All Products

Set of Four Reproduction Rear Leaf Spring Center Mount Insulator Pads for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody...

These were used to mount the Fuel, Temp and Oil gauges on both Standard and XR7 models. Includes 2 mounting nuts.

C6OE-9425-A Cast iron intake manifold used on all 1967 C code 289-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C6OE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4AZ-9424-H. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

C8AE-9425-B Cast iron intake manifold used on all 1968 C code 289-2V, and F code 302-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C8AE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4AZ-9424-J. The 1966-67 289-2V intake is also a good alternate, see related items for that one.*Installation Tip - A 1 inch aluminum spacer...

C6OE-9425-B Cast iron intake manifold used on all 1967 A code 289-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C6OE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4OZ-9424-G. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

Very rare over the counter, Group II dress up accessory item for any 289 / 302 small block engine. In excellent used condition with no cracks, stripped threads or corrosion damage. The nicest you will ever find. This over the counter Intake was marketed by Shelby American in the Cougar catalog titled "How To Sharpen Your Cat's Claws". Shelby casting number S2MS-9424-A. This intake is basically the same one you so often see with COBRA lettering on it. New to our inventory as of 12-15-2017, the...

C8ZE-9425-A Cast iron intake manifold used on all 1968 J code 302-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8ZE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4OZ-9424-H. *Installation Tip - A 1 inch 4 barrel aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

D0AE-9425-M Cast iron intake manifold used on all 1970 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-M. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D1AE-9425-DA Cast iron intake manifold used on all 1971-72 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D1AE-9425-DA. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D1AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D3AE-9425-CA Cast iron intake manifold used on all 1973 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D3AE-9425-CA. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D3AZ-9424-C. *Installation Tip - A spacer plate with EGR provision is needed for proper installation. *Note - 351 Cleveland engines only. ...

D0AE-9425-E, -H, or -L Cast iron intake manifold used on all 1970-71 M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-E, -H, or -L . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-C. *Note - 351 Cleveland engines only.

Cast iron intake manifold used on all 1973 Q code 351-4V or 351CJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D3ZE-9425-AA . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D3ZZ-9424-A. *Note - 351 Cleveland engines only. *Installation Tip - A spacer plate with EGR provision is needed for proper installation. ...

C9OE-9425-A or -F Cast iron intake manifold used on all 1969-70 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C9OE-9425-A or -F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9OZ-9424-A. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

C9OE-9425-B Cast iron intake manifold used on all M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9OE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9OZ-9424-B. Casting number can also be C9OE-9425-D, or C9OE-9425-E. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air...

C6AE-9425-G Cast iron intake manifold used on very early 1967 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold, used before 1-11-1967. Take off manifold with correct casting number of C6AE-9425-G. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-N. This manifold will need to be cleaned and hot tanked prior to use. Current dates available: 6F22, 6L15. *Note -...

C7AE-9425-E Cast iron intake manifold used on 1967 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold, used before 9-11-1967. Take off manifold with correct casting number of C7AE-9425-E. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-K. This manifold will need to be cleaned and hot tanked prior to use. Current dates available: 7A31, 7C27, 7D3,  *Trivia -...

C3AE-9425-B Cast iron intake manifold used on all 1963 390-4V engines in a Mercury or Ford. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C3AE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Fits FE engines, this could have come from a Galaxie or Thunderbird or full sized Mercury. Probably also 352 engines. Current date available: 2M29. December 29, 1962. *Trivia - One of the heaviest car...

C8AE-9425-A Cast iron intake manifold used on all 1968 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8AE-9425-A.  Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C8AZ-9424-A or -B. There is also a C8AE-9425-F version that we offer on another listing.  Current dates available: 7H12, 7H17, 7L10, 7L17,...

C8AE-9425-F Cast iron intake manifold used on all 1968 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with casting number of C8AE-9425-F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C8AZ-9424-C. There are other versions of this "S" intake manifold with a suffix "A" letter.  Current dates available: 8A23. *Trivia - One of the heaviest car...

Used C8OE-9425-C Cast iron intake manifold used on all 1969 - 1970 Q and 1968 - 1970 R code 428CJ and 428SCJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8OE-9425-C . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford part number C8OZ-9424-B.  Current date code is 9C25 or March 25, 1969 and 0A19 or January 19, 1970. *Trivia - One of the heaviest...

Reproduction lightweight aluminum high performance intake manifold with the Cobra logo. This is an exact copy of the manifolds Carol Shelby offered on his Shelbys and Cobras in the late 1960's. Fits 260,289 and 302 engines.You can find the SHELBY lettered intake here. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

Reproduction lightweight aluminum high performance intake manifold with the Shelby logo. This is an exact copy of the manifolds Carol Shelby offered on his Shelbys and Cobras in the late 1960's. Fits 260,289 and 302 engines.You can find the COBRA lettered manifold here. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

Reproduction intake manifold valley pan for the Mercury Cougar or Ford Mustang equipped with the 351 Cleveland engine with the 2V (2 barrel) heads.

