely flat like a washer. We suggest you use soapy water and heat your hub before trying to slip this on. It also helps if you go around the perimeter and...

Reproduction driver side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Driver side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1967-68 Mercury Cougar. These special cuts are removed from rust free examples from a used Cougar. Ford part number C7WY-6545119-A.

Driver side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1969-70 Mercury Cougar coupe or convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number C9WY-6545119-A.

Driver side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1971-73 Mercury Cougar coupe or convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number D1WY-6545119-A.

Reproduction passenger side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Passenger side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1967-68 Mercury Cougar. These special cuts are removed from rust free examples from a used Cougar. Ford part number C7WY-6545118-A.

Passenger side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1969-70 Mercury Cougar coupe and convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number C9WY-6545118-A.

Passenger side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1971-73 Mercury Cougar coupe and convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number D1WY-6545118-A.

Reproduction driver (left hand) side trunk floor panel with trunk drop off. This is a complete replacement for the factory spot-welded-in panel, not a partial cut.For more info on this new trunk panel, check out this video below:

Reproduction passenger (right hand) side trunk floor panel with trunk drop off. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

Comes with trunk drop offs and complete tail panel. We would be happy to modify the way in which we remove this part to best fit your needs. Figure about $250 for shipping and crating via www.forwardair.com. Please call to order this one.

Comes with trunk drop offs and complete tail panel. We would be happy to modify the way in which we remove this part to best fit your needs. Figure about $250 for shipping and crating via www.forwardair.com. Please call to order this one.

Used cover with dull chrome. This used to be a very sought after and expensive part due to how difficult they were to find. Now that our show quality reproductions are here they have little value... Great for someone that just wants their driver to look complete. Fits all 1967-68 Mercury Cougars, Standard and XR7 models. Decal inserts available separately. ...

For 1967 both the XR7 and Standard model used the decal shown on this reproduction trunk lock cover. For 1968 only the Standard model used this decal as the XR7 and XR7G had their own unique center badging. *NOTE* You will have to apply the licensed by Ford decal to the deck lock cover. Click on images to enlarge. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This is for the person who already has a decal or XR7G emblem to place in the center section. Maybe you have a custom idea? Same great quality and flawless fit as our other deck lock covers.*NOTE* After a long hiatus these are finally back in stock! They were worth the wait, the quality is really good on this new reproduction.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Beautiful reproduction truck lock cover with new XR-7 decal. Very true to original, the only noticeable difference being that the corners of the decal are slightly more trimmed than the originals. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Save your hard earned money when you buy our reproduction deck lock cover with the new XR7-G emblem already installed! Click on images to enlarge. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

*NOTE* 1969 - 1970 Convertible mats do not have any covering to the right of the gas tank. This is in fact how the originals were made. Many Convertible owners prefer to have a full cover mat. If that is you we suggest you purchase the coupe mat for your convertible.This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern. Do NOT confuse this with the light duty mat you will see...