All Products

Nice used California emissions air cleaner assembly, includes base with elbow, snorkel, heat riser and air cleaner lid. Application is any 1967 Mercury Cougar or Ford Mustang with C code 289-2V or A code 289-4V engines with closed emissions as sold in California. Elbow on air cleaner connects to the oil fill cap with a rubber hose. All good parts as shown, thermal switch in air cleaner snorkel may not work, and no we cannot test them.Even if you are not currently running all original parts...

Fits all V8s with oval air cleaner.

NOS new old stock vacuum motor, for early 1968 air cleaner snorkels. Up until about April 1968, the air cleaner snorkels were vacuum operated for the trap door going to the exhaust heat riser. Tested as working. Fits a wide variety of Ford cars in 1968. Don't forget to save the heavy washer that goes over the shaft from your old assembly. Ford part number C8AZ-9D612-A.

A Complete A/C and heater control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Check back often, this type and grade of part is seldom in stock very long.Ford part # C7WA-19980-A.

A Complete A/C heater control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Check back often, this type and grade of part is seldom in stock very long. Ford part # C8WA-19980-A.

A/C and heater control bezel or face plate. Grade A- used condition, standard pebble grain trim. Check back often, this type and grade of part is seldom in stock very long.Bezel only, no levers or switch.Ford part # C7ZA-19C705.

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Current dates: None - Specify...

1964-66 Ford and Mercury alternator bracket with air conditioning adjusting pulley. Pulley has new bearing installed. Application is 1964-66 Ford and Mercury full sized cars and Thunderbird. All with 352, 390, 410, 427, or 428 FE engines with air conditioning and without thermactor smog. Pulley has been professionally rebuilt with new bearing in house. Pulley has a few small rust pits, that can be filled and painted by the purchaser. Pulley is straight and true, pulley has Ford casting number...

Nice American made reproduction bracket. Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines, all with Thermactor smog pumps. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.

Reproduction gold dichromate 10 blade alternator fan. Used on Mercury Cougars and Ford Mustangs manufactured after 11/17/1969. Actually this is a Ford part found on most all Ford automobiles from 1970-73. 10 blade alternator cooling fan. Replaces Ford Part #: DOAZ-10A310-B

[No Description Provided]

Replaces Ford Part # D0WY-14305-C & D0WY-14305-A

Older used aluminum intake manifold. Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

7TPF Factory AM radio for any 1967 Galaxie or LTD models. Unknown working condition.

Used radio from a 1974 Mercury Comet or Ford Maverick. Should fit other years too. This is a mono radio, meaning that it is a single channel radio without stereo. That is the way they were built for the Maverick and Comet cars all the way back to 1970. Both the AM and FM radio bands function properly, selector buttons all work properly, comes with used knobs as shown. The only two defects on this radio are the small crack in the lens (shown in photo), and the cut electrical plug. We have...

New old stock amp gauge for the 1969 Mercury CougarFord part number C8WY-10850 Check out the video below on our new gauge tester: ...

Correct three part, telescoping, round base antenna. Comes with round ridged base gasket.*Customer Feedback* "Aloha Don, The antenna showed up with the rest of the USPS sent items. Got in here in three days. Point of installation of antenna. Tie a string to the plug side of the antenna assembly when pulling out from fender so that you can use the string to pull the new antenna plug back through the fender and into the car. Thought of that after pulling antenna out. I was able to use a flexible...

Used anti rattle pad for the stone guard on the Mercury Cougar. This unit is for the 1970 Mercury Cougar specifically and will not fit any other year. These pads must be used with the 1970 Cougar front bumper mounting brackets and the brackets can identified with the square cut window for mounting this pad. Our pad is sold individually and two are required per car.

Reproduction pair of anti rattle pad for the stone guard used on the Mercury Cougar. This unit is for the 1970 specifically and will not fit any other year. These pads must be used with the 1970 front bumper mounting brackets and the brackets can identified by the square cut window for mounting this pad. Sold in pairs and two are required per car.

Reproduction of the protector felt pad between the spare tire and jack handle for the 68 through 70 Mercury Cougar with styled steel wheels. Used only in conjunction with applications that store the jack components on top of the wheel.

Replaces Ford Part # C8AZ-2B164-A Sold individually

WCCC developed walnut straight grain kit for rimblow horn pad restorations. Fits all Standard / Decor (non-XR-7) 1969 Cougar hardtop and convertibles. All three pieces were carefully plotted on a computer program to account for their unique contoured shape for each individual insert. Detailed instructions included for preparation and installation. We suggest detailing your horn pad plastic insert, prior to applying this wood grain kit for best results. *NOTE* Fits 1969 rimblow horn pad plastic...

Pressure die cast, with quality chrome sun visor center bracket and rear view mirror mount. Replaces one of the most visible interior parts on a 1967 Mustang or Cougar. Break away style, two piece construction. Beware of cheap single piece imitations that are available as they are unsafe. Keep in mind you will have to give your screw driver some good pressure when installing to make the mirror fit tight. Replaces Ford part # C7ZZ-17690-A.These are manufactured in the USA. ...

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Reproduction front armrest in saddle for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard...

Good used arm rest with no cracks, burns or heavy discoloration. No reproductions to this date have been able to correctly match the original in look or feel.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # C8ZZ-6524100-BK.

Although many would disagree, these are in my opinion average quality. "BUT" they are currently the best available reproduction. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue, Parchment, Ivy Gold, Aqua , Saddle, or Nugget Gold. Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests are not correctly colored for the...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

Used driver side (left hand) rear armrest for the Mercury Cougar that is in grade A condition. Grade "A" armrests are not pulling away from their backing and have no splits, cigarette burns or other obvious defects. They may need to be painted with vinyl paint, especially since we can almost guarantee we will not have both sides in your color in stock. Please indicate in the notes which color you would prefer, we will do our best to accommodate you. *NOTE* If you have a standard or decor 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

This is a very rare find. "Grade A" 1969 XR7 / Shelby only, crack free original lid. Grade A will exhibit minimal loss of texture and will still be pliable. Notice how the three humps stand taller and rounder than the reproduction. Limited colors on hand, please let us know which color you desire and we will try to accommodate. Pictured pad is for reference only. The 1970 version was a soft spongy material. 

Good used solid panel with all parts removed. Panel measures 19.5" x 39". Whereas at first glance these may all look the same, the contour of the roof changes with the body style changes. Call us for price and availability on panels with varying degrees of repairable rust.

Good used solid panel with all parts removed. Panel measures 19.5" x 39". Whereas at first glance these may all look the same, the contour of the roof changes with the body style changes. Call us for price and availability on panels with varying degrees of repairable rust.

Used under dash ashtray assembly for non-console 1970 Mercury Cougar and Ford Mustang. Pebble grain finish that you paint to match your interior color. Comes as shown with light.