All Products

Used Distributor / 351C-2V for the 1971 Mercury Cougar / 1971 Ford Mustang Ford part number D0OF-12127-U  

Used core distributor for 1973 Mercury Cougar and Ford Mustang with H code 351C-2V and automatic transmission. Core distributors will have correct stamping of D3ZF-CA. Original Ford part number D3ZF-12127-CA. 351 Windsor engines use a smaller distributor gear (about 1-1/4"), Cleveland.distributor gear is about 1-7/16" in diameter.

Good used original distributor for the 351 Cobra Jet.Ford Part # D2WF-12127-AA.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-GC.

Used Distributor / 351CJ for the 1973 Mercury Cougar / 1973 Ford MustangFord part number D3OF-12127-FA  

Used 1973 Mercury Cougar and Ford Mustang Q code 351 Cobra Jet distributor. Stamped D3ZF-12127-GA

Used core distributor for 1969 Mercury Cougar and Ford Mustang with H code 351W-2V and automatic transmission. Core distributors will have correct stamping of D0AF-AC. Original Ford part number D0AF-12127-AC. 351 Windsor engines use a smaller distributor gear (about 1-1/4"), Cleveland.distributor gear is about 1-7/16" in diameter.

C8WF-12127-B distributor for use on 1968 Mercury Cougar and Ford Mustang with X code 390-2V engines and automatic transmissions. May or may not have a correct or working vacuum advance attached. Two remaining in stock, dates are: 8D1, 7M27.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with S code 390-4V and automatic transmission. Core distributors will have correct stamping of C7AF-AC. Original Ford part number C7AF-12127-AC. Current unit has a date of 9B10, or February 10, 1969. Stamped C7AF-12127-AC.

Used Autolite Distributor for 1968 390-4V and 1968-69 428CJ for the Mercury Cougar, Cyclone or Ford Mustang, Torino.  Ford part number  C8OF-12127-D.  

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has two pressed in brass fittings for vacuum hoses. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1970 vacuum advance, the earlier vacuum advances had one of the vacuum fittings that screwed...

Ignitor 1 by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. There is also an upgraded Ignitor II available. -50F To 300F Working Temperature Range, 0-15,000 Rpm Range, This Easy To Install And Maintenance Free Electronic Ignition System Features Solid-State Electronics And Rotating Cobalt...

Ignitor II by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. Adaptive Dwell Control -  Dwell increases with RPM to provide an average of 4 times the available energy between 3000 and 5000 RPM and twice the available voltage at the plug. -50F To 300F Working Temperature Range,...

New Old Stock vacuum advance. This style used 1972 on Motorcraft 351-4V V-8 distributors. DD-339 and code 348 numbers associated with this unit. This is an MOTORCRAFT marked vacuum advance. Brass nipple not included, but is needed. Instructions for installation with this one too. Application is for Q code 351CJ distributors marked D2ZF-12127-GA, D2ZF-12127-GB, D2ZF-12127-GC, D2ZF-12127-HA, and D2ZF-12127-HB. Ford Part Number D2ZZ-12370-A ...

New Old Stock vacuum advance. This style used 1968-69 on Autolite V-8 distributors. A12 and DD-236 numbers associated with this unit. This is an Autolite marked vacuum advance Threaded cap and spring not included Ford Part Number C8AZ-12370-A

New Old Stock vacuum advance. This style used 1965-67 on Autolite V-8 distributors. Designed for use with a threaded nipple. DD-190 and code 303 numbers associated with this unit. This is an Autolite marked vacuum advance, there are other service replacement units marked MOTORCRAFT. Threaded nipple available separately. Ford Part Number C5AZ-12370-A

New Old Stock vacuum advance. This style used 1965-67 on Autolite V-8 distributors. Designed for use with a threaded nipple. DD-190 and code 303 numbers associated with this unit. This is an MOTORCRAFT marked vacuum advance, there are other service replacement units marked Autolite. Threaded nipple available separately. Ford Part Number C5AZ-12370-A

Reproduction single port vacuum advance for most all 1967-71 Ford V-8 engines. Fits Ford's brand of Autolite and Motorcraft distributors found on all 1967-71 Mercury Cougar and V-8 Ford Mustangs.

New Old Stock upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428.  * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...

Reproduction upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428.  * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Replaces Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...