Ford licensed reproduction of the interior assembly manual for the 1970 Ford Mustang that shows information provided to those assembling the cars on the assembly lines.  Much of the information is also applicable to the 1970 Mercury Cougar.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.

LED dome light bulb for the standard (non-XR7) 1791, 1972, or 1973 Mercury Cougar.

Used on both the Xr7 and Decor / Deluxe interiors with moulded door panels.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Reproduction rear courtesy / opera light lenses for the Mercury Cougar. The rear courtesy / opera lights were standard equipment on all XR7 Cougars, but were a popular option many other standard and decor level interior Cougars. If your car did not originally come equipped with them, it is actually quite easy to install them, but you will need to purchase our used housing /socket assemblies. These are fantastic quality and a perfect fit. Sold as a pair only. Ford part # C6VB-13B726-A. *TRIVIA*...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Upholstery components have an ETA of 5 - 9 weeks.Reproduction Houndstooth upholstery kit in black and white for the front and rear seats of the Mercury Cougar coupe.*NOTE* This product will take 16-18 weeks for delivery.

Upholstery components have an ETA of 5 - 9 weeks.Nothing captures the feel of 1970 like the hounds-tooth pattern that once again has become fashionable... Now this ultra cool material has been correctly reproduced and we are the first to offer it in a pre-sewn ready to install kit. The houndstooth option was available on both decor and XR7 Cougars and also was available on the Eliminator in black and white only. Houndstooth cloth interior was never offered in a convertible from the factory but...

Upholstery components have an ETA of 5 - 9 weeks.Nothing captures the feel of 1970 like the hounds-tooth pattern that once again has become fashionable... Now this ultra cool material has been correctly reproduced and we are the first to offer it in a pre-sewn ready to install kit. The houndstooth option was available on both decor and XR7 Cougars and also was available on the Eliminator in black and white only. Houndstooth cloth interior was never offered in a convertible from the factory,...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag trim Code: 2K.    This is a full interior seat cover set for both bucket seats and the rear seat or you can select fronts only. Choosing who to buy your interior kit from is confusing to say the least as no company will boast "Ill Fit & Poor Materials!". In fact there are many companies selling less than quality products and prices for poor quality can run the gamut from $225-$500 per kit! Here are a few points I...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2K.    Decor upholstery kit to cover both bucket seats. Choosing who to buy your interior kit from is confusing to say the least as no company will boast "Ill Fit & Poor Materials!". In fact there are many companies selling less than quality products and prices for poor quality can run the gamut from $225-$500 per kit! Here are a few points I would like to point out on our 1968 Mercury Cougar Decor Interior...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2K.     Decor upholstery kit to cover the rear seat. Choosing who to buy your interior kit from is confusing to say the least as no company will boast "Ill Fit & Poor Materials!". In fact there are many companies selling less than quality products and prices for poor quality can run the gamut from $225-$500 per kit! Here are a few points I would like to point out on our 1968 Mercury Cougar Decor...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2A.    This is a full interior seat cover set for both bucket seats and the rear seat or you can select fronts only. Choosing who to buy your interior kit from is confusing to say the least as no company will boast "Ill Fit & Poor Materials!". In fact there are many companies selling less than quality products and prices for poor quality can run the gamut from $225-$500 per kit! Here are a few points I would...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2A.    Decor upholstery kit to cover both bucket seats. Choosing who to buy your interior kit from is confusing to say the least as no company will boast "Ill Fit & Poor Materials!". In fact there are many companies selling less than quality products and prices for poor quality can run the gamut from $225-$500 per kit! Here are a few points I would like to point out on our 1968 Mercury Cougar Decor Interior...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2A.      Decor upholstery kit to cover the rear seat. Choosing who to buy your interior kit from is confusing to say the least as no company will boast "Ill Fit & Poor Materials!". In fact there are many companies selling less than quality products and prices for poor quality can run the gamut from $225-$500 per kit! Here are a few points I would like to point out on our 1968 Mercury Cougar Decor...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2K.    Aqua Decor Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2K.    Aqua Decor Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like aqua are not always...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2A.    Black Decor Interior Upholstery Kit to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2A.    Black Decor Interior Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like aqua are...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2D.    Dark Red Decor Upholstery to covet the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors...

Upholstery components have an ETA of 5 - 9 weeks.Door Tag Trim Code: 2D.    Dark Red Decor Upholstery to cover the rear seat for the 1969 Mercury Cougar Convertible. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the...