Reproduction upper distributor bushing for 1969-73 351W, 351C, 429, and 460 Ford V-8 engines. * Note - 260/ 289 / 302 / 352 / 390 / 410 / 427 / 428 engines, all used a different upper bushing. See related items for that listing. Replaces Ford part number  C5AZ-12120-A. We measure 0. O.D., 0." I.D., and 1.750 long.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #107 or DF-342, single points cam with weights marked 13L and 18L from the top. Factory used on small block and FE distributors.  Ford part number C5AZ-12210-A.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #108 or DF-343, single points cam with weights marked 10L and 15L from the top. Factory used on small block and FE distributors.   Ford part number C5AZ-12210-B.

New Old Stock Autolite distributor cap for the 1964, 1965 1966 Ford and Mustang. Technically a service replacement cap, this cap has aluminum contacts, not brass. Fits all Ford V8 engines 1957-73. Before and beyond. Does not have "AUTOLITE" on the cap, just a "1", typical cap used 1957-1966 of Ford V-8's. Ford part number B7A-12106-A. 

Exact copy reproduction concourse correct distributor cap with raised Autolite logo. Good for all 67 - 73 Cougars and Mustangs. A must have for anyone building a show car.

New Old Stock MOTORCRAFT distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang. Technically a service replacement cap, this cap has an embossed "MOTORCRAFT" on top. Fits all Ford V8 engines 1967-73. Before and beyond.Ford part number B7A-12106-A. 

Reproduction distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang 

Reproduction Distributor Condensor for the 1967 - 1973 Mercury Cougar and Ford Mustang

NOS distributor ground wire. Direct replacement for 1967-73 Ford distributors. New old stock cable for inside the distributor, non ferrous metal, brass? Ford part number D2AZ-12264-A.

NOS distributor lead wire without the boot for the coil. There were at least two different lengths of wire leads found on 1967 Mercury Cougar and most all other Ford and Mercury distributors. This is the longer wiring harness, about 20 inches outside of the distributor. Direct replacement for 1961-67 Ford distributors.Ford part number C1VF-12216-A.

NOS distributor lead wire with green boot for the coil. Direct replacement for 1968-73 Ford distributors. There were several colors of boots that go to the coil, this is a green one as shown. Ford part number C7VY-12216-A.

Reproduction distributor lead wire without the boot for the coil. There were at least two different lengths of wire leads found on 1967 Mercury Cougar and most all other Ford and Mercury distributors. This is the longer wiring harness, about 20 inches outside of the distributor. Direct replacement for 1961-67 Ford distributors.

C8AF-12A022-A For all 1967 - 71 V-8 distributors. Concours correct head stamping. Brass plug for the stock Autolite distributors. Installs as shown.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with dual nipple connections. 

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with single nipple connections. 

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1971 Mercury Cougar or Ford Mustang with 429CJ engines. Distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1971 Mercury Cougar or Ford Mustang with 429CJ engines. Distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. 1969-70 Mercury Cougar Eliminator with Boss 302 and 1969-70 Ford Mustang with Boss 302 engines.

Sold individually Zinc (dark silver)

New rear seat to trunk steel divider for your Mercury Cougar. We had this one made specifically for the Mercury Cougar and it is designed to replace the flimsy tar based cardboard factory divider.We have noticed that after 40 plus years of chassis flex, the welds on the cross braces behind the rear seat tend to be broken. When installed properly behind the rear seat, this 18 gauge steel divider will provide stiffness to the chassis. This divider can be bonded, screwed or welded into your car...

New rear seat to trunk steel divider for your Mercury Cougar. We had this one made specifically for the Mercury Cougar and it is designed to replace the flimsy tar based cardboard factory divider.We have noticed that after 40 plus years of chassis flex, the welds on the cross braces behind the rear seat tend to be broken at the top or bottom. When installed properly behind the rear seat, this 18 gauge steel divider will provide stiffness to the chassis. This divider can be bonded, screwed or...

This restored trim piece mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Driver side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21547-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

This restored trim piece mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Passenger side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21546-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Made from clear acrylic plastic with prisms added to increase the bulb brightness.Ford originally used white nylon with no prisms, which makes the light very dull. Replaces Ford Part # D1AZ-13783-B.

Great fit. There were two different mounting tab styles used in the 1970's, this one is 100% correct for the 1971 Standard Hardtop Cougar manufactured before 6/71 and fits the early 1971 housing we sell. Ford Part # C6OZ-13783